4 research outputs found
Wear-adaptive optimization of in-process conditioning parameters during face plunge grinding of PcBN
Polycrystalline cubic boron nitride is a very hard material. Machining of this material is performed by grinding with diamond tools. Due to its high hardness, grinding tools are subjected to severe microscopic and macroscopic tool wear. This wear leads to short tool life and results in high effort in conditioning the abrasive layer. Contrary to the usual conditioning of diamond grinding wheels with diamond dressing tools, this study investigates a conditioning process based entirely on the use of white corundum cup rolls. These conditioning tools allow the in-process face plunge conditioning of vitrified bond diamond grinding tools. The circumferential speed of the conditioning tool and the average grain diameter of the corundum are identified as the main factors influencing the topography of the generated grinding layer. To describe the performance of the conditioning process, a specific conditioning removal rate Q′sd is derived. This parameter represents a cumulated variable that allows a comparison of different conditioning strategies. It is shown that an increase in Q′sd significantly counteracts microscopic wear on the abrasive layer. Therefore, optimized process parameters enable the process of in-process conditioning to significantly reduce wear on the grinding tool without increasing the process time or the non-productive time
Influence of dressing strategy on tool wear and performance behavior in grinding of forming tools with toric grinding pins
The performance of grinding tools in grinding processes and the resulting surface and subsurface properties depend on various factors. The condition of the grinding tool after dressing is one of these factors. However, the influence of the dressing process on the condition of the grinding tool depends on the selected process parameters and is difficult to predict. Therefore, this paper presents an approach to describe the influence of the dressing process on tool wear of toric grinding pins and the resulting subsurface modification. For this purpose, toric grinding pins with a vitrified bond were dressed with two different strategies and the wear and operational behavior were investigated when grinding AISI M3:2 tool steel with two different grinding strategies. In general, the investigations have shown that the dressing process influences the performance and wear behavior differently depending on the grinding strategy used. The degree of clogging is influenced by the geometric contact sizes. In the case of small engagement cross sections with simultaneously large contact lengths the thermal tool load is distributed over a small annular area of the tool and favors clogging. Crushing and additional transverse loading of the grains result in an almost clog-free tool surface. This also leads to a lower G-ratio. Crushing leads to an intensified decrease of the torus radii. The influence of the dressing strategy can also be observed in the induced residual stresses. Toric grinding pins dressed by crushing induce lower compressive residual stresses into the workpiece, which can be attributed to the self-sharpening effect. This effect reduces the mechanical and thermomechanical load of the workpiece during machining
Process-related characteristic–based topography evaluation of wear conditions on grinding wheels
Non-productive auxiliary processes affect the single part and small badge production of milling tools. The key production process grinding is inevitably linked to the auxiliary conditioning process. The time demand of those process steps decreases the overall productivity of the manufacturing process. However, today the machine operator decides on conditioning cycles individually by the use of experience. Until today, there is no objective data based approach available that supports the initiation of these conditioning processes or the adaption of the grinding process itself in order to improve its process efficiency. For this purpose, a process-related topography evaluation method of the grinding wheel surface is developed within this study. For the measurement, an optical method based on laser triangulation is used. The measurement system is implemented into a common tool grinding machine tool. In addition, characteristic topography values are defined that show the wear conditions of the grinding tool. Moreover, the data is summarized in a database of wear conditions. The developed measurement method can save grinding and dressing tool resources, process times and minimizes scrap parts. In addition, an adaptation of the process and a targeted launch of auxiliary processes can be enabled. The novel characteristic-based topography measurement creates the opportunity to enhance the tool life of the grinding wheels up to 30% without losing productivity
Influence of end mill manufacturing on cutting edge quality and wear behaviorInfluence of End Mill Manufacturing on Cutting Edge Quality and Wear Behavior
One of the decisive factors for the performance of milling tools is the quality of the cutting edge. The latter results from the process control of the individual steps along the tool manufacturing process chain, which generally includes the sintering or pressing of the blanks, grinding, cutting edge preparation, and coating of the tools. However, the targeted and application-specific design of the process steps in terms of high economic efficiency is currently limited by a lack of knowledge regarding the influence of the corresponding process parameters on the resulting cutting edge quality. In addition, there is a lack of suitable parameters that adequately represent the characteristics of the cutting edge microtopography. This publication therefore investigates the influence of manufacturing processes on cutting edge quality and wear behavior of end mills. On this basis, different characterization parameters for the cutting edge quality are derived and evaluated with regard to their ability to predict the wear behavior