Altitude-Wind-Tunnel Investigation of Oil-System Performance of XR-4360-8 Engine in XTB2D-1 Airplane

An investigation was conducted in the Cleveland altitude wind tunnel to determine the aerodynamic characteristics and the oil delivery critical altitude of the oil-cooler installation of an XTB2D-1 airplane. The investigation was made with the propeller removed end with the engine operating at 1800 brake horsepower, an altitude of 15,000 feet (except for tests of oil-delivery critical altitude), oil-cooler flap deflections from -20 degrees to 20 degrees and inclinations of the thrust axis of 0 degrees, 1.5 degrees, and 6 degrees. At an inclination of the thrust axis of 0 degrees and with the propeller operating, the total-pressure recovery coefficient at the face of the oil cooler varied from 0.84 to 1.10 depending on the flap deflection. With the propeller removed, the best pressure recovery at the face of the oil cooler was obtained at an inclination of the thrust axis of 1.5 degrees. Air-flow separation occurred on the inner surface of the upper lip of the oil-cooler duct inlet at an inclination of the thrust axis of 0 degrees and on the inner surface of the lower lip at 6 degrees. Static pressure coefficients over the duct lips were sufficiently low that no trouble from compressibility would be encountered in level flight. The oil-delivery critical altitude at cruising power (2230 rpm, 1675 bhp) was approximately 18,500 feet for the oil system tested

Photographic Study of Liquid-Oxygen Boiling and Gas Injection in the Injector of a Chugging Rocket Engine

High-speed motion pictures were taken of conditions in the injector liquid-oxygen cavity of an RL-10 rocket engine during throttled engine operation. Photographs were taken during operation of the engine in the chugging region as the helium gas was injected to stabilize combustion, during operation at rated thrust, and during transition into chugging conditions as the gas injection was discontinued. Results of the investigation indicate that, during chugging rocket operation of the RL-10 engine, a high population of fairly large bubbles formed and collapsed within the liquid-oxygen cavity at the same frequency as the chamber pressure oscillations. When gaseous helium was injected into the liquid-oxygen cavity, a fog rapidly spread over the entire field of view, and the system immediately became stable. The injection of gaseous helium at rated conditions produced a very slight increase in engine performance but not enough to produce a net gain in a typical mission payload with the extra equipment needed. The inherent low-frequency system instability associated with the fuel system at low thrust levels was reduced by injecting either gaseous helium or hydrogen. Complete stabilization was achieved in some cases, and a reduction in the severity of the oscillations in others. This was apparently due to the anchoring of the phase change front to the location of the gas injection

A Study of the Decarboxylation of Trichloroacetic Acid in Solutions of Water and Dimethylsulfoxide

Author Institution: Department of Physical Science, Denison University, Granville, OhioThe decarboxylation of trichloroacetic acid has been found to occur readily at temperatures as low as 25.0°C in the presence of dimethylsulfoxide in water solutions, a fact not previously reported in chemical literature. The reaction rate is dependent upon the concentration of the dimethylsulfoxide. The reaction rate constant increases about sixty percent as the concentration of dimethylsulfoxide (DMSO) is increased from c. 50 percent to c. 86 percent. The reaction is first order and the rate is also influenced by the actual concentration of the trichloroacetate ion. An effect of the DMSO is to increase the concentration of this ion. The paper presents density curves at 20.00°C and 25.00°C (each±0.05 °C) for solutions of DMSO in water

Altitude Performance and Operational Characteristics of 29-inch-diameter Tail-pipe Burner with Several Fuel Systems and Flame Holders on J35 Turbojet Engine

An investigation of turbojet-engine thrust augmentation by means of tail-pipe burning has been conducted in the NACA Lewis altitude wind tunnel. Several fuel systems and flame holders were investigated in a 29-inch-diameter tail-pipe burner to determine the effect of fuel distribution and flame-holder design on tail-pipe-burner performance and operational characteristics over a range of simulated flight conditions. At an altitude of 5000 feet, the type of flame holder used had only a slight effect on the combustion efficiency. As the altitude was increased, the decrease in peak combustion efficiency became more rapid as the blocking area of the flame holder was reduced. At all altitudes investigated, an improvement in the uniformity of the radial distribution of fuel and air slightly increased the peak combustion efficiencies and shifted the peak combustion efficiency to higher tail-pipe fuel-air ratios. The use of an internal cooling liner extending the full length of the tail-pipe combustion chamber provided adequate shell cooling at all flight conditions investigated

Altitude-wind-tunnel Investigation of J47 Turbojet-engine Performance

An investigation has been conducted in the NACA Lewis altitude wind tunnel to evaluate the performance of the J47 turbojet engine over a range of simulated altitudes from 5000 to 50,000 feet, simulated flight Mach numbers from 0.21 to 0.97, and a complete range of engine speeds. Data are presented to show the effects of altitude at a flight Mach number of 0.21 and of flight Mach number at an altitude of 25,000 feet. The performance data are generalized by two methods to determine the range of flight conditions for which engine performance may be predicted from performance data obtained at a given flight condition

Investigation of Effects of Inlet-air Velocity Distortion on Performance of Turbojet Engine

To determine effect of nonuniform inlet-air velocities, a full scale, axial-flow turbojet engine was investigated in Lewis altitude wind tunnel at altitudes from 20,000 to 50,000 feet, 0.21 flight Mach number and corrected engine speeds from 77.3 percent of rated speed to rated speed. Total-pressure variations as large as 103 pounds per square foot in radial direction and 90 pounds per square foot in circumferential direction at 30,000 feet were obtained. With the distortions investigated, net thrust varied between 0.95 and 1.03 of the thrust with uniform inlet-air distribution. Similarly the ratio of specific fuel consumption varied from 1.00 to 1.04. Within the arrange of this investigation the effects of nonuniform inlet velocity were not serious for the engine investigated