New technologies have been developed recently that add to the QC option available for auger cast piles. Four transportation applications will be discussed: bridge foundation including abutments, retaining structures (secant or tangent pile walls), column-supported embankments over soft ground, and sound walls. Emphasis will be placed on the installation process, QC during installation, quality assurance after installation, and the common misperceptions. The presentation will include one case history for a 12-floor building in downtown Fort Wayne, Indiana, showing the design for 47 auger cast piles as one group

Smadi, Malek

English

Purdue E-Pubs

Design and Construction of Auger Cast Piles 101th Annual Road School 2015  3/11/2015 Malek Smadi, Ph.D., P.E. Principal Engineer - GEOTILL - Fishers, IN msmadi@geotill.com - www.geotill.com CONTENTS 1. Auger Cast Pile Types 2. Construction Sequence 3. Applications For Transportation Projects    4. Common Materials 5. Construction Equipment 6. Procedures Used In This Technology 7. Static Axial Capacity, Case History 8. Group Effects For Axial Capacity Lateral Load And Settlement, Case History 9. Quality Control (QC)/ Quality Assurance (QA)  Example of Foundations Failure 1 Example of Foundations Failure 2 Example of Foundations Failure 3 Example of Foundations Failure 4 Auger Cast Pile Types Auger Cast Pile (ACP)  Continuous Flight Auger (CFA) Piles Augered-Cast-in-Place (ACIP) Auger Pressure Grout Screw Piles Drilled Displacement (DD) Piles   Auger Cast Pile Types Auger cast piles are a type of drilled foundation in which the pile is drilled to the final depth in one continuous process using a continuous flight auger. Auger Cast Piles Auger Cast Pile Types A) During drilling the flights of the auger are filled with soil, providing lateral support and maintaining the stability of the hole. B) At the same time the auger is withdrawn from the hole, concrete or a sand/cement grout is placed by pumping the concrete/grout mix through the hollow center of the auger pipe to the base of the auger that provides continuous support of the hole. C) Then Steel-reinforcement is placed into the hole. Auger Cast Pile Types Drilled Displacement (DD) Piles Auger Cast Pile Types Auger Cast Pile Types Auger Cast Piles Auger cast piles are typically installed with diameters ranging from 12 to 36 in. and lengths of up to 100 ft.  In Europe with more recent powerful rigs, diameters could go up to 60 in. The reinforcement is in the upper portion of the pile for ease of installation and low bending stresses are transferred below these depths. In some cases, full-length reinforcement is used, as is most common with drilled shaft foundations. Auger cast piles can be constructed as single piles like for soundwall or light pole foundations For bridges or other large structural foundations, auger cast piles are most commonly installed as part of a pile group in a manner similar to that of driven pile foundations  Auger Cast Pile Types Drilled Shaft vs. CFA Foundation Auger Cast Piles Use of casing or slurry to temporarily support the hole is avoided. Drilling the hole in one continuous process is faster than drilling a shaft excavation. Because of torque requirement the diameter and length of CFA piles are generally less than drilled shafts. Continuous auger for installation also limits CFA piles to soil or very weak rock profiles. Auger Cast Pile Types Drilled Shaft vs. CFA Foundation Auger Cast Piles Auger Cast Pile Types Driven Piles vs. CFA Foundation Auger Cast Piles Noise and vibration due to pile driving are minimized. CFA piles eliminate splices and cutoffs. Soil heave due to driving can be eliminated when non-displacement CFA piles are used. A disadvantage of CFA piles compared to driven piles is that the available QA methods to verify the structural integrity and pile bearing capacity for CFA piles are less reliable than those for driven piles. CFA piles generate soil spoils that require collection and disposal especially if it is contaminated. Construction Sequence - Drilling Effect of Over- Excavation using CFA Piles Balanced auger rotation and penetration rates The auger having an excessively slow penetration rate and an insufficient base feed to keep the auger flights full Construction Sequence - Drilling When a soil profile being drilled has mixed soil conditions (e.g., weak and strong layers), difficulties may arise. If the rig cannot penetrate the strong soil stratum at the proper rate, the augers can “mine” the overlying weak soil to the surface and cause subsidence. One solution to properly balance soil removal and penetration rate is to use Drilled Displacement (DD) piles. Construction Sequence - Grouting When the drilling stage is complete and the auger has penetrated to the