The first step of the development of a new data acquisition system for the Water Cherenkov detectors used within LAGO Collaboration is described. The system is based in the open source board Red Pitaya; design and development of a prototype of the interface board needed to connect peripherals (PMTs and sensors) as well as power supply is described. First tests of functionality connecting the PMT that will be used to implement a WCD detector in USFQ Cumbayá Campus are reported. Future development in HW and SW in order to have a new data acquisition system for particle detection is described.Se describen los primeros pasos para el desarrollo de un nuevo sistema de adquisición de datos para los detectores de agua Cherenkov usados en la Colaboración LAGO. El sistema se basa en la tarjeta de código abierto Red Pitaya; se describe también el diseño y la implementación de un primer prototipo de tarjeta de interfaces para conectar todos los periféricos necesarios (PMTs y sensores) así como los módulos de alimentación. Se reportan las primeras pruebas de funcionamiento conectando el PMT que será usado para implementar un detector WCD en el Campus Cumbayá de la USFQ. Se describen además los desarrollos futuros de SW y HW necesarios para completar el diseño de un nuevo sistema de adquisición de datos para detección de partículas

Ramos Cisneros, Marco Andrés

BIBLIOTECA USFQ

UNIVERSIDAD SAN FRANCISCO DE QUITO USFQColegio de Ciencias e IngenieríasDiseño de un nuevo sistema de adquisición basado en RedPitaya para los detectores de partículas usados en lacolaboración LAGOProyecto de investigaciónMarco Andrés Ramos CisnerosIngeniería ElectrónicaTrabajo de titulación presentado como requisitopara la obtención del título deIngeniero ElectrónicoQuito, 16 de mayo de 20162UNIVERSIDAD SAN FRANCISCO DE QUITO USFQCOLEGIO CIENCIAS E INGENIERÍASHOJA DE CALIFICACIÓNDE TRABAJO DE TITULACIÓNDiseño de un nuevo sistema de adquisición basado en RedPitaya para los detectores de partículas usados en lacolaboración LAGOMarco Andrés Ramos CisnerosCalificación:Nombre del profesor, Título académico Dennis Cazar Ramirez, Ph.D.Firma del profesor ________________________________Quito, 16 de mayo de 20163Derechos de AutorPor medio del presente documento certifico que he leído todas las Políticas yManuales de la Universidad San Francisco de Quito USFQ, incluyendo la Política dePropiedad Intelectual USFQ, y estoy de acuerdo con su contenido, por lo que los derechos depropiedad intelectual del presente trabajo quedan sujetos a lo dispuesto en esas Políticas.Asimismo, autorizo a la USFQ para que realice la digitalización y publicación de estetrabajo en el repositorio virtual, de conformidad a lo dispuesto en el Art. 144 de la LeyOrgánica de Educación Superior.Firma del estudiante: _______________________________________Nombres y apellidos: Marco Andrés Ramos CisnerosCódigo: 00127964Cédula de Identidad: 171588462-1Lugar y fecha: Quito, mayo de 20164RESUMENSe describen los primeros pasos para el desarrollo de un nuevo sistema de adquisición dedatos para los detectores de agua Cherenkov usados en la Colaboración LAGO. El sistema sebasa en la tarjeta de código abierto Red Pitaya; se describe también el diseño y laimplementación de un primer prototipo de tarjeta de interfaces para conectar todos losperiféricos necesarios (PMTs y sensores) así como los módulos de alimentación. Se reportanlas primeras pruebas de funcionamiento conectando el PMT que será usado para implementarun detector WCD en el Campus Cumbayá de la USFQ. Se describen además los desarrollosfuturos de SW y HW necesarios para completar el diseño de un nuevo sistema de adquisiciónde datos para detección de partículas.Palabras Clave. Detección de partículas, Detectores Cherenkov, FPGA, Red Pitaya,Sistema de adquisición de datos, fotomultiplicadores.5ABSTRACTThe first step of the development of a new data acquisition system for the Water Cherenkovdetectors used within LAGO Collaboration is described. The system is based in the opensource board Red Pitaya; design and development of a prototype of the interface boardneeded to connect peripherals (PMTs and sensors) as well as power supply is described. Firsttests of