Compound cycle engine for helicopter application

The Compound Cycle Engine (CCE) is a highly turbocharged, power compounded, ultra-high power density, light-weight diesel engine. The turbomachinery is similar to a moderate pressure ratio, free power turbine engine and the diesel core is high speed and a low compression ratio. This engine is considered a potential candidate for future military light helicopter applications. This executive summary presents cycle thermodynamic (SFC) and engine weight analyses performed to establish general engine operating parameters and configuration. An extensive performance and weight analysis based on a typical two hour helicopter (+30 minute reserve) mission determined final conceptual engine design. With this mission, CCE performance was compared to that of a T-800 class gas turbine engine. The CCE had a 31% lower-fuel consumption and resulted in a 16% reduction in engine plus fuel and fuel tank weight. Design SFC of the CCE is 0.33 lb-HP-HR and installed wet weight is 0.43 lbs/HP. The major technology development areas required for the CCE are identified and briefly discussed

VSCE technology definition study

Refined design definition of the variable stream control engine (VSCE) concept for advanced supersonic transports is presented. Operating and performance features of the VSCE are discussed, including the engine components, thrust specific fuel consumption, weight, noise, and emission system. A preliminary engine design is presented

Advanced rotary engine studies

A review of rotary engine developments relevant to a stratified charge rotary aircraft engine is presented. Advantages in module size and weight, fuel efficiency, reliability, and multi-fuel capability are discussed along with developments in turbocharging, increased mean effective pressure, improved apex seal/trochoid wear surfacing materials, and high strength and temperature aluminum casting alloys. A carbureted prototype aircraft engine is also described

Preliminary Evaluation of a Turbine/Rotary Combustion Compound Engine for a Subsonic Transport

The fuel consumption of a modern compound engine with that of an advanced high pressure ratio turbofan was compared. The compound engine was derived from a turbofan engine by replacing the combustor with a rotary combustion (RC) engine. A number of boost pressure ratios and compression ratios were examined. Cooling of the RC engine was accomplished by heat exchanging to the fan duct. Performance was estimated with an Otto-cycle for two levels of energy lost to cooling. The effects of added complexity on cost and maintainability were not examined and the comparison was solely in terms of cruise performance and weight. Assuming a 25 percent Otto-cycle cooling loss (representative of current experience), the best compound engine gave a 1.2 percent improvement in cruise. Engine weight increased by 23 percent. For a 10 percent Otto-cycle cooling loss (representing advanced insulation/high temperature materials technology), a compound engine with a boost PR of 10 and a compression ratio of 10 gave an 8.1 percent lower cruise than the reference turbofan

The stirling engine for vehicle propulsion

The performance data of experimental Stirling engines are considered along with questions of exhaust-gas composition, engine noise, engine volume and weight, engine control, and the engine-starting process. The Stirling engine can use practically any liquid or gaseous fuel for its operation. It is found that technically a use of the Stirling engine in motor vehicles is feasible. Economic questions related to an introduction of the Stirling engine are discussed along with possible new developments which could improve the economic situation in favor of a use of Stirling engine

Study of small turbofan engines applicable to general-aviation aircraft

The applicability of small turbofan engines to general aviation aircraft is discussed. The engine and engine/airplane performance, weight, size, and cost interrelationships are examined. The effects of specific engine noise constraints are evaluated. The factors inhibiting the use of turbofan engines in general aviation aircraft are identified

A quantum Szilard engine without heat from a thermal reservoir

We study a quantum Szilard engine that is not powered by heat drawn from a thermal reservoir, but rather by projective measurements. The engine is constituted of a system $\mathcal{S}$, a weight $\mathcal{W}$, and a Maxwell demon $\mathcal{D}$, and extracts work via measurement-assisted feedback control. By imposing natural constraints on the measurement and feedback processes, such as energy conservation and leaving the memory of the demon intact, we show that while the engine can function without heat from a thermal reservoir, it must give up at least one of the following features that are satisfied by a standard Szilard engine: (i) repeatability of measurements; (ii) invariant weight entropy; or (iii) positive work extraction for all measurement outcomes. This result is shown to be a consequence of the Wigner-Araki-Yanase (WAY) theorem, which imposes restrictions on the observables that can be measured under additive conservation laws. This observation is a first-step towards developing "second-law-like" relations for measurement-assisted feedback control beyond thermality

Quiet engine program flight engine design study

The results are presented of a preliminary flight engine design study based on the Quiet Engine Program high-bypass, low-noise turbofan engines. Engine configurations, weight, noise characteristics, and performance over a range of flight conditions typical of a subsonic transport aircraft were considered. High and low tip speed engines in various acoustically treated nacelle configurations were included

Airflow distribution control for improved turbine engine performance

Control allows significant diffuser length and weight reduction, reduces combustor exhaust emissions during engine idle, and improves combustor altitude relight capability

Orbit Transfer Vehicle (OTV) engine study, phase "A" extension 2

The operation of the Advanced Expander Cycle OTV engine was evaluated at high mixture ratios, and intermediate and low thrust levels to establish the impact upon the engine design and costs, and/or operating characteristics. The engine operation was analyzed at tank head and pumped idle conditions with the nozzle extension retracted. The engine performance, weight, and envelope parametrics data were expanded to include mixture ratios of 7.5 and 8.0