Wei-Wen Yu Center for Cold-Formed Steel Structures

English

Missouri University of Science and Technology (Missouri S&T): Scholars' Mine

Missouri University of Science and Technology Scholars' Mine CCFSS Technical Bulletins Wei-Wen Yu Center for Cold-Formed Steel Structures 01 Aug 1999 CCFSS Technical Bulletin August 1999 Wei-Wen Yu Center for Cold-Formed Steel Structures Follow this and additional works at: https://scholarsmine.mst.edu/ccfss-technical_bulletins  Part of the Structural Engineering Commons Recommended Citation Wei-Wen Yu Center for Cold-Formed Steel Structures, "CCFSS Technical Bulletin August 1999" (1999). CCFSS Technical Bulletins. 2. https://scholarsmine.mst.edu/ccfss-technical_bulletins/2 This Technical Report is brought to you for free and open access by Scholars' Mine. It has been accepted for inclusion in CCFSS Technical Bulletins by an authorized administrator of Scholars' Mine. This work is protected by U. S. Copyright Law. Unauthorized use including reproduction for redistribution requires the permission of the copyright holder. For more information, please contact scholarsmine@mst.edu. Vol. 8, No. 2CCFSS Technical BulletinAugust 1999PREVIEW OF THE AISI SUPPLEMENT TO THE1996 EDITION OF THE SPECIFICATIONSince 1997, the AISI Committee on Specifications for the Design of Cold-Formed Steel Structural Members has approveda number of new and/or revised design provisions to reflect the results of continuing research.  These approved revisions will bepublished by AISI in a Supplement following the public review.  Changes to the AISI Specification are briefly discussed in thefollowing sections:Section A3.1 - Applicable SteelsReferences for all ASTM standards were updated.  Standard specifications for A847 and A875 steels were added to the list.Section A3.3 - DuctilityEditorial changes were made in Section A3.3.2.  Design equations were added for determining the reduced yield point forcomputing the section strength of multiple-web sections.Section A5.1.3 - Wind or Earthquake LoadsThe exception clause for evaluating diaphragms was deleted from this Section.Section A9 - Reference DocumentsReferences to all documents were updated.  Specifications for A847 and A875 steels were added to the listed ASTM Standards.Section B1.1 - Flange Flat-Width-to-Thickness ConsiderationsThe conditions for some w/t limits for stiffened and unstiffened compression elements were revised.Section B2.4 - C-Section Webs with Holes Under Stress GradientThis is a new section dealing with C-sections having webs with openings.  These provisions can be used within the given limits.Section B6.1 - Transverse StiffenersThe limiting w/t ratio for the unstiffened elements of cold-formed steel transverse stiffeners was revised from 0.37to 0.42 .Section C2 - Tension MembersThe nominal tensile strength equation for axially loaded tension members was revised.  The limit states for determining thenominal tensile strength include (a) yielding in the gross section, (b) fracture in the net section away from connections, and (c)fracture in the effective net section at the connection.Section C3.1 - Strength for Bending OnlyA footnote was added to Section C3.1 to clearly state that the provisions of this Section do not consider torsional effects.Section C3.1.2.1 - Lateral-Torsional Buckling StrengthThe section number was changed from C3.1.2 to C3.1.2.1 with a title change to “Lateral-Torsional Buckling Strength.”  Thedesign equations for critical moments were changed to critical stress equations with some editorial revisions.Section C3.1.2.2 - Closed Box MembersThis is a new section for determining the lateral-torsional buckling strength of closed box members.  This section replacesSection D3.3 on Laterally Unbraced Box Beams.Section C3.1.3 - Beams Having One Flange Through-Fastened to Deck or SheathingThe R values used for determining the nominal flexural strength of simple span C- and Z- sections were replaced by tabulatedvalues (new Table 3.1-1) according to the depth and profile of the section.E Fys/.7 /E FystCCFSS Tech Bulletin August 1999"cos "θSection C3.1.4 - Beams Having One Flange Fastened to a Standing Seam Roof SystemThis Section was revised to permit the use of the reduction factor to be determined by the Base Test Method for purlins undergravity load or uplift load.Section C3.1.5 - Strength of Standing Seam Roof Panel SystemsThis is a new section specifying a methodology of interpreting the test results obtained by using ASTM E1592-95 procedure.Section C3.2.1 - Shear Strength of Webs without HolesThis is a new subsection containing the same design provisions included in Section C3.2 of the 1996 Edition of the Specification.Section C3.2.2 - Shear Strength of C-Section Webs with HolesThis is a new section dealing with the nominal shear strength of C-section beam webs with holes.  