Efficient large-scale multiplexing of fiber Bragg grating and fiber Fabry-Perot sensors for structural health monitoring applications

Fiber Bragg gratings have been demonstrated as a versatile sensor for structural health monitoring. We present an efficient and cost effective multiplexing method for fiber Bragg grating and fiber Fabry-Perot sensors based on a broadband mode-locked fiber laser source and interferometric interrogation. The broadband, pulsed laser source permits time and wavelength division multiplexing to be employed to achieve very high sensor counts. Interferometric interrogation also permits high strain resolutions over large frequency ranges to be achieved. The proposed system has the capability to interrogate several hundred fiber Bragg gratings or fiber Fabry-Perot sensors on a single fiber, whilst achieving sub-microstrain resolution over bandwidths greater than 100 kHz. Strain resolutions of 30n epsilon/Hz(1/2) and 2 n epsilon/Hz(1/2) are demonstrated with the fiber Bragg grating and fiber Fabry-Perot sensor respectively. The fiber Fabry-Perot sensor provides an increase in the strain resolution over the fiber Bragg grating sensor of greater than a factor of 10. The fiber Bragg gratings are low reflectivity and could be fabricated during the fiber draw process providing a cost effective method for array fabrication. This system would find applications in several health monitoring applications where large sensor counts are necessary, in particular acoustic emission

Effects of long-term soluble vs. insoluble dietary fiber intake on high-fat diet-induced obesity in C57BL/6J mice

Although most of the proposed beneficial effects of fiber consumption have been attributed to viscous and gel-forming properties of soluble fiber, it is mainly insoluble cereal fiber and whole grains that are strongly associated with reduced diabetes risk in prospective cohort studies, indicating that other unknown mechanisms are likely to be involved. We performed a long-term study investigating potential protective effects of adding soluble guar fiber (10% w/w) vs. insoluble cereal fiber (10% w/w) to an isoenergetic and macronutrient matched high-fat diet in obesity-prone C57BL/6J mice. After 45 weeks, mice fed soluble vs. insoluble fiber showed both significantly increased body weight (41.8±3.0 vs. 33.6±1.5 g, P=.03) and elevated markers of insulin resistance. In mice fed soluble fiber, energy loss via the feces was significantly lower and colonic fermentation with production of short chain fatty acids (SCFA) was markedly increased. Gene expression analysis in white adipose tissue showed significantly increased levels of the fatty acid target G-protein coupled receptor-40 in soluble fiber-fed mice. Liver gene expression in the insoluble fiber group showed a pattern consistent with increased fatty acid oxidation. The present results show that soluble vs insoluble dietary fiber added to a high-fat, Western-style diet differently affected body weight and estimates of insulin sensitivity in obesity-prone mice. Soluble fiber intake with increased SCFA production significantly contributed to digested energy, thereby potentially outweighing the well known short-term beneficial effects of soluble fiber consumption

Comparison of the Mechanical Properties of Four-layer Epoxy Composite Reinforced with Natural Jute Fibers and Symmetrical E-glass Synthetic Fibers

Research that produces environmentally friendly products continues to be developing. Research related to the natural fiber jute material and epoxy matrix has done. Epoxy composite jute empowered do with the preparation of symmetry with four layers of fiber volume fraction of 27.89% and composite epoxy e-glass Fiber empowered four balance with 28.86% fiber volume fraction. Mechanical testing is done via Drag test to determine the tensile strength and stretch. From the analysis, it\u27s finding that the tensile strength of the symmetry jute fiber reinforced epoxy tensile strength was 48,378 MPa, and the strain was 11,998%. Meanwhile, the tensile strength and pressure in empowered epoxy e-glass fiber symmetry of four layers, each for 95.516 MPa and 7.7032%. Characterization has also been carried out through SEM testing. The results show that e-glass fiber fractures can still be seen as regular and tend to be straight and flat rods compared to symmetrical fiber-reinforced jute composite epoxy composites whose fibers are irregular. So that shows that the strength of the epoxy composite reinforced e-glass fiber is very large compared to the strength of the four-layer jute fiber-reinforced epoxy composite symmetry

High-resolution and broadband all-fiber spectrometers

The development of optical fibers has revolutionized telecommunications by enabling long-distance broad-band transmission with minimal loss. In turn, the ubiquity of high-quality low-cost fibers enabled a number of additional applications, including fiber sensors, fiber lasers, and imaging fiber bundles. Recently, we showed that a mutlimode optical fiber can also function as a spectrometer by measuring the wavelength-dependent speckle pattern formed by interference between the guided modes. Here, we reach a record resolution of 1 pm at wavelength 1500 nm using a 100 meter long multimode fiber, outperforming the state-of-the-art grating spectrometers. we also achieved broad-band operation with a 4 cm long fiber, covering 400 nm - 750 nm with 1 nm resolution. The fiber spectrometer, consisting of the fiber which can be coiled to a small volume and a monochrome camera that records the speckle pattern, is compact, lightweight, and low cost while providing ultrahigh resolution, broad bandwidth and low loss.Comment: 12 pages, 6 figure

Fiber distributed feedback laser

Utilizing round optical fibers as communication channels in optical communication networks presents the problem of obtaining a high efficiency coupling between the optical fiber and the laser. A laser is made an integral part of the optical fiber channel by either diffusing active material into the optical fiber or surrounding the optical fiber with the active material. Oscillation within the active medium to produce lasing action is established by grating the optical fiber so that distributed feedback occurs

Simulation of Optical Fiber Amplifier Gain Using Equivalent Short Fibers

Electromagnetic wave propagation in optical fiber amplifiers obeys Maxwell equations. Using coupled mode theory, the full Maxwell system within an optical fiber amplifier is reduced to a simpler model. The simpler model is made more efficient through a new scale model, referred to as an equivalent short fiber, which captures some of the essential characteristics of a longer fiber. The equivalent short fiber can be viewed as a fiber made using artificial (unphysical) material properties that in some sense compensates for its reduced length. The computations can be accelerated by a factor approximately equal to the ratio of the original length to the reduced length of the equivalent fiber. Computations using models of two commercially available fibers -- one doped with ytterbium, and the other with thulium -- show the practical utility of the concept. Extensive numerical studies are conducted to assess when the equivalent short fiber model is useful and when it is not

Direct fiber vector eigenmode multiplexing transmission seeded by integrated optical vortex emitters

Spatial modes have received substantial attention over the last decades and are used in optical communication applications. In fiber-optic communications, the employed linearly polarized modes and phase vortex modes carrying orbital angular momentum can be synthesized by fiber vector eigenmodes. To improve the transmission capacity and miniaturize the communication system, straightforward fiber vector eigenmode multiplexing and generation of fiber-eigenmode-like polarization vortices (vector vortex modes) using photonic integrated devices are of substantial interest. Here, we propose and demonstrate direct fiber vector eigenmode multiplexing transmission seeded by integrated optical vortex emitters. By exploiting vector vortex modes (radially and azimuthally polarized beams) generated from silicon microring resonators etched with angular gratings, we report data-carrying fiber vector eigenmode multiplexing transmission through a 2-km large-core fiber, showing low-level mode crosstalk and favorable link performance. These demonstrations may open up added capacity scaling opportunities by directly accessing multiple vector eigenmodes in the fiber and provide compact solutions to replace bulky diffractive optical elements for generating various optical vector beams