required depth, the grouting stage must begin immediately. Grout or concrete is pumped under pressure through a hose to the top of the rig and delivered to the base of the auger via the hollow center of the auger stem. Grout Delivered to Pump Construction Sequence - Grouting Hole at Base of Auger for Concrete Construction Sequence – Grouting Sequence Upon achieving the design pile tip elevation, the auger is lifted a short distance typically 6 to 12 in. and grout is pumped under pressure to expel the plug at the base of the internal pipe and commence the flow. The auger is then screwed back down to the original pile tip elevation to establish a small head of grout or concrete on the auger and to achieve a good bearing contact at the pile tip. The grout is pumped continuously under pressure typically up to 150 to 300 psi measured at the top of the auger while the auger is lifted smoothly in one continuous operation. Simultaneously, as the auger is lifted, the soil is removed from the flights at the ground surface so that soil cuttings are not lifted high into the air (potential safety hazard). After the auger has cleared the ground surface and the grouting/concrete procedure is completed, any remaining soil cuttings are removed from the area at the top of the pile and the top of the pile is cleared of debris and contamination. The reinforcement cage is lowered into the fluid grout/concrete to       the required depth and tied off at the ground surface to maintain       the proper reinforcement elevation. Construction Sequence Construction Sequence Sometime the top of the pile can be difficult to find among the surface disturbance. Attention to detail in the final preparation of the surface is critical to ensure that structural integrity is maintained.  Grout at Surface after Auger Withdrawal Construction Sequence Finishing Pile and Reinforcement Placement Construction Sequence - Grout vs. Concrete Concrete Majority of work is using a sand/cement grout mixture because of the fluidity and ease of installation of reinforcement. The typical range of compressive strength of grout (4,000 to 5,000 psi). In the grout mix, fly ash and slag are often substituted for a portion of the cement  for 24% to 30% to produce mixes with higher workability and pumpability, reduced bleeding, and reduced shrinkage. Grout is so fluid that the workability is typically measured using a flow cone. For concrete a pea-gravel size aggregate with around 42% sand used in the mix. Concrete is cited as being less costly than grout, less prone to overrun volume, and is considered to be more stable in the hole when constructing piles through soft ground. Concrete slump for CFA construction is similar to that of wet-hole drilled shaft construction, with target slump values in the 8 in. ± 1 in. range. Grout Applications For Transportation Projects Bridge Piers and Abutments. Soundwalls. Earth Retaining Structures. Pile-Supported Embankments. Advantages And Limitations of CFA Piles  Speed of installation of CFA piles and lower cost over other pile types.  Increased requirements to minimize noise and vibrations from pile installation in heavily populated areas.  A reluctance by many owners to utilize CFA piles because of concerns about quality control and structural integrity.  Demand on bridges for uplift and lateral load capacity, scour  considerations, and/or seismic considerations, require pile diameters and possibly lengths Advantages And Limitations of CFA Piles  Medium to very stiff clay soils. Cemented sands or weak limestone. Medium dense to dense silty sands and well-graded sands. Rock overlain by stiff or cemented deposits. Favorable Geotechnical Conditions Very soft soils. Loose sands under groundwater. Geologic formations containing voids. Hard soil or rock overlain by soft soil or loose, granular soil. Unfavorable Geotechnical Conditions Applications For Transportation Projects  Favorable geotechnical conditions available.  Projects where speed of installation is important.  Batter Piles Required.  Projects where large numbers of piles are required.  Low headroom conditions. When to Select and Use the CFA Piles Applications For Transportation Projects  Bridge Piers and Abutments Types of bridge most suited for the use of CFA  Interchange structures (where scour is not a major issue).  Approach structures.  Or those involving bridge widening. Applications For Transportation Projects  Bridge Piers and Abutments Crosby, Texas Applications For Transportation Projects  Bridge Piers and Abutments Crosby, Texas Twelve production piles were instrumented and monitored during construction and load testing using trucks. The results from the pile instrumentation suggest that the piles supported the fully loaded bridge entirely by mobilizing side friction alone and with very small around 0.1 in. movements. Applications For Transportation Projects  Low Headroom Conditions Applications For Transportation Projects  Secant or Tangent Pile Walls CFA piles can be a viable alternative to drilled shafts or slurry walls.  