On the Halo Occupation of Dark Baryons

We introduce a new technique that adopts the halo occupation framework for understanding the origin of QSO absorption-line systems. Our initial study focuses specifically on MgII absorbers. We construct a model of the gaseous content in which the absorption equivalent width W_r is determined by the the amount of cold gas, in the form of discrete clouds, along a sightline through a halo. The two quantities that we specify per halo in the model are (1) the mean absorption strength per unit surface mass density A_W(M), and (2) the mean covering factor kappa_g(M) of the gaseous clouds. These parameters determine the conditional probability distribution of W_r as a function of halo mass, P(W_r|M). Two empirical measurements are applied to constrain the model: (i) the absorber frequency distribution function and (ii) the W_r-dependent clustering amplitude. We find that the data demand a rapid transition in the gas content of halos at ~10^11.5 Msol/h, below which halos contain predominantly cold gas and beyond which gas becomes predominantly hot. In order to reproduce the observed overall strong clustering of the absorbers and the anti-correlation between W_r and halo mass M, roughly 5% of gas in halos up to 10^14 Msol/h is required to be cold. The gas covering factor is near unity over a wide range of halo mass, supporting that Mg II systems probe an unbiased sample of typical galaxies. We discuss the implications of our study in the contexts of mass assembly of distant galaxies and the origin of QSO absorption line systems.Comment: 15 emulateapj pages, 7 figures, replaced with revised version incorporating referee's comment

Global well-posedness for the Gross-Pitaevskii equation with an angular momentum rotational term in three dimensions

In this paper, we establish the global well-posedness of the Cauchy problem for the Gross-Pitaevskii equation with an angular momentum rotational term in which the angular velocity is equal to the isotropic trapping frequency in the space \Real^3.Comment: 11 page

Quantitation of buried contamination by use of solvents

Experiments directed at determining the potential of reclaimed silicone polymers for reuse are described

The Last Eight-Billion Years of Intergalactic SiIV Evolution

We identified 24 SiIV absorption systems with z <~ 1 from a blind survey of 49 low-redshift quasars with archival Hubble Space Telescope ultraviolet spectra. We relied solely on the characteristic wavelength separation of the doublet to automatically detect candidates. After visual inspection, we defined a sample of 20 definite (group G = 1) and 4 "highly-likely" (G = 2) doublets with rest equivalent widths W_r for both lines detected at > 3 sigma. The absorber line density of the G = 1 doublets was dN_SiIV/dX = 1.4+0.4/-0.3 for log N(Si+3) > 12.9. The best-fit power law to the G = 1 frequency distribution of column densities f(N(Si+3)) had normalization k = (1.2+0.5/-0.4) x 10^-14 cm2 and slope alpha = -1.6+0.3/-0.3. Using the power-law model of f(N(Si+3)), we measured the Si+3 mass density relative to the critical density: Omega(Si+3) = (3.7+2.8/-1.7) x 10^-8 for 13 < log N(Si+3) < 15. From Monte Carlo sampling of the distributions, we estimated our value to be a factor of 4.8+3.0/-1.9 higher than the 2 . From a simple linear fit to Omega(Si+3) over the age of the Universe, we estimated a slow and steady increase from z = 5.5 --> 0 with dOmega/dt_age = (0.61+/-0.23) x 10^-8 Gyr^-1. We compared our ionic ratios N(Si+3)/N(C+3) to a 2 < z < 4.5 sample and concluded, from survival analysis, that the two populations are similar, with median = 0.16.Comment: 18 pages, 9 figures, 4 tables, added figures and new analysis, results have changed, accepted to Ap

Quantitation of buried contamination by use of solvents

Spore recovery form cured silicone potting compounds using amine solvents to degrade the cured polymers was investigated. A complete list of solvents and a description of the effect of each on two different silicone polymers is provided

Generation of helical gears with new surfaces, topology by application of CNC machines

Analysis of helical involute gears by tooth contact analysis shows that such gears are very sensitive to angular misalignment that leads to edge contact and the potential for high vibration. A new topology of tooth surfaces of helical gears that enables a favorable bearing contact and a reduced level of vibration is described. Methods for grinding of the helical gears with the new topology are proposed. A TCA (tooth contact analysis) program for simulation of meshing and contact of helical gears with the new topology has been developed. Numerical examples that illustrate the proposed ideas are discussed