In the future active network management and protectionsolutions have to enable utilization of intended islandoperation as well as active control and utilizationflexibilities during normal and islanded operation ofgrid interactive microgrids. In this paper, combinedislanding detection schemes for both MV and LVnetwork connected distributed generation units duringnormal grid-connected operation are studied.Utilization of active network management functionalityat MV level enables to control the reactive powerunbalance continuously in order to ensure reliableislanding detection without non-detection zone.Combined scheme also prevents maloperations due toother disturbances.fi=vertaisarvioitu|en=peerReviewed

Hovila, Petri

Kauhaniemi, Kimmo

Laaksonen, Hannu

Sirviö, Katja

English

Osuva

CIREDWorkshop Proceedings : Microgrids and Local Energy Communities,Ljubljana, Slovenia, June 7-8, 2018CIRED Workshop -  Ljubljana, 7-8 June 2018Paper 0056Paper No  0056 Page 1 / 4ADVANCED ISLANDING DETECTION IN GRID INTERACTIVE MICROGRIDS                                      Hannu LAAKSONEN                                               Petri HOVILA                          Kimmo KAUHANIEMI, Katja SIRVIÖ                           ABB Oy – Finland                                 University of Vaasa – Finland                                 petri.hovila@fi.abb.com                                 hannu.laaksonen@univaasa.fiABSTRACTIn the future active network management and protectionsolutions have to enable utilization of intended islandoperation as well as active control and utilizationflexibilities during normal and islanded operation ofgrid interactive microgrids. In this paper, combinedislanding detection schemes for both MV and LVnetwork connected distributed generation units duringnormal grid-connected operation are studied.Utilization of active network management functionalityat MV level enables to control the reactive powerunbalance continuously in order to ensure reliableislanding detection without non-detection zone.Combined scheme also prevents maloperations due toother disturbances.INTRODUCTIONIn the future, active utilization of controllable, flexible,distributed energy resources, DER, like distributedgeneration, energy storages, controllable loads/demandresponse, intelligent charging of electric vehicles will bein key role to enable more resilient power system. Inaddition, new cost-efficient, reliable, standardized andredundant solutions for future resilient power systemmust utilize possibilities of advanced ICT technologies(like wireless 5G and cloud servers with smart big data-analytics) and have cyber-security integrated in allsolutions.Electricity distribution network areas with DER, i.e.FlexZones [1] or nested, grid interactive microgridscould be seen as resilient power system building-blocks.Intelligent and coordinated use of microgrids’flexibilities between distribution and transmissionsystem operators (DSOs and TSOs) for differenttechnical services enables realization of improved localand system-wide grid resiliency in the future duringnormal grid interactive operation mode. Duringtransmission or distribution network downtimes due tostorms, natural disasters or external attacks (physical orcyber) microgrid with flexibilities can still continueelectricity supply to customers in islanded operationmode.Grid-code compatible, combined islanding detectionschemes (e.g. high-speed communication based transfertrip through optical fibre / wireless 5G, like IEC 61850-based GOOSE or routable R-GOOSE message & faultdetection/direction + voltage vector shift, VVS) (Fig. 1)are needed in the future. With resilient combinedscheme maloperation due to other network events canbe avoided, non-detection zone (NDZ) can beminimized, prioritization issues with DG unit grid coderequirements can be avoided and ENTSO-E RfGrequirement (not only status position detection) can befulfilled. Utilization of active network management(ANM) functionality at MV level enables to control thereactive power unbalance Qunb continuously in order toensure islanding detection of the passive method (likeVVS with sensitive settings) in the combined schemewithout NDZ (Fig. 1). Realization of future-proof andgrid code compatible schemes requires studies regardingdependencies between protection, islanding detectionand ANM functionalities. [1]-[7]Figure 1. a) Combined islanding detection scheme, b) grid codecompatible ANM scheme able to fulfill multiple targetssimultaneously (see Fig. 2) and c) Dependencies between networkstatus, protection, islanding detection & ANM functionalities andissues related to intended islanding operation prioritization.In this paper, combined islanding detection schemes(Fig. 1) for both MV and LV network connected DGunits during grid-connected operation are studied byPSCAD simulations with model from Sundom SmartCIRED Workshop -  Ljubljana, 7-8 June 2018Paper 0056Paper No  0056 Page 2 / 4Grid (SSG) which is a local smart grid pilot in Vaasa,Finland (Fig. 2). The focus is on such scheme (Fig. 