A fast-timing experiment was performed at the Argonne National Laboratory in December 2015 and January 2016, measuring decay radiation of fission products from a 252Cf fission source. Details of the set-up, integration with Digital Gammasphere, and the data acquisition system are presented. The timing performance of the set-up, capable of measuring lifetimes from the nanosecond region down to tens of picoseconds, is discussed. First preliminary results from the fast-timing analysis of the fission fragment data are presented

Anderson, J.T.

Ayangeakaa, A.D.

Berry, T.

Bottoni, S.

Bruce, A.M.

Burrows, I.

Carmona Gallardo, M.

Carpenter, M.

Carroll, R.

Copp, P.

Cullen, D.

Daniel, T.

Fernandez Martinez, G.

Fraile, L.

Gamba, E.R.

Grant, A.

Greene, J.P.

Guegi, L.A.

Hartley, D.

Ilieva, R.

Ilieva, S.

Janssens, R.V.F.

Kondev, F.G.

Kröll, T.

Lalkovski, S.

Lane, G.J.

Lauritsen, T.

Lazarus, I.

Lotay, G.

Podolyak, Zs.

Pucknell, V.

Reed, M.

Regan, P.H.

Rohrer, J.

Rudigier, M.

Sethi, J.

Seweryniak, D.

Shand, C.M.

Simpson, J.

Smolen, M.

Stefanova, E.

Vedia, V.

Yordanov, O.

Zhu, S.

