1,711 research outputs found
Lithographically printed voltaic cells - A feasibility study
It has been shown that circuit interconnects and various passive components can be fabricated on a variety of flexible substrates using the offset lithographic process. This paper reports on a feasibility study investigating the manufacture of voltaic cells deposited via offset lithography
Development and characterisation of lithographically printed voltaic cells
This paper reports progress in the fabrication of voltaic cells and batteries via offset lithographic printing. Successful design and manufacture of lithographically printed voltaic cells would facilitate the integration of printed passive components, interconnects and display elements for disposable electronics in low-volume, low weight circuits and systems. The conductive lithographic film (CLF) printing process was developed by Brunel University to fabricate circuit interconnect and various passive components at high speed and low cost. A feasibility study, investigating printed cells based on zinc-carbon electrochemistry, is described. This has resulted in the production of a printed battery able to power a microcontroller-driven LED display system for more than three hours. Further work seeks to improve cell capacity, address manufacturing process issues, and characterise the structures in more detail
Electroluminescent light sources via soft lithography
Purpose: Microcontact printing is a process used to print high resolution protein arrays for biosensors. We investigate using these techniques to print electrically conductive fine line structures for electroluminescent (E/L) light sources.
Approach: The viability of using microcontact printing as a process for electronics fabrication is investigated. Polydimethylsiloxane (PDMS) stamps inked with alkanethiol compounds form Self Assembled Monolayers (SAM) on substrate surfaces, acting as the resist to subsequent etching processes. The printed lines are characterized with regard to their performance as high electric field generators in electroluminescent displays.
Findings: It has been demonstrated that microcontact printing is a cheap, repeatable process for fabricating electronic devices. The results demonstrate the viability of the process to fabricate electric field generator structures for E/L light sources with reduced driving voltages.
Value: It has been demonstrated that microcontact printing can produce electrically conductive fine-line structures with high resolution, confirming its viability in printed electronics manufacture
Recommended from our members
A time-strain monitoring system fabricated via offset lithographic printing
This paper reports progress in the development of strain sensors fabricated using the Conductive Lithographic Film (CLF) printing process. Strain sensitive structures printed via an unmodified offset lithographic printing press using a silver loaded conductive ink have been deposited concurrently with circuit interconnect, to form an electronic smart packaging system. A system populated with SMT components has proven successful in interpreting and logging deformation incidences subjected to a package during testing. It is proposed that with further development such a system could be printed in sync with packaging graphics using a single printing process to form an integrated time ā strain monitoring system
Characterization of lithographically printed resistive strain gauges
This paper reports progress in sensor fabrication by the conductive lithographic film (CLF) printing process. Work describing strain-sensitive structures manufactured using a modified printing process and conductive inks is addressed. The performance of a "single-ink" strain-sensitive structure when printed on six alternative substrates (GlossArt, PolyArt, Teslin, Mylar C, Melinex, and Kapton) is analyzed. Though not intending to compete with conventional gauges in high-tolerance measurement, the structures exhibit properties that indicate suitability for novel applications
Conductive lithographic film fabricated resistive strain gauges
This paper reports progress in sensor fabrication by the conductive lithographic film (CLF) printing process. Work describing strain sensitive structures manufactured using a modified printing process and conductive inks are addressed. The performance of a 'single ink' strain sensitive structure when printed on six alternative polymer substrates (GlossArt, PolyArt, Teslin, Mylar C, Mylar and Kapton) is analysed. Though not intending to compete with conventional gauges in high tolerance measurement, the structures exhibit properties that indicate suitability for novel applications
Printed thermocouple devices
A novel process for the fabrication of thermocouples using thick-film techniques has been developed. Thermoelectric reactions of 22 Ī¼V/Ā°C per couple have been observed which are comparable to those of conventional thermocouples.
This work outlines the potential for a rapid, lowcost, low temperature manufacturing solution for the production of electrical temperature sensors
The response of a floating ice sheet to an accelerating line load
The two-dimensional response of a thin, floating sheet of ice to a line load that accelerates from rest at to a uniform velocity V for is determined through an integral-transform solution of the linearized equations of motion. If ā i.e. if the load is impulsively started with velocity V ā the solution exhibits singularities at , the shallow-water-gravity-wave speed, and , the minimum speed for transverse motion of the ice, but these singularities are avoided by the acceleration of the load through the critical speeds
Global data for ecology and epidemiology: a novel algorithm for temporal Fourier processing MODIS data
Background. Remotely-sensed environmental data from earth-orbiting satellites are increasingly used to model the distribution and abundance of both plant and animal species, especially those of economic or conservation importance. Time series of data from the MODerate-resolution Imaging Spectroradiometer (MODIS) sensors on-board NASA's Terra and Aqua satellites offer the potential to capture environmental thermal and vegetation seasonality, through temporal Fourier analysis, more accurately than was previously possible using the NOAA Advanced Very High Resolution Radiometer (AVHRR) sensor data. MODIS data are composited over 8- or 16-day time intervals that pose unique problems for temporal Fourier analysis. Applying standard techniques to MODIS data can introduce errors of up to 30% in the estimation of the amplitudes and phases of the Fourier harmonics. Methodology/Principal Findings. We present a novel spline-based algorithm that overcomes the processing problems of composited MODIS data. The algorithm is tested on artificial data generated using randomly selected values of both amplitudes and phases, and provides an accurate estimate of the input variables under all conditions. The algorithm was then applied to produce layers that capture the seasonality in MODIS data for the period from 2001 to 2005. Conclusions/Significance. Global temporal Fourier processed images of 1 km MODIS data for Middle Infrared Reflectance, day- and night-time Land Surface Temperature (LST), Normalised Difference Vegetation Index (NDVI), and Enhanced Vegetation Index (EVI) are presented for ecological and epidemiological applications. The finer spatial and temporal resolution, combined with the greater geolocational and spectral accuracy of the MODIS instruments, compared with previous multi-temporal data sets, mean that these data may be used with greater confidence in species' distribution modelling
- ā¦