Design equations are givenfor computing the reduction factor on the basis of the web depth and the depth of web hole.Section C3.4.1 - Web Crippling Strength of  Webs without HolesThis subsection contains the same design provisions included in Section C3.4 of the 1996 Edition of the Specification.In Equations C3.4-1, C3.4-2, and C3.4-6, the constant C3 was replaced by C1.  The footnote was deleted.Section C3.4.2 - Web Crippling Strength of  C-Section Webs with HolesThis is a new section dealing with the nominal web crippling strength of C-section beam webs with holes.  Design equationsare given for computing reduction factors.Section C4 - Concentrically Loaded Compression MembersItem (c) of Section C4 for the limit of slenderness ratio, Kl/r, was moved from the Specification to the Commentary withadditional discussions.Section C6.1 - BendingThe D/t limits for Specification Equations C6.1-1 and C6.1-2 were revised slightly to provide better continuity.Section C6.2 - CompressionThe coefficient R was limited to be less than or equal to unity so that the effective area will not exceed the unreduced cross section area.Section D3.2.1 - Anchorage of Bracing for Roof Systems Under Gravity Load with Top Flange Connected to SheathingFor C-sections, a new equation was added to determine the restraint force PL for purlins with all compression flanges facingin the same direction.  For Z-sections, a term was added to the first term of all equations for computing the force PL.Section E2.6 - Resistance WeldsA design equation was added for determining the nominal shear strength of resistance welds.  This equation replaces thetabulated values given in previous specifications.Section E2.7 - Shear Lag Effect in Welded Connections of Members Other Than Flat SheetsThis is a new section for considering the shear lag effect in welded connections of  structural members.  Design equations aregiven for fracture and/or yielding in the effective net section of the connected parts.Section E3.2 - Shear Lag Effect in Bolted ConnectionsThe section title was revised to reflect the shear lag effect in bolted connections.  Design equations were added for determiningthe effective net area and for considering the effect of staggered holes.Section E3.3 - BearingNew equations were added for determining the nominal bearing strength of bolted connections when deformation around thebolt holes is a design consideration.In Tables E3.3-1 and E3.3-2, the lower thickness limit was revised from 0.024 in. (061 mm) to 0.036 in (0.91 mm).CCFSS Tech BulletinAugust 1999Section E5 - RuptureThe section title was revised to deal with shear rupture, tension rupture, and block shear rupture.   Design provisions andequations were added for tension rupture (new Section E5.2) and block shear rupture (new Section E5.3).Section E6.1 - BearingThis section was simplified by deleting all design equations for determining the nominal bearing strength in the contact areawith a concrete support.Section F1 - Tests for Determining Structural PerformanceStatistical data were added to Table F1 for structural members and connections not listed in the previous table.NASFA ANNOUNCES “THE RIGHT STUF”The North American Steel Framing Alliance (NASFA) recently announced the new universal designator system, “The RightSTUF,” that easily identifies any common cold-formed steel framing member and its implementation by several prominent steelstud manufacturing companies.