5 research outputs found
Stabilising effect of α-lactalbumin on concentrated infant milk formula emulsions heat treated pre- or post-homogenisation
peer-reviewedProtein type and/or heat treatment pre- or post-homogenisation can affect the physical stability of infant formulations during manufacture. Previous research has described the use of α-lactalbumin addition in infant formulae, but has not demonstrated the effect of heating pre- or post-emulsion formulation during processing. The objective of this study was to evaluate the effect of both of these parameters. Three batches of model 1st-stage infant formula containing differing whey protein ratios (60:40 whey: casein with α-lactalbumin content 12, 30 or 48% of total protein) were prepared. Each batch was split; one half receiving heat treatment pre-homogenisation and the second half homogenised and then heat treated. Emulsion stability was determined by size exclusion chromatography, SDS-PAGE, particle size and viscosity measurements. There was a significant (P < 0.05) reduction in the formation of large soluble aggregates upon increasing α-lac concentration in emulsions heat treated either before or after homogenisation. Heat treatment of formulations post-homogenisation resulted in a higher (P < 0.05) D.v09 within the particle size distribution; increasing α-lactalbumin concentration to 30 or 48% significantly (P < 0.05) reduced the D.v09 within the particle size distribution in these emulsions. The viscosity of concentrates (55 % total solids) containing the 12% α-lactalbumin, heat treated post-homogenisation, was significantly greater (P < 0.05) than the equivalent emulsion heat treated pre-homogenisation; increasing the α-lactalbumin concentration to 30 or 48% significantly (P < 0.05) reduced viscosity. When the α-lactalbumin content was increased to 48% as a percentage of the total protein, heating before or after emulsion formation had no effect on concentrate viscosity. The findings demonstrate the importance of thermal denaturation/aggregation of whey proteins (and in particular, the ratio of α-lactalbumin to β-lactoglobulin) prior to homogenisation of infant formula emulsions
Pilot-scale formation of whey protein aggregates determine the stability of heat-treated whey protein solutions—Effect of pH and protein concentration
peer-reviewedDenaturation and consequent aggregation in whey protein solutions is critical to product functionality during processing. Solutions of whey protein isolate (WPI) prepared at 1, 4, 8, and 12% (wt/wt) and pH 6.2, 6.7, or 7.2 were subjected to heat treatment (85°C × 30 s) using a pilot-scale heat exchanger. The effects of heat treatment on whey protein denaturation and aggregation were determined by chromatography, particle size, turbidity, and rheological analyses. The influence of pH and WPI concentration during heat treatment on the thermal stability of the resulting dispersions was also investigated. Whey protein isolate solutions heated at pH 6.2 were more extensively denatured, had a greater proportion of insoluble aggregates, higher particle size and turbidity, and were significantly less heat-stable than equivalent samples prepared at pH 6.7 and 7.2. The effects of WPI concentration on denaturation/aggregation behavior were more apparent at higher pH where the stabilizing effects of charge repulsion became increasingly influential. Solutions containing 12% (wt/wt) WPI had significantly higher apparent viscosities, at each pH, compared with lower protein concentrations, with solutions prepared at pH 6.2 forming a gel. Smaller average particle size and a higher proportion of soluble aggregates in WPI solutions, pre-heated at pH 6.7 and 7.2, resulted in improved thermal stability on subsequent heating. Higher pH during secondary heating also increased thermal stability. This study offers insight into the interactive effects of pH and whey protein concentration during pilot-scale processing and demonstrates how protein functionality can be controlled through manipulation of these factors
The effects of sequential heat treatment on microbial reduction and spore inactivation during milk processing
peer-reviewedSequential heating processes are commonly applied to milk by the dairy industry as part of their microbiological control strategy. Often pasteurisation at 72 °C is followed by a sequential high heat treatment step of up to 125 °C; however, such severe heat treatment can lead to reduced protein quality. Nine temperature combinations (80–90 °C) were evaluated to assess microbial reduction and whey protein nitrogen index values during pilot scale milk processing. A total of 110 bacterial isolates were identified to species level by 16S rDNA sequencing, with Bacillus licheniformis identified as the dominant species. While the experimental treatments did not achieve microbial reductions comparable with the control heating process, the results of this study provide a benchmark for milk processors relative to the effects of sequential heat treatments on milk and their impact on the survival of both thermally resistant microbial populations and thermally labile milk components during processing.Department of Agriculture, Food and the Marine, Irelan
Pilot-scale formation of whey protein aggregates determine the stability of heat-treated whey protein solutions—Effect of pH and protein concentration
Denaturation and consequent aggregation in whey protein solutions is critical to product functionality during processing. Solutions of whey protein isolate (WPI) prepared at 1, 4, 8, and 12% (wt/wt) and pH 6.2, 6.7, or 7.2 were subjected to heat treatment (85°C × 30 s) using a pilot-scale heat exchanger. The effects of heat treatment on whey protein denaturation and aggregation were determined by chromatography, particle size, turbidity, and rheological analyses. The influence of pH and WPI concentration during heat treatment on the thermal stability of the resulting dispersions was also investigated. Whey protein isolate solutions heated at pH 6.2 were more extensively denatured, had a greater proportion of insoluble aggregates, higher particle size and turbidity, and were significantly less heat-stable than equivalent samples prepared at pH 6.7 and 7.2. The effects of WPI concentration on denaturation/aggregation behavior were more apparent at higher pH where the stabilizing effects of charge repulsion became increasingly influential. Solutions containing 12% (wt/wt) WPI had significantly higher apparent viscosities, at each pH, compared with lower protein concentrations, with solutions prepared at pH 6.2 forming a gel. Smaller average particle size and a higher proportion of soluble aggregates in WPI solutions, pre-heated at pH 6.7 and 7.2, resulted in improved thermal stability on subsequent heating. Higher pH during secondary heating also increased thermal stability. This study offers insight into the interactive effects of pH and whey protein concentration during pilot-scale processing and demonstrates how protein functionality can be controlled through manipulation of these factors