functionality connecting the PMT that will be used to implement a WCD detector inUSFQ Cumbayá Campus are reported. Future development in HW and SW in order to have anew data acquisition system for particle detection is describedKeywords. Particle detection, Cherenkov detectors, FPGA, Red Pitaya, Data acquisitionsystem, Photomultiplier6TABLA DE CONTENIDOMethods and Materials.............................................................................................................8Overview of the data acquisition system for a WCD...................................................................... 8The Red Pitaya board........................................................................................................................ 9Leopard Interface Board.................................................................................................................10Results......................................................................................................................................11Test of functionality and first attempt to collect data...................................................................11Test with PMT attached.................................................................................................................. 12Conclusions..............................................................................................................................13Acknowledgments................................................................................................................... 14References................................................................................................................................147AVANCESEN CIENCIAS E INGENIERÍASARTICULO/ARTICLE SECTION/SECCIÓNDesign of a new data acquisition system based on Red Pitaya for particle detectors usedby the LAGO CollaborationMarco Ramos Cisneros (1) (2), Dennis Cazar Ramírez (1) (2) , Edgar Carrera (1) (2)(1) Universidad San Francisco de Quito USFQ, Colegio de Ciencias eIngenierías “El Politécnico” Campus Cumbayá, edificio. Maxwell oficina. M105D,Casilla Postal 17-1200-841 Quito EcuadorE-mail: mramos@estud.usfq.edu.ec(2) The Latin American Giant Observatory (LAGO), http://lagoproject.org, see the full list ofmembers and institutions at http://lagoproject.org/collab.htmlEditado por/Edited by:Recibido/Received: . Aceptado/Accepted: .Publicado en línea/Published on Web: . Impreso/Printed:AbstractThe first step of the development of a new data acquisition system for the Water Cherenkov detectors used within LAGOCollaboration is described. The system is based in the open source board Red Pitaya; design and development of a prototypeof the interface board needed to connect peripherals (PMTs and sensors) as well as power supply is described. First tests offunctionality connecting the PMT that will be used to implement a WCD detector in USFQ Cumbayá Campus are reported.Future development in HW and SW in order to have a new data acquisition system for particle detection is describedKeywords. Particle detection, Cherenkov detectors, FPGA, Red Pitaya, Data acquisition system, PhotomultiplierResumenSe describen los primeros pasos para el desarrollo de un nuevo sistema de adquisición de datos para los detectores de aguaCherenkov usados en la Colaboración LAGO. El sistema se basa en la tarjeta de código abierto Red Pitaya; se describetambién el diseño y la implementación de un primer prototipo de tarjeta de interfaces para conectar todos los periféricosnecesarios (PMTs y sensores) así como los módulos de alimentación. Se reportan las primeras pruebas de funcionamientoconectando el PMT que será usado para implementar un detector WCD en el Campus Cumbayá de la USFQ. Se describenademás los desarrollos futuros de SW y HW necesarios para completar el diseño de un nuevo sistema de adquisición de datospara detección de partículas.Palabras Clave. Detección de partículas, Detectores Cherenkov, FPGA, Red Pitaya, Sistema de adquisición de datos,fotomultiplicadores.IntroductionWater Cherenkov Detectors WCDs implemented in the LAGO Project are used to detect astroparticles at ground level usingthe “single particle” technique [1]. AWCD is divided into three main components: a pure water tank[2] isolated form naturallight where Cherenkov effect takes place, a photomultiplier sensor PMT which converts Cherenkov radiation into electricimpulses [3]. This electric impulses or “signals” are amplified, digitized and pre-processed by a set of electronic boards, adigitizer board developed within the LAGO Collaboration and a commercial FPGA board for pre-processing and control [4]A commercial PC is then used to storage data files containing absolute time, atmospheric pressure and temperature as well assignals.The key features of this system are the low budget needed to build a detector, the reliability and versatility. Unfortunately theFPGA board used (Digilent Nexys 2 FPGA board) is now discontinued making very difficult and expensive to maintain8WCDs already installed and implement new detectors systems as stated in the LAGO Collaboration development plan [5].After discussions within the Electronics group of the Collaboration it has been decided to select a new commercial board toreplace Nexys 2 in order to speed up the development process rather to design a FPGA board from scratch. Red Pitaya[6], anopen-source-software measurement and control tool, has been chosen due to its low price, high performance and versatility.Present article describes a new data acquisition system based on Red Pitaya Board, the contents of the article is the following:overview of the data acquisition system, a brief description of Red Pitaya board, a description of the interface board“Leopard” designed to connect several peripherals to Red Pitaya, firsts test of control and acquisition of signals from thePMT that will be used to implement the WCD detector “Panchito” in the Cumbayá Campus of USFQ.Circuit design, development test and characterization has been made at “Laboratorio de Partículas Astroparticulas yRadiaciones LEOPARD” of Universidad San Francisco de Quito.METHODS AND MATERIALSOverview of the data acquisition system for a WCDElectrical signals arriving from PMT are negative pulses of hundreds of millivolts and hundreds of nanoseconds length,Figure 1 shows a typical PMT pulseFigure 1 PMT pulse from Photonis XP1805 acquired with a digital oscilloscopeThis signal is amplified, inverted and digitized using a digitizer board developed by the LAGO Collaboration, after the signalis digitized a FPGA preprocess and store the information in a file, a trigger module and a baseline compensation isimplemented in order to improve Signal to Noise Ratio. This board also generates all the supply voltages (12V, 5V, +3.3V, -3.3V) that PMT needs to operate as well as the control voltage to set the level of the high voltage power supply of thePMT[4]. Figure 2 shows a schematic of the board9Figure 2 Block diagram of LAGO DAQ system, the system can acquire signal from 3 PMTs, GPS and temperature &pressure sensors are used to off line correction of data. Data is transferred to a local PC for storage and backup.The main characteristics of the digitizer board are:◆ 3 50ΩAnalog Input Channels ± 2V Input range◆ 3 FADCs 10 bits 40MSPS AD9203A from Analog Devices◆ 1 DAC 12 bits MAX5051 from Maxim◆ High Voltage supply control signals (3 channels) from 0 to 2.5V (PWM signals)◆ 12V, 5V, 3.3V and -3.3V voltage suppliesThe main characteristics of the FPGA board are◆ Xilinx Spartan-3E FPGA 500K gate◆ 16 MB fast Micron® PSDRAM◆ Hirose FX2 (used to connect to digitizer board)◆ Four 12-pin Pmod connectors (used to connect sensors)The Red Pitaya boardRed Pitaya is an open-source-software measurement and control tool [6], it follows a block diagram of the board and list ofmain characteristicsFigure 3 Red Pitaya block diagram [6], besides a FPGA it contains two signal acquisition channels, an ARM μP, USB,Ethernet, I2C communication ports and SD card bay.The main characteristics of the Red Pitaya board are listed, focusing in the most important for our application◆ 2 1MΩ analog input channel ±1V voltage range◆ 2 FADC 14 bits 125MSPS10◆ Xilinx ZC7Z010 System On Chip which contains 2 ARM 9 uP, Artix 7 28K FPGA◆ I2C, SPI, RS232 interfaces◆ 16 GPIO digital pins◆ 8 slow ADC outputs◆ SD Card slot◆ USB and Ethernet portAll