The Alice Pixel Detector (ALPIDE) is developed for the upgrade of the Inner Tracking System of the ALICE experiment at CERN, which will take place during second Long Shutdown in 2019-2020. ALPIDE is a Monolithic Active Pixel Sensor (MAPS), manufactured in a 180 nm CMOS Imaging Process of TowerJazz. Forecoming tracking detectors, based on this technology, will see strong advantages with the application of these sensors as they provide the highest capabilities in spatial resolution and utmost potential for being thin. In this work, the results of the ALPIDE sensor beam test, which took place at the Beam Test Facility of Laboratori Nazionali di Frascati, are presented

Fantoni, Alessandra

Gianotti, Paola

Larionov, Pavel

Matuoka, Paula F. T.

Muccifora, Valeria

Pisano, Silvia

Ronchetti, Federico

Spiriti, Eleuterio

Toppi, Marco

English

Open Access Repository

LABORATORI NAZIONALI DI FRASCATISIDS-PubblicazioniINFN-17-16/LNFMay 6, 2017BEAM TEST OF ALPIDE SENSORAlessandra Fantoni1, Paola Gianotti1, Pavel Larionov1,Paula F.T. Matuoka3, Valeria Muccifora1, Silvia Pisano1,2,Federico Ronchetti1, Eleuterio Spiriti1, Marco Toppi11)INFN, Laboratori Nazionali di Frascati, P.O. Box 13, I-00044 Frascati, Italy2) Museo Storico della Fisica e Centro Studi e Ricerche “Enrico Fermi”, I-00184 Roma, Italy3) Instituto de Fı́sica da Universidade de São Paulo, 05508-090 São Paulo, BrazilAbstractThe Alice Pixel Detector (ALPIDE) is developed for the upgrade of the Inner TrackingSystem of the ALICE experiment at CERN, which will take place during second LongShutdown in 2019-2020. ALPIDE is a Monolithic Active Pixel Sensor (MAPS), manu-factured in a 180 nm CMOS Imaging Process of TowerJazz. Forecoming tracking detec-tors, based on this technology, will see strong advantages with the application of thesesensors as they provide the highest capabilities in spatial resolution and utmost potentialfor being thin. In this work, the results of the ALPIDE sensor beam test, which took placeat the Beam Test Facility of Laboratori Nazionali di Frascati, are presented.1 IntroductionThe Inner Tracking System (ITS) of the ALICE experiment at CERN will undergo a ma-jor upgrade during the second long shutdown (LS2) in 2019-2020, intended to improvethe tracking and vertexing capabilities of the system [1]. The present ITS will be entirelyreplaced with a new system based on Monolithic Active Pixel Sensors (MAPS). The up-graded ITS will be composed of 7 cylindrical barrels located at different distances fromthe interaction point, where each barrel is build with sensor module structures known asstaves.The Alice Pixel Detecor (ALPIDE), the main component of the new ITS, is being pro-duced with a 0.18 µm CMOS technology feauturing a design optimized for the upgradedITS. The ALICE group at LNF, one of the assembly and testing sites involved in theproduction of the Outer Barrel (OB) of the system, will produce and test 27 staves eachcomprising 196 ALPIDE sensors. Each OB stave will be composed of 14 Hybrid In-tegrated Circuit (HIC), an assembly consisting of the polyimide flexible printed circuit(FPC) on which the ALPIDE chips (2×7) and some passive components are bonded [2].In this note, the results of a beam test performed in the BTF at LNF, devoted to the study ofsome basic features of the ALPIDE sensor, will be reported. For this purpose the ALPIDEsensor has been combined to a MIMOSA-28 sensor [3]. This test have to be considered asa feasibility study to work with such combined ALPIDE/MIMOSA-28 tracking system.Such a system will be helpful in order to study and test the assembled final staves.2 Setup2.1 ALPIDEALPIDE is a CMOS MAPS sensor developed by the ALICE collaboration and manufac-tured by TowerJazz on high-resistivity epitaxial silicon layer with a highly doped p-typesubstrate (Fig. 1a). The sensor features a matrix of 512 rows and 1024 columns of pix-els where a single pixel measures 27 µm × 29 µm in rφ and z planes, respectively [2].Each pixel hosts the front-end electronics, which includes an analogue section with signalamplification, shaping and discrimination as well as the digital section which includespixel storage and masking registers (Fig. 1b). The 3-bit in-pixel buffer allows to store thediscriminated hit information, which is read-out when a global strobe signal arrives bythe priority encoder circuits [4]. The front-end parameters of the chip were optimized inorder to achieve the readout capability of 100 kHz, which is beyond the expected scenarioof the luminosity increase after the LS2. In this work, the final prototype of the sensor,ALPIDE v4, was used.2(a)(b)Figure 1: (a) Schematic view of the ALPIDE pixel sctructure [2]; (b) Schematic view ofthe front-end part of the ALPIDE pixel [4].2.2 MIMOSA-28The MIMOSA-28 or Ultimate sensor was developed for the upgrade of the inner trackingsystem of the STAR experiment at RHIC [3]. It has a pixel matrix of 928 (rows) × 960(columns) with a single pixel size of 20.7 × 20.7 µm2. The sensor employes a rollingshutter readout technique with a 185.6 µs frame readout time.2.3 Beam Test FacilityThe testbeam have