Carolina Digital Repository

Vol. 48 (2017) ACTA PHYSICA POLONICA B No 3FAST TIMING MEASUREMENT USING AN LaBr3(Ce)SCINTILLATOR DETECTOR ARRAY COUPLED WITHGAMMASPHERE∗M. Rudigiera,†, S. Lalkovskia, E.R. Gambab, A.M. BrucebZs. Podolyaka, P.H. Regana,c, M. Carpenterd, S. ZhudA.D. Ayangeakaad, J.T. Andersond, T. Berrya, S. BottonidI. Burrowse, R. Carrolla, P. Coppf , D. Culleng, T. DanielaL. Fraileh, M. Carmona Gallardoh, A. Grante, J.P. GreenedL.A. Guegia, D. Hartleyi, R. Ilievaa, S. Ilievaj, R.V.F. JanssensdF.G. Kondevk, T. Kröllj, G.J. Lanel, T. Lauritsend, I. LazaruseG. Lotaya, G. Fernandez Martinezj, V. Pucknelle, M. ReedlJ. Rohrerd, J. Sethid, D. Seweryniakd, C.M. Shanda, J. SimpsoneM. Smolenm, E. Stefanovan, V. Vediah, O. YordanovnaUniversity of Surrey, Guildford, UKbUniversity of Brighton, Brighton, UKcAIR Division, National Physical Laboratory, Teddington, TW11 0LW, UKdPhysics Division, Argonne National Laboratory, Lemont, IL, USAeSTFC Daresbury Laboratory, Daresbury, UKfDept. of Physics and Applied Physics, University of Massachusetts Lowell, Lowell, IL, USAgUniversity of Manchester, Manchester, UKhUniversidad Complutense, Madrid, SpainiU.S. Naval Academy, Annapolis, Maryland, USAjTechnische Universität Darmstadt, Darmstadt, GermanykNuclear Engineering Division, Argonne National Laboratory, Lemont, IL, USAlAustralian National University, Canberra, AustraliamUniversity of the West of Scotland, Paisley, UKnInstitute for Nuclear Research and Nuclear Energy, Sofia, Bulgaria(Received December 14, 2016)A fast-timing experiment was performed at the Argonne National Lab-oratory in December 2015 and January 2016, measuring decay radiationof fission products from a 252Cf fission source. Details of the set-up, in-tegration with Digital Gammasphere, and the data acquisition system arepresented. The timing performance of the set-up, capable of measuringlifetimes from the nanosecond region down to tens of picoseconds, is dis-cussed. First preliminary results from the fast-timing analysis of the fissionfragment data are presented.DOI:10.5506/APhysPolB.48.351∗ Presented at the Zakopane Conference on Nuclear Physics “Extremes of the NuclearLandscape”, Zakopane, Poland, August 28–September 4, 2016.† Corresponding author: m.rudigier@surrey.ac.uk(351)352 M. Rudigier et al.1. IntroductionThe fast timing method is a well-established tool for measuring lifetimesof excited nuclear states [1, 2]. Especially since γ–γ fast timing in thesub-nanosecond region has become feasible using LaBr3(Ce) scintillators,many studies in different mass regions have employed this method, moreand more also in studies of very exotic nuclei using radioactive beams (e.g.β–γ timing at RIKEN [3]) or neutron induced fission sources (e.g. FATIMAat EXILL [4]).When employing methods like nuclear fission, which create an abundanceof different isotopes, care has to be taken to select a particular isotope ofinterest. Especially in fast timing measurements using LaBr3(Ce) detectors(LaBr) it is very important to have good isotope selection, in order to setclean energy gates. One way to achieve this is by coupling the fast timingdetectors with a High-Purity Germanium (HPGe) detector array. The su-perior energy resolution of the HPGe detectors allows resolution of singletransitions in a nucleus of interest. Coincident γ–γ events detected with theLaBr array can then be used to apply the fast timing technique. With itshigh efficiency, Gammasphere is ideal for this kind of task.25 FATIMA detectors of the UK NuSTAR Collaboration [5, 6] composedthe fast timing array in this experiment. The fast timing data acquisitionsystem (DAQ) used is a compact and flexible system with sub-nanosecondtiming based on semi-digital VME electronics. This experiment was also afirst field test for this new DAQ system. There has been one experimentbefore, which used two LaBr detectors with Gammasphere [7]. However,this is the first measurement with a large fast timing array coupled withDigital Gammasphere. The focus of this article lies on the fast timing partof the set-up. For a detailed description of Gammasphere and the DigitalGammasphere (DGS) acquisition system, see [8, 9].2. Fast timing array coupled with GammasphereThe detector arrays were arranged in two hemispheres, see Fig. 1 (a).The 252Cf fission source was placed at the focus of one hemisphere of theGammasphere array (50 High-Purity Germanium (HPGe) detectors) whichwas coupled with a fast timing array, comprising 25 LaBr detectors.Each FATIMA detector consists of a cylindrical LaBr3(Ce) crystal (length2 inches, diameter 1.5 inches) coupled with a Hamamatsu R9779 photo mul-tiplier tube with eight dynodes. Each detector was equipped with a leadshield of 4mm thickness around the crystal to avoid detecting γ rays scat-tered from neighbouring detectors.The fast timing system and Digital Gammasphere each took data inde-pendently in their own data stream. DGS on its own accepted events of twoγ rays in coincidence within 2 µs.Fast Timing Measurement Using an LaBr3(Ce) Scintillator Detector . . . 