“This new labeling system will directly address and help eliminate the problems associated with a lack of standards amongsteel stud producers,” said Don Moody, President of NASFA.Universal Designator System for Cold-Formed Steel Framing MembersThe Right STUF !!How the New Designator System WorksTo identify any common cold-formed steel framing member, the newdesignator system uses the web depth, flange width and minimum basemetal thickness of the framing member, in conjunction withthe following designators:S = Stud or Joist Sections with Flange Stiffeners (Cee Shapes)T = Track SectionsU = Cold Rolled Channel or Channel Studs (without flange stiffeners)F = Furring ChannelsThe flange width and web depth are expressed in 1/100th inches, and the minimum base metal thickness is expressed in mils(1 /1000th inches).ExamplesDesignation for a 6" - 16 gauge Cee with 1-5/8" flanges: 600S162-54Designation for a 3-1/2" - 20 gauge Track with 1-1/4" flanges: 350TI25-33The Logic Behind the New Designator SystemIt was decided to use the dimensions of the webs and flanges in the designators because they convey an intuitive picture ofthe shape in questions, kind of like a 2 X 4 describes a wood stud, for example. The web depth was put first, instead of the flangewidth (the 2 in 2 X 4) because for steel studs the strength-to-weight ratio is usually optimized by increasing depth instead of flangewidth, all else being equal.Minimum base metal thickness in mils (0.033 in.=33mils)1-1/4” flange in 1/100 inchesTrack section3-1/2” member depth in 1/100 inches (inside to inside dimension) 350 T 125 -331-5/8” flange in 1/100 inchesStud or joist with flange stiffeners6” member depth in 1/100 inches600 S 162 -54Minimum base metal thickness in mils (0.054 in.=54mils)CCFSS Tech Bulletin August 1999Center for Cold-Formed Steel Structures1870 Miner CircleUniversity of Missouri-RollaRolla, MO 65409-0030 USANon Profit Org.U.S. PostagePAIDPermit No. 170Rolla, MO 65401The web depth and flange width are expressed in 1 /100th inches because fractions are messy and there is such a variety ofdepths and widths available that rounding to the nearest fraction of an inch is not sufficiently descriptive. Also, one day the metricsystem may become universal, in which case the depths and widths would probably be expressed in millimeters, which in mostcases, would result in the same three digit format.The logic behind the alpha designators (S for Stud, T for Track, etc.) should be obvious.Minimum Base Metal ThicknessesThe minimum allowable base metal thickness designators were also agreed upon and are based on ICBO’s minimumprescribed thicknesses and expressed in mils. These minimum thicknesses have rapidly become the industry standards. Theminimum allowable bare steel thicknesses and their mill designators are as follows:25 gauge -0.0179" = 18 mil22 gauge -0.0269" = 27 mil20 gauge -0.0329" = 33 mil18 gauge -0.0428" = 43 milStiffening Lips on Cee SectionsThe dimension of the stiffening lip by flange width and material thickness was also agreed upon. The dimensions agreed uponare as follows:Material Thickness Flange Width, B Stiffening Lip, L0.0179"-0.0329" 1-1/4" 3/16"All thicknesses 1-3/8" 3/8"All thicknesses 1-5/8" 1/2"All thicknesses 2" 5/8"All thicknesses 2-1/2" 5/8"What’s Next?With the new standard designator system and the agreed upon minimum thicknesses and stiffening lip dimensions, the sectionproperties and load carrying abilities of any given profile can be calculated and standardized. Regardless of the manufacturer, notonly will the designation be identical for a standard framing member, but also the section properties and load carrying abilitiesof that standard member will be uniform throughout the country. In addition to helping eliminate the confusion in the marketstemming from the widely varying properties and loads published by manufacturers making essentially identical shapes, thesestandards should greatly facilitate submittals for plan check, code approvals, prescriptive standards, software development, etc.The intent is to make the products easier to use in existing markets and to accelerate their acceptance in new markets.For more information please visit the NASFA website: www.steelframingalliance.com16 gauge -0.0538" = 54 mil14 gauge -0.0677" = 68 mil12 gauge -0.0966" = 97 mil10 gauge -0.1180" = 118 milBL

CCFSS Technical Bulletin August 1999

https://scholarsmine.mst.edu/cgi/viewcontent.cgi?article=1001&context=ccfss-technical_bulletins

CCFSS Technical Bulletin August 1999

Abstract

Similar works

Full text

Available Versions

Missouri University of Science and Technology (Missouri S&T): Scholars' Mine