1)which, in addition to other simultaneous Qflow & U -management targets (Fig. 1), utilizes reactive powerunbalance control based Qflow & U -management ANMscheme to ensure reliable islanding detection. Thepurpose is also, as part of the combined islandingdetection scheme, that the fault location could be takenintelligently into account by fault detection/directioninformation from primary and secondary substations.Depending on the fault location, DG units inside faultednetwork section will be disconnected (faulty island) andDG units outside faulted section would not beunnecessarily disconnected (Fig. 1). The DG unitsoutside the faulted section could then be used forimproving local or system-wide grid resiliency throughFRT, P/f- or Q/U -control or intentional island operationdepending on the fault location, power balance situationetc. before fault, prioritization as well as allowance ofintended island operation (Fig. 1).Today there are two DG units connected to SSG (Fig.2). One full-power-converter based wind turbine (3.6MW) connected to MV network with own MV feederJ08 (Fig. 2) and another LV network connected inverterbased PV unit (33 kW) at MV/LV substation TR4318(Fig. 2).Figure 2. Sundom Smart Grid (SSG) in which ANM and islandingdetection presented in Fig. 1 will be studied.Islanding detection (Fig. 1a) is one of the multipletargets of the studied and developed ANM scheme (Fig.1b). The ANM scheme target limits which need to befulfilled can be studied in two different cases (Fig. 3). Incase 1 Fingrid’s (Finnish TSO) ‘reactive powerwindow’ (which is requirement today) is used to set thelimits for reactive power exchange between distributionnetwork and transmission network at SSG HV/MVsubstation (Fig. 3a). The ENTSO-E NC for demandconnection (DC) [8] (future requirement) is used to setthese same limits in case 2 (Fig. 3b).Figure 3. a) In case 1 Fingrid’s ‘reactive power window’ and b) incase 2 ENTSO-E NC for demand connection (DC) [8] is used to setthe limits for reactive power exchange between distribution networkand transmission network at SSG HV/MV substation (Fig. 2) as partof the studied ANM scheme (Fig. 1b).SIMULATION CASES AND RESULTSIn the following PSCAD simulation results fromislanding detection simulations in SSG (Fig. 2) duringgrid-connected operation are presented. The simulationstudies purpose for this paper was to focus on thedevelopment of primary combined islanding detectionschemes [5] shown in Fig. 1 (i.e. high-speedcommunication based transfer trip & faultdetection/direction + 1°-2° VVS). From combinedislanding detection (Fig. 1) operation speed point ofview it matters to some extent (communication latency)in which point VVS detection is made (see Fig. 2).Islanding can be detected most rapidly if VVS isdetected at the connection point of the DG unit. Alsofrom back-up islanding detection scheme point of view,local VVS and fault detection [5] at connection point isbeneficial. However, fault detection information fromthe opened CB (which sends islanding detection transfertrip signal) should include also healthy or faulty islanddetection information (Fig. 1) [5]. Many differentislanding detection scenarios were simulated with andwithout fault before islanding (fault locations are shownin Fig. 2). In following some chosen cases arepresented. In all simulations MV islanding occurs at t =3.6 s by opening of CB J05 (Fig. 2).Healthy islanding detection simulations withoutfaultFig. 4 shows MV and LV network primary islandingdetection schemes for wind turbine and PV unit (Fig. 2)during grid-connected operation of SSG in healthyislanding detection cases without fault. In Fig. 5 and 6frequency, positive sequence voltage (U1) and VVSseen by the primary islanding detection scheme of MVnetwork DG unit (wind turbine) and LV network DGunit (PV) during grid-connected operation of SSG (Fig.2) in different healthy islanding detection cases withoutfault (see Fig. 4) are presented. In Fig. 5 six differentcases are shown in which wind turbine control mode isCIRED Workshop -  Ljubljana, 7-8 June 2018Paper 0056Paper No  0056 Page 3 / 4not changed after islanding at t = 3.6 s and active powerunbalance also is not zero before islanding.Respectively, in Fig. 6 four different cases are presentedfrom cases where active power unbalance is nearly zerobefore islanding and wind turbine control mode ischanged after islanding when VVS value is more than 1or 2 degrees.Figure 4. a) MV network DG unit (wind turbine) and b) LV networkDG unit (PV) primary islanding detection scheme during grid-connected operation of SSG (Fig. 2) in healthy islanding detectioncases without fault.Figure 5. Frequency, positive sequence voltage and VVS of MVnetwork DG unit (wind turbine) during grid-connected operation ofSSG (Fig. 2) in 6 different healthy islanding detection cases withoutfault (see Fig. 4), without wind turbine control mode change andislanding at t = 3.6 s.From simulation results (Fig. 5) it can be seen that fast,in less than 100 ms, islanding detection can be achievedwith proposed combined scheme (Fig. 1) and 2° VVSsetting in all cases except in case 4.Figure 6. Frequency, positive sequence voltage and VVS of LVnetwork DG unit (PV) during grid-connected operation of SSG (Fig.2) in 4 different healthy islanding detection cases without fault (seeFig. 