An approach to optimization of low-power Stirling cryocoolers

A method for optimizing the design (shape of the displacer) of low power Stirling cryocoolers relative to the power required to operate the systems is described. A variational calculation which includes static conduction, shuttle and radiation losses, as well as regenerator inefficiency, was completed for coolers operating in the 300 K to 10 K range. While the calculations apply to tapered displacer machines, comparison of the results with stepped displacer cryocoolers indicates reasonable agreement

Contribution of thermal noise to the line width of Josephson radiation from superconducting point contacts

Contribution of thermal noise to line width of Josephson radiation from superconducting point contact

Analysis of MMIC arrays for use in the ACTS Aero Experiment

The Aero Experiment is designed to demonstrate communication from an aircraft to an Earth terminal via the ACTS. This paper describes the link budget and antenna requirements for a 4.8 kbps full-duplex voice link at Ka-Band frequencies. Three arrays, one transmit array developed by TI and two receive arrays developed by GE and Boeing, were analyzed. The predicted performance characteristics of these arrays are presented and discussed in the paper

Ceramic-ceramic shell tile thermal protection system and method thereof

A ceramic reusable, externally applied composite thermal protection system (TPS) is proposed. The system functions by utilizing a ceramic/ceramic upper shell structure which effectively separates its primary functions as a thermal insulator and as a load carrier to transmit loads to the cold structure. The composite tile system also prevents impact damage to the atmospheric entry vehicle thermal protection system. The composite tile comprises a structurally strong upper ceramic/ceramic shell manufactured from ceramic fibers and ceramic matrix meeting the thermal and structural requirements of a tile used on a re-entry aerospace vehicle. In addition, a lightweight high temperature ceramic lower temperature base tile is used. The upper shell and lower tile are attached by means effective to withstand the extreme temperatures (3000 to 3200F) and stress conditions. The composite tile may include one or more layers of variable density rigid or flexible thermal insulation. The assembly of the overall tile is facilitated by two or more locking mechanisms on opposing sides of the overall tile assembly. The assembly may occur subsequent to the installation of the lower shell tile on the spacecraft structural skin

Polymer matrix and graphite fiber interface study

Hercules AS4 graphite fiber, unsized, or with EPON 828, PVA, or polysulfone sizing, was combined with three different polymer matrices. These included Hercules 3501-6 epoxy, Hercules 4001 bismaleimide, and Hexcel F155 rubber toughened epoxy. Unidirectional composites in all twelve combinations were fabricated and tested in transverse tension and axial compression. Quasi-isotropic laminates were tested in axial tension and compression, flexure, interlaminar shear, and tensile impact. All tests were conducted at both room temperature, dry and elevated temperature, and wet conditions. Single fiber pullout testing was also performed. Extensive scanning electron microphotographs of fracture surfaces are included, along with photographs of single fiber pullout failures. Analytical/experimental correlations are presented, based on the results of a finite element micromechanics analysis. Correlations between matrix type, fiber sizing, hygrothermal environment, and loading mode are presented. Results indicate that the various composite properties were only moderately influenced by the fiber sizings utilized

Simulated Radioisotope Thrust System and Component Development Final Report

Electrically heated and radioisotope heated thrusters for satellite attitude control and stationkeepin

Multi-Temperature Blackbody Spectra of Thin Accretion Disks With and Without a Zero-Torque Inner Boundary Condition

The standard spectral model for analyzing the soft component of thermal emission from a thin accretion disk around a black hole is the multi-temperature blackbody (MTB) model. The widely used implementation of this model, which is known as ``diskbb,'' assumes nonzero torque at the inner edge of the accretion disk. This assumption is contrary to the classic and current literature on thin-disk accretion, which advocates the use of a zero-torque boundary condition. Consequently, we have written code for a zero-torque model, ``ezdiskbb,'' which we compare to the nonzero-torque model diskbb by fitting RXTE spectra of three well-known black hole binaries: 4U 1543-47, XTE J1550-564, and GRO J1655-40. The chief difference we find is that the zero-torque model gives a value for the inner disk radius that is about 2.2 times smaller than the value given by diskbb. This result has important implications, especially for the determination of black-hole angular momentum and mass accretion rate.Comment: 27 pages, 9 figures, submitted to Ap

Pressure buildup during CO2 injection in brine aquifers using the Forchheimer equation

If geo-sequestration of CO2 is to be employed as a key emissions reduction method in the global effort to mitigate climate change, simple yet robust screening of the risks of disposal in brine aquifers will be needed. There has been significant development of simple analytical and semi-analytical techniques to support screening analysis and performance assessment for potential carbon sequestration sites. These techniques have generally been used to estimate the size of CO2 plumes for the purpose of leakage rate estimation. A common assumption has been that both the fluids and the geological formation are incompressible. Consequently, calculation of pressure distribution requires the specification of an arbitrary radius of influence. In this talk, a new similarity solution is derived using the method of matched asymptotic expansions. By allowing for slight compressibility in the fluids and formation, the solution improves on previous work by not requiring the specification of an arbitrary radius of influence. A large-time approximation of the solution is then extended to account for non-Darcy inertial effects using the Forchheimer equation. Both solutions are verified by comparison with finite difference solutions. The results show that inertial losses will often be comparable, and sometimes greater than, the viscous Darcy-like losses associated with the brine displacement, although this is strongly dependent on formation porosity and permeability

Preliminary floor, seat, and dummy data

According to preliminary examination of the data, out of 179 data channels that were onboard the aircraft in support of the seat experiments, there is data from 168. There was somewhat more severe environment imposed in the structure of the obstacles than by the ground impact. Therefore, both ground impact and obstacle impact are of interest for crashworthiness experiments. Most of the data channels that were studied are fairly consistent with the physical evidence: they show acceleration levels that are reasonable, and in many cases these integrate out to a reasonable velocity change. Finally, from observation thus far, the ground impact did not fail or significantly damage any seat. Nor did any of the energy absorbers in the modified seats extend. The accelerations do not appear high enough and/or energetic enough to cause this to happen. At this time, the onboard films have not been studied; only some videotape have been viewed. Some of the seats were so badly damaged by the fire that any failures which might have occurred were obscured. A close examination of the onboard films using a stop-action projector will allow a more thorough evaluation

Coal-shale interface detection system

A coal-shale interface detection system for use with coal cutting equipment consists of a reciprocating hammer on which an accelerometer is mounted to measure the impact of the hammer as it penetrates the ceiling or floor surface of a mine. A pair of reflectometers simultaneously view the same surface. The outputs of the accelerometer and reflectometers are detected and jointly registered to determine when an interface between coal and shale is being cut through