been performed at the Beam Test Facility of Laboratori Nazionali diFrascati. The BTF provides electron and positron beams of an energy up to 500 MeVin bunches, with a 1-50 Hz repetition rate and the maximum beam current of 500 mA(e−) and 100 mA (e+), which turns into approximately a factor of 5 difference in electronand positron bunch multiplicites [5]. In this work, both electron and positron beams of a450 MeV energy, were used at the maximum repetition rate of 50 Hz.3Figure 2: General view of the test setup assembled in the BTF hall.2.4 Setup arrangementThe setup, consisting of one ALPIDE and one M28 sensors, was mounted on a preci-sion remotely controllable table located several tens of centimeters far from the beamextraction window (Fig. 2). The sensors were mechanically assembled on custom madealuminum frames which were mounted on a rail like structure. Here, the ALPIDE sen-sor was placed inside a carrier board that provides the required power connection to thefront-end part of the chip and to its biasing structures (Fig. 3).2.5 Data acquisitionThe readout of the ALPIDE sensor was performed using an FPGA (Field ProgrammableGate Array) based MOSAIC board [6]. The M28 sensor was read-out via a system basedon a SoCKit development kit [7]. In order to synchronize both acquisition systems, theBTF bunch crossing trigger was connected to the input of the MOSAIC board and anoutput signal 1 of the MOSAIC board was used as a trigger for data acquisition of theM28 system. In this case, only the events counted by the MOSAIC board were registeredby the MIMOSA data acquisition.1VETO signal of the bunch crossing trigger and the BUSY state of the MOSAIC board.4Figure 3: Carrier board with the ALPIDE sensor mounted on the supporting aluminumframe.3 ResultsFor each sensor a raw data output file is produced containing a list of the fired (hit) pixelswith the corresponding trigger numbers. Each pixel is identified by a row and a col-umn number. An ionizing particle impinging a MAPS produces charge carriers that arecollected by one or more adjacent pixels. Such a group of pixels is called a cluster. A clus-tering algorithm based on the first neighbour search approach has been used to identifyclusters for each sensor. Two pixels are called first neighbours if they are contiguous inrow or column, i.e. if their row (column) number is the same and the difference betweentheir column (row) number is equal to one. The clustering algorithm produces, for eachtrigger number, a list of reconstructed clusters, their cluster size (the number of pixel percluster), the X and Y positions of the cluster center of gravity (CoG) in pixels unit and theRMS values of the latter.The X-Y position of the reconstructed clusters is shown in Fig. 4a for ALPIDE and inFig. 4b for M28 sensor. The difference in the number of entries in case of ALPIDEand M28 sensors depends on different setting of the thresholds of the two sensors. Thedifference in the beam profile by looking at the X-Y RMS for ALPIDE and M28 sen-sors, is compatible with the multiple scattering of 450 MeV electrons and positrons in100 µm of silicon (ALPIDE thickness). The beam spot size measured by ALPIDE isRMSx ≈ 1.4 mm and RMSy ≈ 1.5 mm, including the multiple scattering of the beam inthe air between the beryllium exit window of the beam pipe and the ALPIDE sensor.A dedicated acquisition of the noise has been performed in order to mask the noisy pixelsin both sensors. In the case of ALPIDE, three noisy pixels have been masked. After the5X [pixel]0 200 400 600 800 1000Y [pixel]02004006008001000Entries  396020Mean x   193.7Mean y     602RMS x    50.5RMS y   52.881−10110(a) ALPIDEX [pixel]0 200 400 600 800 1000Y [pixel]02004006008001000Entries  123554Mean x   451.4Mean y   571.1RMS x   74.33RMS y   78.13110210(b) M28Figure 4: Distribution of the clusters’ center of gravity in X-Y for ALPIDE (a) andM28 (b) sensorsmasking, the fake hit rate was reduced to 10−12 hits/pixel/event. The fake hit rate for M28sensor is < 5 × 10−9 hits/pixel/event: some noisy hits is still clearly visible (see Fig. 4bfor X < 200 pixels). This noise can be removed for future beam tests by masking furtherremaining noisy pixels.In Fig. 5a the number of the clusters per event versus the event number is shown for bothsensors. The number of the clusters per event depends on the bunch multiplicity. Lookingat Fig. 5a it is possible to distinguish between electrons and positrons, as the electronmultiplicity in BTF is in average about 5 times the positron one (see Sec. 2.3). No beamis present during the switch from electrons to positrons. In Fig. 5b the distribution ofthe number of clusters per event is shown in the case of the ALPIDE sensor. Here it waspossible to distinguish between positrons and electrons, selecting on the basis of the eventnumber from Fig. 5a the two different contributions. The electron and positron distribu-tions are poissonian with mean number of clusters per event 7.4 and 1.7 respectively. Foreach event all the available combinations of the clusters CoG of the M28 sensor and ofthe ALPIDE have been considered in