Entanglement, BEC, and superfluid-like behavior of two-mode photon systems

A system of two interacting photon modes, without constraints on the photon number, in the presence of a Kerr nonlinearity, exhibits BEC if the transfer amplitude is greater than the mode frequency. A symmetry-breaking field (SBF) can be introduced by taking into account a classical electron current. The ground state, in the limit of small nonlinearity, becomes a squeezed state, and thus the modes become entangled. The smaller is the SBF, the greater is entanglement. Superfluid-like behavior is observed in the study of entanglement growth from an initial coherent state, since in the short-time range the growth does not depend on the SBF amplitude, and on the initial state amplitude. On the other hand, the latter is the only parameter which determines entanglement in the absence of the SBF

Teleportation on a quantum dot array

We present a model of quantum teleportation protocol based on a double quantum dot array. The unknown qubit is encoded using a pair of quantum dots, coupled by tunneling, with one excess electron. It is shown how to create maximally entangled states with this kind of qubits using an adiabatically increasing Coulomb repulsion between different pairs. This entangled states are exploited to perform teleportation again using an adiabatic coupling between them and the incoming unknown state. Finally, a sudden separation of Bob's qubit enables a time evolution of Alice's state providing a modified version of standard Bell measurement. Substituting the four quantum dots entangled state with a chain of coupled DQD's, a quantum channel with high fidelity arises from this scheme allowing the transmission over long distances.Comment: 4 pages, 2 figure

Identification of Test Structures for Reduced Order Modeling of the Squeeze Film Damping in Mems

In this study the dynamic behaviour of perforated microplates oscillating under the effect of squeeze film damping is analyzed. A numerical approach is adopted to predict the effects of damping and stiffness transferred from the surrounding ambient air to oscillating structures ; the effect of hole's cross section and plate's extension is observed. Results obtained by F.E.M. models are compared with experimental measurements performed by an optical interferometric microscope.Comment: Submitted on behalf of EDA Publishing Association (http://irevues.inist.fr/EDA-Publishing

Invariant measures on multimode quantum Gaussian states

We derive the invariant measure on the manifold of multimode quantum Gaussian states, induced by the Haar measure on the group of Gaussian unitary transformations. To this end, by introducing a bipartition of the system in two disjoint subsystems, we use a parameterization highlighting the role of nonlocal degrees of freedom -- the symplectic eigenvalues -- which characterize quantum entanglement across the given bipartition. A finite measure is then obtained by imposing a physically motivated energy constraint. By averaging over the local degrees of freedom we finally derive the invariant distribution of the symplectic eigenvalues in some cases of particular interest for applications in quantum optics and quantum information.Comment: 17 pages, comments are welcome. v2: presentation improved and typos corrected. Close to the published versio

Mesoscopic continuous and discrete channels for quantum information transfer

We study the possibility of realizing perfect quantum state transfer in mesoscopic devices. We discuss the case of the Fano-Anderson model extended to two impurities. For a channel with an infinite number of degrees of freedom, we obtain coherent behavior in the case of strong coupling or in weak coupling off-resonance. For a finite number of degrees of freedom, coherent behavior is associated to weak coupling and resonance conditions

Influence of biochar on the physical, chemical and retention properties of an amended sandy soil

Soil porosity plays an important role in soil-water retention and water availability to crops, potentially affecting both agricultural practices and environmental sustainability. The pore structure controls fluid flow and transport through the soil, as well as the relationship between the properties of individual minerals and plants. Moreover, the anthropogenic pressure on soil properties has produced numerous sites with extensive desertification process close to residential areas. Biochar (biologically derived charcoal) is produced by pyrolysis of biomasses under low oxygen conditions, and it can be applied for recycling organic waste in soils and increase soil fertility, improving soil structure and enhancing soil water storage and soil water movement. Soil application of biochar might have agricultural, environmental and sustainability advantages over the use of organic manures or compost, as it is a porous material with a high inner surface area. The main objectives of the present study were to investigate the possible application of biochar from forest residues, derived from mechanically chipped trunks and large branches of Abies alba M., Larix decidua Mill., Picea excelsa L., Pinus nigra A. and Pinus sylvestris L. pyrolysed at 450 C for 48h, to improve soil structural and hydraulic properties (achieving a stabilization of soil). Different amount of biochar were added to a desertic sandy soil, and the effect on soil porosity water retention and water available to crops were investigated. The High Energy Moisture Characteristic (HEMC) technique was applied to investigate soil-water retention at high-pressure head levels. The adsorption and desorption isotherms of N2 on external surfaces were also determined in order to investigate micro and macro porosity ratio. Both the described model of studies on adsorption-desorption experiments with the applied isotherms model explain the increasing substrate porosity with a particular attention to the macro and micro porosity, respectively

Comparison between piezoelectric and magnetic strategies for wearable energy harvesting

This paper introduces the design and fabrication of energy harvesters for the power generation from human body motion. Two alternative strategies are compared: piezoelectric and magnetic inductive. The generated energy is used to supply body sensors including accelerometers and temperature sensors and RF module. Two prototypes of the magnetic based generator and of the piezoelectric generator are built and tested with shaker at resonance condition and by dedicated bench reproducing joints rotation during walking. The experimental results show that the magnetic prototype can generate 0.7mW from human body motion, while the piezo harvester generates 0.22 and 0.33μW respectively for flexion and extension at angular velocity lower than 1rad/s and 45° amplitude

Modeling of lattice structures energy absorption under impact loads

Lattice structures are promising design solutions for lightweight components in many industrial fields as aeronautics and space. The multifunctional design approach aims to combine in the same component several capabilities, including the ability to absorb impact energy with high efficiency. The additive manufacturing of metals is presently opening to innovative constructive approaches where static strength, lightweight and impact behavior must be considered together in design and simulation. This paper introduces the modeling results of the energy absorbed by different lattice cells topologies under impacts

The onset of the GeV afterglow of GRB 090510

We study the emission of the short/hard GRB 090510 at energies > 0.1 GeV as observed by the Large Area Telescope (LAT) onboard the Fermi satellite. The GeV flux rises in time as t^2 and decays as t^-1.5 up to 200 s. The peak of the high energy flux is delayed by 0.2 s with respect to the main ~MeV pulse detected by the Fermi Gamma Burst Monitor (GBM). Its energy spectrum is consistent with F(E)=E^-1. The time behavior and the spectrum of the high energy LAT flux are strong evidences of an afterglow origin. We then interpret it as synchrotron radiation produced by the forward shock of a fireball having a bulk Lorentz factor Gamma ~ 2000. The afterglow peak time is independent of energy in the 0.1-30 GeV range and coincides with the arrival time of the highest energy photon (~ 30 GeV). Since the flux detected by the GBM and the LAT have different origins, the delay between these two components is not entirely due to possible violation of the Lorentz invariance. It is the LAT component by itself that allows to set a stringent lower limit on the quantum-gravity mass of 4.7 times the Planck mass.Comment: 4 pages, 3 figures, submitted to ApJ Letter