353VME busDetector 1Detector 2Digitizer X6V1751CFD X2V812Logic unitV1495 CFD(ORTEC)DynDynSigSigDelay boxΣ outIn (T)DelOutTDCV1290In x8In x16Trig InMyRIAD V2718PCIn x16NIMStandardLogicUnit 755 In x2Io00Digital GSΣ outVMEStandardTrig InAnalog GS (CFD)Out x16Out x16In x32Coinc cond 2 Out  In Coinc cond 1Out x7 X25ECL to NIM ConvRatemeterCh 4b)Fig. 1. (a) Top view drawing of the LaBr + Gammasphere array. (b) Schematicdrawing of the fast timing data acquisition system. See the text for details.A schematic picture of the LaBr DAQ system is shown in Fig. 1 (b).The signal from the eighth dynode of the LaBr detectors was directly fedinto V1751 digitizers (1GS/s, 10 bit resolution) and provided the energyinformation. The anode signal was directly fed into V812 CFD modules.The constant fraction delay was set to 8 ns. The output was then sent toV1290 TDC modules which provided the time information (25 ps/chn). Inorder to correlate the energy and time data, an event-based data acquisitionis controlled by a V1495 logic unit. In stand-alone operation, the trigger for afast timing event is formed by at least 2 LaBr detectors within 200 ns, usingthe CFD multiplicity output. The event-based readout system currentlyleads to a large read-out dead-time of the order of 300µs. Due to this fact,an additional coincidence with a Gammasphere detector was imposed onthe fast timing event trigger to ensure at least one DGS coincidence for eachtrigger. The coincidence width for this was set to 500 ns.The integration of the two DAQ systems was accomplished by introduc-ing a MyRIAD module [10] into the fast timing part. This module wasconnected to the Digital Gammasphere DAQ by a bidirectional optical fiberto synchronize its clock with the Digital Gammasphere DAQ master clockand to send triggers to Digital Gammasphere. The fast timing trigger de-scribed above was fed into to MyRIAD module, where a time stamp wasgenerated and stored for the event. This time stamp from the MyRIADclock, which was synchronized with the DGS clock, was later used to mergethe two data streams. The fast timing trigger was also sent to the DGSDAQ where it triggered a readout (width of 2µs). This ensured readout ofsingle γ events in DGS which were in coincidence with a fast timing trigger,but not with a multiplicity-two trigger of DGS itself.354 M. Rudigier et al.3. Experiment and state of analysisFirst several tests were made with the sources 152Eu, 60Co, 88Y, and166Ho to verify the proper working of the fast timing part, the integrationwith DGS, and for calibration. The relative energy resolution of the LaBrarray was found to be around 3.7% at 660 keV. The full energy peak singlesefficiency of the 25 detectors, which were positioned 12.4 cm away from thesource, was about 2.5% at 1MeV and about 5% at 500 keV. For the 50 DGSdetectors, this was about 5% and 8% respectively. Figure 2 (c) shows theprompt response distribution of the full array for a prompt cascade in 88Sr(88Y source). The width of a prompt distribution is a measure of the timingresolution of the set-up. The result of FWHM = 343ps is slightly worsebut comparable to what is found in similar experiments for these γ energies,e.g. FATIMA at EXILL [4]. A test with a 166Ho source, decaying to 166Er,showed the capabilities of the fast timing set-up. In the ground state bandof 166Er, according to the NNDC data base [11], the half lives of the first2+, 4+ and 6+ are 1815(23) ps, 118(4) ps, and 15.0(8) ps. We measured the2+ half life with a slope fit, obtaining 1851(30) ps, which agrees well withthe adopted NNDC value. Half lives in the picosecond region were measured0 200 400 600 800 1000 1200 1400PRD [ps]-200-1000100200300400500[keV]E0 200 400 600 800 1000 1200 1400-30-20-100102030a)b)3400-2020406080380 420360 400347.9 ps39.6 psResidual [ps]11010010001000010000048 48.5 49 49.5 50 50.5 51 51.5 52c)FWHM = 343 ps1836-898 keV cascade in 88Srnumber of countsΔt (ns)Fig. 2. (a) Prompt response difference (PRD) of the fast timing array for theexperiment at ANL, measured with transitions from the sources 152Eu, 60Co, and88Y (black dots). The fitted function [12] is shown as a solid line. The delayedcentroid difference values for the 6+ → 4+ → 2+ and the 8+ → 6+ → 4+ cascade(inlay) in the ground state band of 166Er are shown as grey stars. (b) Residual ofthe PRD fit function and the data points used for the fit. (c) Coincidence timespectrum of a prompt cascade measured with an 88Y source.Fast Timing Measurement Using an LaBr3(Ce) Scintillator Detector . . . 355using the generalized centroid difference method (GCD) [12]. This methodis a refinement of the centroid shift method [1]. For the GCD method, thedifference of the centroid positions of the delayed (decay transition gated onstop detector) and anti-delayed (decay transition gated on start detector)time distributions is measured. This value is then two times the lifetime plusa time walk value. The time walk of the system, depending on the energy ofthe start and stop transition, is obtained by measuring the prompt responsedifference (PRD) for the energy range of interest. For this experiment, thePRD was measured using the sources 152Eu, 60Co, and 88Y, see Fig. 2 (a).For the accuracy of the PRD, we adopt a value of 15 ps, see Fig. 2 (b). Thisresults in a lower measuring limit of τ > 8 ps (T1/2 > 6 ps) for the setup.The measured centroid difference values for the 6+ → 4+ → 2+ and8+ → 6+ → 4+ cascade in the 166Er ground state band are shown inFig. 