A model for the domestication of Panicum miliaceum (common, proso or broomcorn millet) in China

This paper outlines a model for the domestication of Panicum miliaceum (broomcorn millet) in Northern China. Data from 43 archaeological sites indicate a continuous increase in average grain size between 6000 and 3300 BC. After this date there is a divergence, with grain size continuing to increase in some populations, while others show no further size increase. The initial increase in grain size is attributed to selection during domestication, while later divergence after 3300 BC is interpreted as resulting from post-domestication selection. Measurements of grains from two archaeological populations of P. ruderale, showed grains were longer in length by 3300 BC than the earliest grains of P. miliaceum. This suggests this sub-species includes many feral, weedy and/or introgressed forms of P. miliaceum and therefore is probably not entirely representative of the true wild ancestor. It is argued that changes from shattering to non-shattering are contemporary with increasing grain size and the commencement of cultivation. The window of P. miliaceum domestication is therefore likely to lie between 7000 and 3300 BC. However, it is probable that a lengthy period of millet harvesting and small-scale management preceded its domestication

Apremilast monotherapy in DMARD-naive psoriatic arthritis patients: Results of the randomized, placebocontrolled PALACE 4 trial

Objectives. The PALACE 4 trial evaluated apremilast monotherapy in patients with active PsA who were DMARD-naive. Methods. Eligible patients were randomized (1:1:1) to placebo, apremilast 20mg twice a day or apremilast 30mg twice a day. At week 16 or 24, placebo patients were rerandomized to apremilast. Double-blind apremilast treatment continued to week 52, with extension up to 4 years. The primary endpoint was the proportion of patients achieving ≥20% improvement in ACR response criteria (ACR20) at week 16; secondary endpoints included the mean change in the HAQ Disability Index (HAQ-DI) score at week 16. Results. A total of 527 patients with mean disease duration of 3.4 years and high disease activity were randomized and received treatment. More apremilast patients achieved ACR20 response at week 16 [placebo, 15.9%; 20 mg, 28.0% (P = 0.0062); 30 mg, 30.7% (P = 0.0010)]. The mean HAQ-DI improvements were -0.17 (20 mg; P = 0.0008) and -0.21 (30 mg; P<0.0001) vs 0.03 (placebo). Both apremilast doses showed significant ACR50 responses vs placebo at week 16 and improvements in secondary efficacy measures (swollen/tender joint counts) and psoriasis assessments, with sustained improvements through week 52. Common adverse events (AEs) over 52 weeks were diarrhoea, nausea, headache and upper respiratory tract infection; most events were mild or moderate. Serious AEs and AEs leading to discontinuation were comparable between groups. Laboratory abnormalities were infrequent and transient. Conclusions. In DMARD-naive patients, apremilast monotherapy improved PsA signs/symptoms over 52 weeks and was generally well tolerated

Bioconjugates of Glucose Oxidase and Gold Nanorods Based on Electrostatic Interaction with Enhanced Thermostability

Bioconjugates made up of an enzyme and gold nanorods (GNRs) were fabricated by electrostatic interactions (layer-by-layer method, LBL) between anionic glucose oxidase (GOD) and positively charged GNRs. The assembled processes were monitored by UV–Vis spectra, zeta potential measurements, and transmission electron microscopy. The enzyme activity assays of the obtained bioconjugates display a relatively enhanced thermostability behavior in contrast with that of free enzyme. Free GOD in solution only retains about 22% of its relative activity at 90 °C. Unexpectedly, the immobilized GOD on GNRs still retains about 39.3% activity after the same treatment. This work will be of significance for the biologic enhancement using other kinds of anisotropic nanostructure and suggests a new way of enhancing enzyme thermostability using anisotropic metal nanomaterials

Effect of ZnCdTe-Alloyed Nanocrystals on Polymer–Fullerene Bulk Heterojunction Solar Cells

The photovoltaic properties of solar cell based on the blends of poly[2-methoxy-5-(2-ethylhexoxy-1,4-phenylenevinylene) (MEH-PPV), fullerene (C60), and ZnCdTe-alloyed nanocrystals were investigated. Comparing the spectral response of photocurrent of the MEH-PPV:C60(+ZnCdTe) nanocomposite device with that of the devices based on MEH-PPV:C60and pristine MEH-PPV, one can find that the nanocomposite device exhibits an enhanced photocurrent. In comparing the composite devices with different ZnCdTe:[MEH-PPV + C60] weight ratios of 10 wt% (D1–1), 20 wt% (D1–2), 40 wt% (D1–3), and 70 wt% (D1–4), it was found that the device D1–3exhibits the best performance. The power conversion efficiency (η) is improved doubly compared with that of the MEH-PPV:C60device

