413 research outputs found
Active noise compensation for multichannel magnetocardiography in an unshielded environment
A multichannel high-T/sub c/-SQUID-based heart scanner for unshielded environments is under development, Outside a magnetically shielded room, sensitive SQUID measurements are possible using gradiometers. However, it is difficult to realize large-baseline gradiometers in high-T/sub c/ materials, Therefore, the authors developed two active noise compensation techniques. In the Total Field Compensation technique, a Helmholtz type coil set is placed around the sensors. One magnetometer is used as a zero detector controlling the compensation current through the coil set. For Individual Flux Compensation, the reference signal is sent to the separate SQUIDs (or their flux transformer circuits) to compensate the local environmental noise fluxes, The latter technique was tested on low-T/sub c/ rf-SQUID magnetometers, each sensor set to a field resolution SQUID magnetometers, i.e. 0.1 pT/sub RMS///spl radic/Hz. The authors were able to suppress the environmental disturbances to such an extent that magnetocardiograms could be recorded in an ordinary environment. Here the two suppression techniques are described and experimental results are presente
A new microscopic nucleon-nucleon interaction derived from relativistic mean field theory
A new microscopic nucleon-nucleon (NN) interaction has been derived for the
first time from the popular relativistic mean field theory (RMFT) Lagrangian.
The NN interaction so obtained remarkably relate to the inbuilt fundamental
parameters of RMFT. Furthermore, by folding it with the RMFT-densities of
cluster and daughter nuclei to obtain the optical potential, it's application
is also examined to study the exotic cluster radioactive decays, and results
obtained found comparable with the successfully used M3Y phenomenological
effective NN interactions. The presently derived NN-interaction can also be
used to calculate a number of other nuclear observables.Comment: 4 Pages 2 Figure
Sensitivity of Micromachined Joule-Thomson Cooler to Clogging Due to Moisture
A major issue in long-term operation of micromachined Joule-Thomson coolers is the clogging of the microchannels and/or the restriction due to the deposition of water molecules present in the working fluid. In this study, we present the performance of a microcooler operated with nitrogen gas with different moisture levels. Relatively low-purity nitrogen gas (5.0) is supplied from a gas bottle and led through a filter to control the moisture level. The filter consists of a tube-in-tube counter flow heat exchanger (CFHX) and a heat exchanger that is stabilized at a certain temperature by using a Stirling cooler. The set-point temperature determines the moisture level at the exit of the heat exchanger. It is found that the moisture level has influence on the mass-flow rate during the cool down. Once the microcooler reaches the set cold-end temperature, the main deposition area shifts into the CFHX and the moisture level at the restriction is almost independent on the inlet moisture level of the microcooler. The moisture level at the restriction increases with the increasing cold-end temperature when the cold-end temperature is lower than the saturation temperature of the water in the nitrogen gas. Higher cold-end temperature results in higher clogging rate
Vibration-free Cooler for the METIS Instrument Using Sorption Compressors
METIS is the âMid-infrared ELT Imager and Spectrographâ for the European Extremely Large Telescope (E-ELT) that will cover the thermal/mid-infrared wavelength range from 3-14 micron. Starting from a pumped nitrogen line at 70K, it requires cryogenic cooling of detectors and optics at 40 K (1.4 W), 25 K (1.1 W), and 8 K (0.4 W). A vibration-free cooling technology for this instrument based on sorption coolers is under development at the University of Twente in collaboration with Dutch Space. We propose a sorption-based cooler with three cascaded Joule-Thomson coolers of which the sorption compressors are all heat sunk at the 70K platform. A helium-operated cooler is used to obtain the 8K level with a cooling power of 0.4 W. Here, three pre-cooling stages are used at 40K, 25K and 15K. The latter two levels are provided by a hydrogen-based cooler, whereas the 40K level is realized by a neon-based sorption cooler. Based on our space-cooler heritage, our preliminary design used sorption compressors equipped with gas-gap heat switches. These have maximum efficiency, but the gas-gap switches add significantly to the complexity of the system. Since in METIS relatively high cooling powers are required, and thus a high number of compressor cells, manufacturability is an important issue. We, therefore, developed an alternative cylindrical compressor design that uses short-pulse heating establishing a thermal wave in radial direction. This allows to omit the gas-gap heat switch. The paper discusses the adapted cell design and two METIS cooler demonstrator setups that are currently under construction
A Passive, Adaptive and Autonomous Gas Gap Heat Switch
We report on the development of a heat switch for autonomous temperature control of electronic components in a satellite. A heat switch can modulate when needed between roles of a good thermal conductor and a good thermal insulator. Electronic boxes on a satellite should be maintained within a typical optimum temperature range of 260 to 310 K. The heat sinking is usually by means of a radiator. When the operating temperature of the electronic box increases beyond 310 K, a good contact to the radiator is desired for maximum cooling. On the other hand, when the satellite is in a cold dormant state, the electronics box should be heated by the onboard batteries. In this state a weak thermal contact is desired between the electronic box and the heat sink. In the present study, we are developing a gas gap heat switch in which the sorber material is thermally anchored to the electronic box. A temperature change of the electronic box triggers the (de-)sorption of gas from the sorber material and subsequently the gas pressure in the gas gap. This paper describes the physical principles and the current status of this technology. This approach can be extended to cryogenic temperature rang
- âŠ