2 (a). These yield the half lives T1/2,4+ = 121(14) ps and T1/2,6+ =14(8) ps respectively, both being consistent with the literature values citedabove. These results demonstrate the general capability of the fast timingsystem to measure half lives from the ns region down to about 10 ps.The 252Cf source was mounted on 18.12.2015 and data were taken forabout five weeks. A typical LaBr singles rate was 2.7 kHz. The DGS doublecoincidence rate was about 13.5 kHz. Here, we show first preliminary resultsfor one of the stronger fission products, 100Zr. Figure 3 (a) shows an LaBrand DGS spectrum, both in triple coincidence with the 6+ → 4+ transitionin 100Zr and the 2+ → 0+ transition in the fission partner 148Ce. Theresult is a quite clean spectrum showing only transitions in the ground stateband of 100Zr and 148Ce. Note that due to the trigger condition on the fasttiming DAQ part, the LaBr spectra are additionally a double LaBr eventprojection. Figure 3 (b) shows the delayed coincidence time spectrum of the4+ → 2+ → 0+ cascade in 100Zr. These spectra were produced with only oneDGS coincidence condition on the 6+ → 4+ transition in 100Zr. Backgroundwas then subtracted from the resulting time distributions to get the showntime spectra. Please note that these results are, therefore, only to be taken asa first measure of the capabilities of the set-up, especially the cited accuraciesare not final. This is mainly the case because the background subtractionis not straightforward in this case and possible systematic errors were nottaken into account. Still it was possible to reproduce the literature valuefrom the nuclear data sheets [13] within the uncertainty, see Fig. 3 (b). Also,two different analysis methods, the fit of a convolution and the GCD method,yield consistent results.356 M. Rudigier et al.50 100 150 200 250 300 350 400 450050100150200250300350400E (keV)FatimaDGS148Ce100Zr2+->0+2+->0+100Zr4+->2+148Ce6+->4+counts200ΔC = 1939(144)psFrom fit : T1/2 = 573(75)psFrom cent. diff : T1/2 = 610(50)psLit. value (NNDC): T1/2 = 590(30)psdecay-feederfeeder-decayFit250 300 350Δt (chn)-50050100150200250countsFig. 3. (a) Coincidence γ-ray spectrum of Digital Gammasphere (DGS) (grey)and LaBr (black). The coincidence condition is a double gate on DGS with the6+ → 4+ in 100Zr (497 keV) and the 4+ → 2+ transition in the fission partner 148Ce(294 keV). (b) Delayed LaBr coincidence time spectra of the 4+ → 2+ → 0+ cascadein 100Zr with a selection gate on the 6+ → 4+ transition in DGS. Background wassubtracted from these spectra. The grey line shows a fit to the data of a convolutionof an exponential decay with a Gauss-shaped prompt response distribution.4. ConclusionIn conclusion, the fast timing part of the experiment produced reliableresults in the source measurements. Coupling with Digital Gammaspherewas done successfully using the MyRIAD interface. The data have been suc-cessfully merged and are in progress of being analysed by the collaboration.It is expected to get results for more weakly produced isotopes by combiningstatistics from several DGS coincidence conditions.Fast Timing Measurement Using an LaBr3(Ce) Scintillator Detector . . . 357In general, it can be said that the coupling of an LaBr array with Gam-masphere is very fruitful. Not only fast timing in the sub-nanosecond regionis feasible with this kind of experiment. At the same time, the LaBr detec-tors can potentially be used for spectroscopy of low-energy transitions, e.g.isomers, for which the Gammasphere detector efficiency is very low.This work was supported by Science and Technology Facilities Council(UK). This material is based upon work supported by the U.S. Departmentof Energy, Office of Science, Office of Nuclear Physics under contract num-ber DE-AC02-06CH11357. This research used resources of ANL’s ATLASfacility, which is a DOE Office of Science User Facility. This work was alsosupported by the Bulgarian National Foundation for Scientific Research un-der grant number DFNI-E02/6. P.H.R. acknowledges partial support fromthe UK National Measurement Office.REFERENCES[1] H. Mach, R.L. Gill, M. Moszyński, Nucl. Instrum. Methods Phys. Res. A280, 49 (1989).[2] P.J. Nolan et al., Rep. Prog. Phys. 42, 1 (1979).[3] F. Browne et al., Acta Phys. Pol. B 46, 721 (2015).[4] J.-M. Régis et al., Nucl. Instrum. Methods Phys. Res. A 763, 210 (2014).[5] S. Lalkovski et al., Acta Phys. Pol. B 47, 637 (2015).[6] Zs. Podolyak et al., Rad. Phys. Chem. 95, 14 (2014).[7] S. Zhu et al., Nucl. Instrum. Methods Phys. Res. A 652, 231 (2011).[8] I-Y. Lee et al., Nucl. Phys A 520, 641c (1990).[9] T.J. Anderson et al., IEEE Nuclear Science Symposium and Medical ImagingConference (NSS/MIC), 6551368 (2012).[10] T.J. Anderson, MyRIAD user manual, ANL, 2015.[11] C.M. Baglin, Nucl. Data Sheets 109, 1103 (2008).[12] J.-M. Régis et al., Nucl. Instrum. Methods Phys. Res. A 726, 191 (2013).[13] B. Singh, Nucl. Data Sheets 109, 297 (2008).

Fast timing measurement using an labr3(Ce) scintillator detector array coupled with gammasphere

https://cdr.lib.unc.edu/downloads/5m60r313h

Fast timing measurement using an labr3(Ce) scintillator detector array coupled with gammasphere

Abstract

Similar works

Full text

Available Versions

Carolina Digital Repository