A structural steel section may be used for pile reinforcement rather than a reinforcing cage.  Needs heavy drilling equipment. Applications For Transportation Projects  Secant or Tangent Pile Walls Applications For Transportation Projects  Drilling CFA Piles for Secant Wall Applications For Transportation Projects  Secant or Tangent Pile Walls New Haven, Connecticut Applications For Transportation Projects  Secant or Tangent Pile Walls New Haven, Connecticut Applications For Transportation Projects  Soundwalls in Favorable Soil Applications For Transportation Projects  Pilecaps on CFA Piles for a Pile-Supported Embankment The use of CFA piles for a pile-supported embankment may represent a cost-effective alternative to ground modification Applications For Transportation Projects  Pilecaps on CFA Piles for a Pile-Supported Embankment Foundation strata consist of weak and compressible subsoils, which would take a long time to consolidate. Accelerating construction. fill supporting a transportation facility that is particularly sensitive to settlements (such as a high-speed rail). Accelerated construction is required for projects where additional cost due to traffic shifts, geotechnical instrumentation, and related time delays present an unacceptable situation to project owners Construction Cost ($20 to $28 per linear foot Costs relating to performance and integrity testing are likely to be higher on transportation projects. Length, diameter, reinforcement, and grout strength. Size of the project. Mobilization cost Many Variables Affect Pile Costs Construction Equipment Crane-Attached CFA System Hydraulic CFA System Construction Equipment Augers for Different Soil Conditions: Auger for CFA Piles in Sandy Soil (Top) and Augers for DD Piles (Bottom) Construction Equipment Auger for Use in Clay, with Auger Cleaner Attachment Construction Equipment Cutter Heads for Hard Material (left) and Soil (right) Construction Equipment Double Rotary CFA Piles Construction Equipment Trucks Discharging into Pump Close up View of Grout Pump Construction Equipment In-Line Flowmeter Construction Equipment Sensor for Concrete Pressure at Auger Tip Reinforcement Machine-Welded Reinforcement Cage on Project Site Reinforcement Use of Steel Pipe to Reinforce a CFA Pile for a Wall Reinforcement Installation of Reinforcement Cage into Battered CFA Pile Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 12 Floors Building in Downtown Fort Wayne, Indiana  Static Axial Capacity and Group Effects, Case History 14 Floors Tower in Downtown Indianapolis, Indiana  Static Axial Capacity and Group Effects, Case History 14 Floors Tower in Downtown Indianapolis, Indiana  Static Axial Capacity and Group Effects, Case History 14 Floors Tower in Downtown Indianapolis, Indiana  Quality Control (QC) / Quality Assurance (QA) Operator with Cab Mounted Display Used to Control Drilling Monitoring and Control of the Drilling Phase The operator and inspector should observe and record the depth of the auger, the speed of the auger, the rate at which the auger penetrates into the ground, and the torque with which the auger is rotated. Quality Control (QC) / Quality Assurance (QA) In-line Flowmeter Monitoring and Control of the Grouting/Concreting Phase Control of the grouting / concreting phase of construction may be the most important aspect of QA/QC for CFA piles. Quality Control (QC) / Quality Assurance (QA) Display Panel for Observation by Inspector Monitoring and Control of the Grouting/Concreting Phase Quality Control (QC) / Quality Assurance (QA) Example Data Sheet from Project Quality Control (QC) / Quality Assurance (QA) Cubes for Grout Testing Quality Control (QC) / Quality Assurance (QA) Integrity Testing by Surface Methods -Sonic Echo Testing   Use of Integrity Testing Quality Control (QC) / Quality Assurance (QA) Integrity Testing using Downhole Techniques  Downhole Single-Hole Sonic Logging (SSL) Concept Use of Integrity Testing Quality Control (QC) / Quality Assurance (QA) Static Load Test Setup on CFA Piles Load Testing Quality Control (QC) / Quality Assurance (QA) Proof Testing of Production Piles with Statnamic Load Testing Questions ? Malek Smadi, Ph.D., P.E. Principal Engineer - GEOTILL - Fishers, IN msmadi@geotill.com - www.geotill.com 

Design and Construction of Auger Cast Piles

https://docs.lib.purdue.edu/cgi/viewcontent.cgi?article=1465&context=roadschool

Design and Construction of Auger Cast Piles

Abstract

Similar works

Full text

Available Versions

Purdue E-Pubs