these features makes the Red Pitaya not only an ideal replacement on the FPGA for particle detectors but a novel platformto develop every kind of data acquisition system. In particular in our case we can reduce the present DAQ system (PC, NexysII and digitizer board) into two boards: Red Pitaya and an interface board.It follows a detailed description of the interface board needed to implement all the features that a Data acquisition system forLAGOWCD must have.Leopard Interface BoardIn order to replicate the functionalities of the original data acquisition system a “daughter board” has been developed. Thisboard should implement◆ Power supply block: All the voltages needed to power the PMT base, the sensors and the Red Pitaya itself must begenerated from a single 12VDC power supply◆ Slow control block: In order to generate a slow voltage control to High Voltage power supply of the PMT.◆ I2C connection bus: to connect sensors (GPS, temperature & pressure, etc)◆ 2 PMT connections: supply & control voltages, HV read signal and PMT temperature signalFigure 4 Block diagram of the "Leopard" Interface board, in the prototype version the power supply modules are notimplemented, an external power supply is used, only -3.3V is generated in the board.Two signals from PMT are connected to Red Pitaya:◆ HVF: this is a voltage signal (0 – 2.5V) that senses the actual value of high voltage applied to PMT. This signal willbe used to implement a control loop to monitor and correct high voltage value. To avoid high voltage derives iscrucial to maintain WCD well calibrated.◆ AD592: this is a temperature sensor current signal that can be used to monitor temperature inside de water tank.This signal will be used to off-line data correction.Using the I2C, SPI and UART communication interface several sensors can be connected. To replicate the functionalities ofthe present DAQ system a GPS (Venus GPS) and a Temperature&Pressure sensor (BMP180) are used.◆ GPS sensor is connected for synchronization purposes; Venus GPS generates a PPS (Pulse Per Second) signal usedto attach a time stamp in the data file.11◆ Temperature and atmospheric pressure data from BMP180 sensor are attached to data file too for off-line datacorrection.Studies of solar physics and space weather [7] can also be performed analyzing data from detectors, in order to haveenvironmental data to complement particle detector other sensors are planned to be connected to de DAG system, i.e.:◆ Luminosity sensor: to monitor total light flux (Solar physics applications)◆ Accelerometer sensor: to monitor vibrations of the surface (Geophysics applications)◆ Magnetometer sensor: to monitor magnetic field strength (Space Weather applications)Since I2C interface allows connecting up to 127 devices, the ones listed above are only an example. Adding other sensor canallow DAQ system to act as an enhanced weather station [8].RESULTSTest of functionality and first attempt to collect dataPrototype of the DAQ system was tested in two different phases: with a test bench and with the PMT.Test Bench Test: The test bench used is shown in figure 5Figure 5 Block Diagram of the test bench used. Signal generator is used to generate a typical PMT pulse, Oscilloscope isused to visualize HV voltage control. Local PC is used to program Red Pitaya and visualize data.HV Control signal Test: A 0 -1.8V PWM signal is generated by Red Pitaya, Leopard board includes a scaler circuit whichamplifies the original signal to achieve HV power supply voltage control range (0 -2.5V)Figure 6 Yellow line is the PWM signal generated by Red Pitaya, voltage ramp should be 5 seconds long to avoid PMTdamage. Green line is the output of Leopard boardRed Pitaya +Leopard board80 MHzSignalGenerator200 MHzOscilloscopeExternal PowerSupplyLocal PC12Since PMT high voltage supply operates from 0 to 2500 V, HV control signal must be a slow ramp (typical 5 seconds) toavoid PMT damage. Figure 6 shows the behavior of the control signals which complies with specifications.Figure 7 shows a first acquisition attempt using a pulse generated by signal generatorFigure 7 Acquisition of a periodical signal generated with a signal generator. Y axes is in volts, X