4), with wind turbine control mode change and islanding at t = 3.6s.Fig. 6 shows that MV network connected wind turbinecontrol mode should be changed after islanding whenVVS value is more than 2 degrees in order to enable theoperation of LV network DG unit (PV) combinedislanding detection scheme with 2° VVS setting in allcases.SSG with parallel MV feeder fault - No faultyislandingIn Fig. 7 MV network primary islanding detectionschemes for wind turbine (Fig. 2) with NORMALprioritization during grid-connected operation of SSG infaulty islanding detection cases with MV fault atparallel (J06) or same (J08) MV feeder are presented.When there is MV fault at parallel MV feeder (J06 inFig. 7), no faulty islanding by opening of J05 CB shouldhappen. Preventing blocking signal should be sent fromJ06 IED to J05. In general, in both MV fault relatedcases in Fig. 7 HIGH prioritization (Fig. 1c) should beonly possible in case of upstream faults i.e. nodirectional over-current (DOC) starting/detectionsimultaneously. Fig. 8 and 9 present the simulationresults from cases with MV fault at the parallel (J06)MV feeder i.e. no faulty islanding. Fig. 9 shows positiveand negative sequence current magnitudes and angledifferences seen in different points by respective IEDs(J05, J06, J07 and J08) during 3- or 2-phase fault at theparallel (J06) MV feeder.CIRED Workshop -  Ljubljana, 7-8 June 2018Paper 0056Paper No  0056 Page 4 / 4Figure 7. MV network DG unit (wind turbine) primary islandingdetection scheme during grid-connected operation of SSG (Fig. 2) infaulty islanding detection cases with MV fault (NORMALprioritization) at parallel (J06) MV feeder.Figure 8. Frequency, positive sequence voltage and VVS of MVnetwork DG unit (wind turbine) primary islanding detection schemeduring grid-connected operation of SSG (Fig. 2) in 3 different caseswith parallel (J06) MV feeder fault (NORMAL prioritization) 100 msbefore islanding at t = 3.6 s (see Fig. 7).Figure 9. Positive and negative sequence current magnitudes (I1_magand I2_mag) as well as U1_angle-I1_angle and U2_angle-I2_angle during grid-connected operation of SSG (Fig. 2) in 2 different no faulty islandingdetection cases with MV fault (NORMAL prioritization) at theparallel (J06) MV feeder 100 ms before islanding at t = 3.6 s (see Fig.7).From Fig. 9 simulation results it can be seen how windturbine negative sequence current injection during 2-phase fault affects on the angle seen by MV feeder J08IED.CONCLUSIONSThis paper presented successful simulations ofcombined islanding detection schemes for both MV andLV network connected DG units during grid-connectedoperation. Islanding detection is one of the multipletargets of the studied ANM scheme and Fig. 10 showsthe initial ANM scheme control limits in SSG based onthe islanding detection simulations.Figure 10. Accurate studied ANM scheme (Fig. 1b) control limits inSSG (Fig. 2) for a) case 1 Fingrid’s ‘reactive power window’ and b)case 2 ENTSO-E NC for demand connection (DC) [8] (see Fig. 3).AcknowledgmentsThis work was supported by DeCAS project(http://www.decas-project.eu/), which has receivedfunding from the joint EU program initiative ERA-NetSmart Grids Plus (http://www.eranet-smartgridsplus.eu/).REFERENCES[1] H. Laaksonen, P. Hovila, 2016, “FlexZone Concept to EnableResilient Distribution Grids – Possibilities in Sundom Smart Grid”,CIRED 2016 Workshop, Helsinki, Finland[2] H. Laaksonen, K. Kauhaniemi, S. Voima, 2011, “MicrogridVoltage Level Management and Role as Part of Smart Grid VoltageControl”, PowerTech 2011, Trondheim, Norway.[3] H. Laaksonen, 2016, “Need for New Islanding Detection Schemesand Prioritization with Generator Grid Code Requirements”,International Review of Electrical Engineering (IREE), vol. 11, 160-170.[4] H. Laaksonen, 2016, “Grid code compatible islanding detectionschemes using traditional passive methods”, DPSP 2016, Edinburgh,Scotland, UK[5] H. Laaksonen, P. Hovila, 2017, “Future-proof Islanding DetectionSchemes in Sundom Smart Grid”, 24th International Conference onElectricity Distribution (CIRED 2017), Glasgow, Scotland.[6] H. Laaksonen, 2014, “Reliable Islanding Detection with ActiveMV Network Management”, CIRED Workshop 2014, Rome, Italy.[7] H. Laaksonen, 2014, “Securing Passive Islanding Detection andEnabling Stable Islanding with Q/f -droop Control of DG Unit”,International Review of Electrical Engineering (IREE), vol. 9, 592-602.[8] ENTSO-E, 2012, ENTSO E Network Code on Demand Connection(NC DC).

Advanced islanding detection in grid interactive microgrids

https://osuva.uwasa.fi/bitstream/handle/10024/11249/Osuva_Laaksonen_Hovila_Kauhaniemi_Sirvi%c3%b6_2018_0056.pdf?sequence=2&isAllowed=y

Advanced islanding detection in grid interactive microgrids

Abstract

Similar works

Full text

Available Versions

Osuva