order to select the clusters correlated to the passageof a particle through both sensors. These combinations are shown in Fig. 6 for both theX (top) and Y (bottom) positions of the cluster center of gravity. The correlated clustersare the ones lying along the line clearly visible in both the plots of Fig. 6, while all theother cluster combinations form a combinatorial background corresponding to the blobvisible in each of the two plots of Fig. 6. Such combinatorial background is due to thematching of two clusters not belonging to the same particle, considering that the averagemultiplicity is greater than one. Another contribution to such combinatorial backgroundcomes from the matching of a cluster due to an impinging particle with another one dueto noise. The latter case is mainly due to the noise from the M28 sensor, as clearly visible6Event number0 20 40 60 80 100310×Number of clusters per event0510152025MIMOSAALPIDE+e-e(a)Number of clusters per event0 5 10 15 20Entries0200040006000800010000electronspositrons(b)Figure 5: (a): Distributions of the number of clusters per event versus the event numberfor both the sensors. (b): Distribution of the number of clusters per event for ALPIDE.in the top of Fig. 6: the vertical line for X MIMOSA<50 corresponds to a noisy clusterof M28 sensor that matches with all the available clusters from ALPIDE for that event. InX_MIMOSA [pixel]0 200 400 600 800 1000X_Alpide [pixel]0100200300400500Y_MIMOSA [pixel]0 200 400 600 800 1000Y_Alpide [pixel]02004006008001000Figure 6: Combinations between all the clusters positions in x (top) and y (bottom) of thetwo sensors. The correlated clusters are the ones lying along the line.order to select only the correlated clusters, a linear fit has been done as shown in Fig. 6and the distance between all the clusters’ positions and the line has been computed, se-lecting as good events the ones within a distance of 5σ. Using only such selected events,the mean cluster size of the M28 and ALPIDE sensors was measured to be approximately72.5 and 1.8 pixels respectively.4 ConclusionsThe ALPIDE chip has been developed for the upgrade of the ITS of the ALICE exper-iment at CERN, foreseen for the LS2 of the Large Hadron Collider (2019-2020). TheALICE LNF group will participate in the assembly of the detector, taking care of the pro-duction and tests of 27 OB staves.In this work, the results of a beam test performed in the BTF at LNF with an ALPIDE anda M28 sensors, have been presented. This test has to be considered as a preliminary testexploring the possibility to work with the combined ALPIDE/M28 system, never usedtogether until now. The clusters spatial distribution was exploited to study the beam size(RMSx ≈ 1.4 mm and RMSy ≈ 1.5 mm) and the number of clusters per event was usedto monitor the beam multiplicity. The system was succesfully syncronized and it waspossible to correlate the clusters of the two sensors related to the same particle, event byevent. The cluster size was found to be approximately 1.8 for ALPIDE and 2.5 for M28sensor in pixel unit, selecting just the correlated events.No tracking algorithm has been implemented in this preliminary test with only two sen-sors, but it will be developed for future beam tests exploiting more M28 and ALPIDEsensors together to form a tracking telescope. With such apparatus it will be possible tostudy the ALPIDE efficiency detection at different back bias voltages and threshold con-ditions. It is also planned to test a HIC in laboratory and in a future beam test at the BTFfacility.Last but not least, it is worth to stress that the development of the MAPS sensors and therelated assembly technologies is not only restricted to the field of high energy physicsexperiments but also opens a range of new opportunities for applications that benefit fromhigh spatial resolution devices.5 AcknowledgementsThis work has been partly supported by the Ministero degli Affari Esteri e della Co-operazione Internazionale (MAECI) of the Italian government in the framework of theMONOPIXEL project and by the Museo storico della Fisica e Centro di studi e ricercheEnrico Fermi. Authors would like to thank Aldo Orlandi (INFN, Laboratori Nazionali diFrascati) for the construction of the mechanical support for the ALPIDE/M28 combinedsystem. We would also like to thank the BTF team for their technical support.References[1] G. Aglieri Rinella, NIM in Phys. Res. A 845 (2017) 583–587.[2] ALICE Collaboration, Journal of Physics G 41 (2014) 087002.8[3] G. Contin for the STAR collaboration, Nuclear Physics A 956 (2016) 858–861.[4] ALPIDE Operations manual, 2015.[5] G. Mazzitelli et al., NIM in Phys. Res. A 515 (2003) 524–542.[6] G. De Robertis et al., MPGD2015 conference, poster.[7] SoCKit development kit, http://www.terasic.com.tw/cgi-bin/page/archive.pl?Language=English&CategoryNo=167&No=816&PartNo=1.9

Beam test of ALPIDE Sensor

https://www.openaccessrepository.it/record/76740/files/beam-test-of-alpide-sensor_.._.._Note_INFN_INFN-17-16-LNF.pdf

Beam test of ALPIDE Sensor

Abstract

Similar works

Full text

Available Versions

Open Access Repository