axes is in ADC stepsTest with PMT attachedFigure 8 shows the test bench used for the following testFigure 8 Test bench used to characterize PMT. Digital voltmeter monitors HV level measured at PMT baseA Photonis 9” PMT with control base designed for the Auger Collaboration [9] was used to test the DAQ system. A HVsignal of 1.8V corresponding to 1890 V was generated. Figure 9 and 10 shows that the DAQ system can acquire all the PMTsignal inside the data buffer without loss of data or superposition.Red Pitaya +Leopard board9” XP1805Photonis PMTDigitalVoltmeterExternal PowerSupplyLocal PC13Figure 9 Capture of an actual PMT signal; HV = 1890V and trigger set to 150 mVFigure 10 Acquisition of PMT signal with HV = 1890V and trigger set to 300mV, each sample is 300ns longCONCLUSIONS◆ Present work shows that a new DAQ system for particle detection based on Red Pitaya is a valid alternative to newgeneration of electronics for WCD of the LAGO Collaboration.◆ With the DAQ system as it is now a PMT characterization procedure can be development. HV voltage can bemonitored and data can be acquired with different levels of trigger.◆ DAQ system was programmed used C++ language, no substantial modifications were made in the FPGA codeproving the easy to use feature of the system.◆ Using Ethernet interface the DAQ system can be accessed without a physical connection, data download, monitorand reprogramming of the DAQ system can be performed in remote way, making the system ideal to develop astand-alone WCD which can be installed in difficult access points like top of mountains or other places at highaltitude14◆ With only SW modifications the DAQ system can be used to acquire signals from other types of particle detectors,in particular Leopard Lab is interested into explore SiPMs (Silicon Photomultipliers) technology to implement ahybrid version of WCDACKNOWLEDGMENTSPresent work was founded by Red CEDIA trough grant CEPRAIX-2015-04- Astropartículas.Authors want to thanks “Colegio de Ciencias e Ingenierías” of Universidad San Francisco de Quito for the constant support.REFERENCES[1] S. Vernetto, Detection of gamma-ray bursts in the 1-GeV to 1-TeV energy range by ground based experiments.Astropart. Phys., 13 (2000), pp. 75–86 (Vernetto, 2000)[2] R. Quishpe, et al for the LAGO Collaboration, “Panchito”Water Cherenkov Detector Water Studies for the LAGOCollaboration, Nuclear and Particle Physics Proceedings, Volumes 267–269, October–December 2015, Pages 433–435[3] C. Mantilla , M. Audelo , M. Calderón , E. Carrera, D. Cazar, O. Martínez, R. Quishpe, S. Vargas, N. Vásquez, forthe LAGO Collaboration, Implementing a WCD detector system in Ecuador as part of the LAGO Project Nuclearand Particle Physics Proceedings. Volumes 267–269, October–December 2015, Pages 430–432[4] M. Sofo Haro, L HArnaldi , for the LAGO Collaboration, The Data Acquisition system of the Latin AmericanGiant Observatory (LAGO), Nuclear Instruments and Methods in Physics A, Volume 820 (2016) pp 34-39[5] The LAGO Collaboration, The Latin American Giant Observatory: Contributions to the 34th International CosmicRay Conference (ICRC 2015), Instrumentation and Methods in Astrophysics, arXiv:1605.02151[6] M. Ossmann, Red Pitaya Not just a USB scope module, Elektor magazine, (2014)https://www.elektormagazine.com/assets/upload/files/EN2014120381.pdf[7] Y.Perez for the LAGO Collaboration, Aplicación en meteorologı́a espacial de los datos del proyecto LAGO (LatinAmerican Giant Observatory), http://hdl.grnet.gr:8002/11456/LAGO-27411[8] J. Peña et al for the LAGO Collaboration, The Guane Array of the LAGO Project Contributions to the 34thInternational Cosmic Ray Conference (ICRC 2015), Instrumentation and Methods in Astrophysics,arXiv:1605.02151[9] Pier Auger Collaboration website, https://www.auger.org/

Diseño de un nuevo sistema de adquisición basado en Red Pitaya para los detectores de partículas usados en la colaboración LAGO

http://repositorio.usfq.edu.ec/bitstream/23000/5154/1/124613.pdf

Diseño de un nuevo sistema de adquisición basado en Red Pitaya para los detectores de partículas usados en la colaboración LAGO

Abstract

Similar works

Full text

Available Versions

BIBLIOTECA USFQ