Performance evaluation on an air-cooled heat exchanger for alumina nanofluid under laminar flow

This study analyzes the characteristics of alumina (Al2O3)/water nanofluid to determine the feasibility of its application in an air-cooled heat exchanger for heat dissipation for PEMFC or electronic chip cooling. The experimental sample was Al2O3/water nanofluid produced by the direct synthesis method at three different concentrations (0.5, 1.0, and 1.5 wt.%). The experiments in this study measured the thermal conductivity and viscosity of nanofluid with weight fractions and sample temperatures (20-60°C), and then used the nanofluid in an actual air-cooled heat exchanger to assess its heat exchange capacity and pressure drop under laminar flow. Experimental results show that the nanofluid has a higher heat exchange capacity than water, and a higher concentration of nanoparticles provides an even better ratio of the heat exchange. The maximum enhanced ratio of heat exchange and pressure drop for all the experimental parameters in this study was about 39% and 5.6%, respectively. In addition to nanoparticle concentration, the temperature and mass flow rates of the working fluid can affect the enhanced ratio of heat exchange and pressure drop of nanofluid. The cross-section aspect ratio of tube in the heat exchanger is another important factor to be taken into consideration

Validation of the psychometric properties of the health-promoting lifestyle profile in a sample of Taiwanese women

PURPOSE: To examine the preliminary psychometric properties of the Chinese health-promoting lifestyle profile II (HPLP II) among Taiwanese women. METHODS: We conducted a secondary analysis of cross-sectional data from 137 middle-aged women in southern Taiwan. HPLP II reliability was estimated with Cronbach's alpha coefficient, and concurrent validity was estimated with Pearson's correlation between the HPLP II, the World Health Organization's abbreviated Quality of Life assessment (WHOQOL-BREF), perceived health, and demographic variables. Confirmatory factor analysis (CFA) evaluated construct validity. RESULTS: Initial CFA using a six-factor measurement model aligned with the original HPLP II, excepting the factor loading of one subsequently excluded item. CFA of the revised 51-item HPLP II yielded a good estimate of fit. Correlations between the revised instrument and the six subscales were acceptable >0.7. The Cronbach's alpha coefficient surpassed 0.7 for the revised instrument and six subscales ranged from 0.71 to 0.91. The relationships between the 51-item instrument, perceived health, WHOQOL-BREF domain scores, and demographic variables were also significantly positive. CONCLUSIONS: The revised HPLP II scale is appropriate to measure the health-promoting lifestyles of Taiwanese women.published_or_final_versionSpringer Open Choice, 21 Feb 201

Direct patterning of gold nanoparticles using flexographic printing for biosensing applications

In this paper, we have presented the use of flexographic printing techniques in the selective patterning of gold nanoparticles (AuNPs) onto a substrate. Highly uniform coverage of AuNPs was selectively patterned on the substrate surface, which was subsequently used in the development of a glucose sensor. These AuNPs provide a biocompatible site for the attachment of enzymes and offer high sensitivity in the detection of glucose due to their large surface to volume ratio. The average size of the printed AuNPs is less than 60 nm. Glucose sensing tests were performed using printed carbon-AuNP electrodes functionalized with glucose oxidase (GOx). The results showed a high sensitivity of 5.52 μA mM−1 cm−2 with a detection limit of 26 μM. We have demonstrated the fabrication of AuNP-based biosensors using flexographic printing, which is ideal for low-cost, high-volume production of the devices

The Transcriptome of the Nosocomial Pathogen Enterococcus faecalis V583 Reveals Adaptive Responses to Growth in Blood

gains access to the bloodstream and establishes a persistent infection is not well understood.. infections

Lattice Boltzmann simulation of alumina-water nanofluid in a square cavity

A lattice Boltzmann model is developed by coupling the density (D2Q9) and the temperature distribution functions with 9-speed to simulate the convection heat transfer utilizing Al2O3-water nanofluids in a square cavity. This model is validated by comparing numerical simulation and experimental results over a wide range of Rayleigh numbers. Numerical results show a satisfactory agreement between them. The effects of Rayleigh number and nanoparticle volume fraction on natural convection heat transfer of nanofluid are investigated in this study. Numerical results indicate that the flow and heat transfer characteristics of Al2O3-water nanofluid in the square cavity are more sensitive to viscosity than to thermal conductivity