Self-Collimation in Planar Photonic Crystals

We analyze, in three dimensions, the dispersion properties of dielectric slabs perforated with two-dimensional photonic crystals (PCs) of square symmetry. The band diagrams are calculated for all -vectors in the first Brillouin zone, and not only along the characteristic high-symmetry directions. We have analyzed the equal-frequency contours of the first two bands, and we found that the square lattice planar photonic crystal is a good candidate for the self-collimation of light beams. We map out the group velocities for the second band of a square lattice planar PC and show that the group velocity is the highest in the region of maximum self-collimation. Such a self-collimated beam is predicted to show beating patterns due to the specific shape of the equal-frequency contours. A geometrical transformation maps the region of the first and second photonic bands where self-collimation takes place one onto the other and gives additional insights on the structural similarities of self-collimation in those two bands

Surface plasmon enhanced light-emitting diode

A method for enhancing the emission properties of light-emitting diodes, by coupling to surface plasmons, is analyzed both theoretically and experimentally. The analyzed structure consists of a semiconductor emitter layer thinner than λ/2 sandwiched between two metal films. If a periodic pattern is defined in the top semitransparent metal layer by lithography, it is possible to efficiently couple out the light emitted from the semiconductor and to simultaneously enhance the spontaneous emission rate. For the analyzed designs, we theoretically estimate extraction efficiencies as high as 37% and Purcell factors of up to 4.5. We have experimentally measured photoluminescence intensities of up to 46 times higher in fabricated structures compared to unprocessed wafers. The increased light emission is due to an increase in the efficiency and an increase in the pumping intensity resulting from trapping of pump photons within the microcavity

Methods for controlling positions of guided modes of photonic-crystal waveguides

We analyze different methods for controlling positions of guided modes of planar photonic-crystal waveguides. Methods based both on rearrangements of holes in the photonic-crystal lattice and on changes of hole sizes are presented. The ability to tune frequencies of guided modes within a frequency bandgap is necessary to achieve efficient guiding of light within a waveguide, as well as to match frequencies of eigenmodes of different photonic-crystal-based devices for the purpose of good coupling between them. We observe and explain the appearance of acceptor-type modes in donor-type waveguides

Photonic crystal laser sources for chemical detection

We have realized photonic crystal lasers that permit the introduction of analyte within the peak of the optical field of the lasing mode. We have explored the design compromises for developing such sensitive low-threshold spectroscopy sources, and demonstrate the operation of photonic crystal lasers in different ambient organic solutions. We show that nanocavity lasers can be used to perform spectroscopic tests on femtoliter volumes of analyte, and propose to use these lasers for high-resolution spectroscopy with single-molecule sensitivity

High quality factors and room-temperature lasing in a modified single-defect photonic crystal cavity

We propose and analyze a new photonic crystal cavity design that supports a dipole mode with a quality factor greater than 20,000. Such a high quality factor is obtained by precise tuning of the cavity length with minimal disruption of the surrounding photonic crystal. A fabrication procedure based on dry etching of InGaAsP material in HI/H2/Ar is used to demonstrate photonic crystal lasers with smooth and straight sidewalls. These room-temperature lasers concentrate optical energy in air and are suitable for use as tunable lasers and chemical sensors

Design and Fabrication of Silicon Photonic Crystal Optical Waveguides

We have designed and fabricated waveguides that incorporate two-dimensional (2-D) photonic crystal geometry for lateral confinement of light, and total internal reflection for vertical confinement. Both square and triangular photonic crystal lattices were analyzed. A three-dimensional (3-D) finite-difference time-domain (FDTD) analysis was used to find design parameters of the photonic crystal and to calculate dispersion relations for the guided modes in the waveguide structure. We have developed a new fabrication technique to define these waveguides into silicon-on-insulator material. The waveguides are suspended in air in order to improve confinement in the vertical direction and symmetry properties of the structure. High-resolution fabrication allowed us to include different types of bends and optical cavities within the waveguides

Quantum photonic networks in diamond

Advances in nanotechnology have enabled the opportunity to fabricate nanoscale optical devices and chip-scale systems in diamond that can generate, manipulate, and store optical signals at the single-photon level. In particular, nanophotonics has emerged as a powerful interface between optical elements such as optical fibers and lenses, and solid-state quantum objects such as luminescent color centers in diamond that can be used effectively to manipulate quantum information. While quantum science and technology has been the main driving force behind recent interest in diamond nanophotonics, such a platform would have many applications that go well beyond the quantum realm. For example, diamond’s transparency over a wide wavelength range, large third-order nonlinearity, and excellent thermal properties are of great interest for the implementation of frequency combs and integrated Raman lasers. Diamond is also an inert material that makes it well suited for biological applications and for devices that must operate in harsh environments

Photonic crystals for confining, guiding, and emitting light

We show that by using the photonic crystals, we can confine, guide, and emit light efficiently. By precise control over the geometry and three-dimensional design, it is possible to obtain high quality optical devices with extremely small dimensions. Here we describe examples of high-Q optical nanocavities, photonic crystal waveguides, and surface plasmon enhanced light-emitting diode (LEDs)