Directivity and spacing for the antenna elements

The optimum design choice for the MST radar antenna was considered. The following factors are required: directivity and gain; beam width and its symmetry; sidelobe levels, near and wide angle; impedance matching; feeder network losses; polarization diversity; steerability; cost effectiveness; and maintainability. The directivity and related beam forming aspects of various antenna elements and directivity aspects when such elements are formed into an array are discussed. Array performance for important variables, in particular, the spacing of the elements is considered

Dielectric nanoantenna as an efficient and ultracompact demultiplexer for surface waves

Nanoantennas for highly efficient excitation and manipulation of surface waves at nanoscale are key elements of compact photonic circuits. However, previously implemented designs employ plasmonic nanoantennas with high Ohmic losses, relatively low spectral resolution, and complicated lithographically made architectures. Here we propose an ultracompact and simple dielectric nanoantenna (silicon nanosphere) allowing for both directional launching of surface plasmon polaritons on a thin gold film and their demultiplexing with a high spectral resolution. We show experimentally that mutual interference of magnetic and electric dipole moments supported by the dielectric nanoantenna results in opposite propagation of the excited surface waves whose wavelengths differ by less than 50 nm in the optical range. Broadband reconfigurability of the nanoantennas operational range is achieved simply by varying the diameter of the silicon sphere. Moreover, despite subwavelength size ($<\lambda/3$) of the proposed nanoantennas, they demonstrate highly efficient and directional launching of surface waves both in the forward and backward directions with the measured front-to-back ratio having a contrast of almost two orders of magnitude within a 50 nm spectral band. Our lithography-free design has great potential as highly efficient, low-cost, and ultracompact demultiplexer for advanced photonic circuits.Comment: added relevant references; fixed typos in Supplementary eq. 8,9,1

Performance of hemielliptic dielectric lens antennas with optimal edge illumination

The role of edge illumination in the performance of compact-size dielectric lens antennas (DLAs) is studied in accurate manner using a highly efficient algorithm based on the combination of the Muller boundary integral equations and the method of analytical regularization. The analysis accounts for the finite size of the lens and directive nature of the primary feed placed close to the center of the lens base. The problem is solved in a two-dimensional formulation for both E- and H-polarizations. It is found that away from internal resonances that spoil the radiation characteristics of DLAs made of dense materials, the edge illumination has primary importance. The proper choice of this parameter helps maximize DLA directivity, and its optimal value depends on the lens material and feed polarization. Index Terms: Beam collimation, dielectric lens antenna, directivity improvement, edge illumination, edge taper, hemielliptic lens.Comment: 5 pages, 9 figure

Optimizing an array of antennas for cellular coverage from a high altitude platform

In a wireless communications network served by a high altitude platform (HAP) the cochannel interference is a function of the antenna beamwidth, angular separation and. sidelobe level. At the millimeter wave frequencies proposed for HAPs, an array of aperture type antennas on the platform is a practicable solution for serving the cells. We present a method for predicting cochannel interference based on curve-fit approximations for radiation patterns of elliptic beams which illuminate cell edges with optimum power, and a means of estimating optimum beamwidths for each cell of a regular hexagonal layout. The method is then applied to a 121 cell architecture. Where sidelobes are modeled As a flat floor at 40-dB below peak directivity, a cell cluster size of four yields carrier-to-interference ratios (CIRs), which vary from 15 dB at cell edges to 27 dB at cell centers. On adopting a cluster size of seven, these figures increase, respectively, to 19 and 30 dB. On reducing the sidelobe level, the. improvement in CIR can be quantified. The method also readily allows for regions of overlapping channel coverage to be shown

Directivity patterns of laser-generated sound in solids: Effects of optical and thermal parameters

In the present paper, directivity patterns of laser-generated sound in solids are investigated theoretically. Two main approaches to the calculation of directivity patterns of laser-generated sound are discussed for the most important case of thermo-optical regime of generation. The first approach, which is widely used in practice, is based on the simple modelling of the equivalent thermo-optical source as a mechanical dipole comprising two horizontal forces applied to the surface in opposite directions. The second approach is based on the rigorous theory that takes into account all acoustical, optical and thermal parameters of a solid material and all geometrical and physical parameters of a laser beam. Directivity patterns of laser-generated bulk longitudinal and shear elastic waves, as well as the amplitudes of generated Rayleigh surface waves, are calculated for different values of physical and geometrical parameters and compared with the directivity patterns calculated in case of dipole-source representation. It is demonstrated that the simple approach using a dipole-source representation of laser-generated sound is rather limited, especially for description of generated longitudinal acoustic waves. A practical criterion is established to define the conditions under which the dipole-source representation gives predictions with acceptable errors. It is shown that, for radiation in the normal direction to the surface, the amplitudes of longitudinal waves are especially sensitive to the values of thermal parameters and of the acoustic reflection coefficient from a free solid surface. A discussion is given on the possibility of using such a high sensitivity to the values of the reflection coefficient for investigation of surface properties of real solids.Comment: 14 pages, 7 figure

Microphotonic parabolic light directors fabricated by two-photon lithography

We have fabricated microphotonic parabolic light directors using two-photon lithography, thin-film processing, and aperture formation by focused ion beam lithography. Optical transmission measurements through upright parabolic directors 22 μm high and 10 μm in diameter exhibit strong beam directivity with a beam divergence of 5.6°, in reasonable agreement with ray-tracing and full-field electromagnetic simulations. The results indicate the suitability of microphotonic parabolic light directors for producing collimated beams for applications in advanced solar cell and light-emitting diode designs