Effect of heat treatment and drawing on high-manganese steel pipe welded by gas tungsten arc

This study investigated the effect of post-weld processes including annealing and drawing on the microstructure and mechanical properties of high-Mn steel pipes welded by gas tungsten arc welding. The weld metal showed a solidified microstructure having coarse and elongated grains due to coalescence of columnar dendrite into welding heat direction. After post-annealing, the solidified microstructure changed into equiaxed grains due to recrystallization and grain growth. Mn segregation occurred during welding solidification and caused lower stacking fault energy (SFE) in the Mn-depleted region. Although epsilon-martensite formation in the as-welded state and during deformation was expected due to decreased SFE of the Mn-depleted zone, all regions showed a fully austenitic phase. The annealing process decreased strength due to grain coarsening but increased ductility. The drawing process increased strength of weld metal through work hardening. All pipes showed decreasing strain rate sensitivity (SRS) with deformation and negative SRS after certain strain levels. It was confirmed that negative SRS is related to less formation of mechanical twinning at a higher strain rate. This work provides fundamental insights into manufacturing a high-Mn steel pipe and manipulating its properties with annealing and drawing processes

Sphingosylphosphorylcholine inhibits plasma cell differentiation and ameliorates experimental autoimmune encephalomyelitis

IntroductionMultiple sclerosis (MS) is a potentially disabling disease that damages the brain and spinal cord, inducing paralysis of the body. While MS has been known as a T-cell mediated disease, recent attention has been drawn to the involvement of B cells in its pathogenesis. Autoantibodies from B cells are closely related with the damage lesion of central nervous system and worse prognosis. Therefore, regulating the activity of antibody secreting cell could be related with the severity of the MS symptoms.MethodsTotal mouse B cells were stimulated with LPS to induce their differentiation into plasma cells. The differentiation of plasma cells was subsequently analyzed using flow cytometry and quantitative PCR analysis. To establish an experimental autoimmune encephalomyelitis (EAE) mouse model, mice were immunized with MOG35–55/CFA emulsion.ResultsIn this study, we found that plasma cell differentiation was accompanied by upregulation of autotaxin, which converts sphingosylphosphorylcholine (SPC) to sphingosine 1-phosphate in response to LPS. We observed that SPC strongly blocked plasma cell differentiation from B cells and antibody production in vitro. SPC downregulated LPS-stimulated IRF4 and Blimp 1, which are required for the generation of plasma cells. SPC-induced inhibitory effects on plasma cell differentiation were specifically blocked by VPC23019 (S1PR1/3 antagonist) or TY52159 (S1PR3 antagonist), but not by W146 (S1PR1 antagonist) and JTE013 (S1PR2 antagonist), suggesting a crucial role of S1PR3 but not S1PR1/2 in the process. Administration of SPC against an EAE mouse model significantly attenuated the symptoms of disease, showing decreased demyelinated areas of the spinal cord and decreased numbers of cells infiltrated into the spinal cord. SPC markedly decreased plasma cell generation in the EAE model, and SPC-induced therapeutic effects against EAE were not observed in μMT mice.ConclusionCollectively, we demonstrate that SPC strongly inhibits plasma cell differentiation, which is mediated by S1PR3. SPC also elicits therapeutic outcomes against EAE, an experimental model of MS, suggesting SPC as a new material to control MS

Pathogenesis of Korean SapelovirusA in piglets and chicks.

Sapelovirus A (SV-A), formerly known as porcine sapelovirus as a member of a new genus Sapelovirus, is known to cause enteritis, pneumonia, polioencephalomyelitis and reproductive disorders in pigs. We have recently identified α2,3-linked sialic acid on GD1a ganglioside as a functional SV-A receptor rich in the cells of pigs and chickens. However, the role of GD1a in viral pathogenesis remains elusive. Here, we demonstrated that a Korean SV-A strain could induce diarrhoea and intestinal pathology in piglets but not in chicks. Moreover, this Korean SV-A strain had mild extra-intestinal tropisms appearing as mild, non-suppurative myelitis, encephalitis and pneumonia in piglets, but not in chicks. By real-time reverse transcription (RT) PCR, higher viral RNA levels were detected in faecal samples than in sera or extra-intestinal organs from virus-inoculated piglets. Immunohistochemistry confirmed that high viral antigens were detected in the epithelial cells of intestines from virus-inoculated piglets but not from chicks. This Korean SV-A strain could bind the cultured cell lines originated from various species, but replication occurred only in cells of porcine origin. These data indicated that this Korean SV-A strain could replicate and induce pathology in piglets but not in chicks, suggesting that additional porcine-specific factors are required for virus entry and replication. In addition, this Korean SV-A strain is enteropathogenic, but could spread to the bloodstream from the gut and disseminate to extra-intestinal organs and tissues. These results will contribute to our understanding of SV-A pathogenesis so that efficient anti-sapelovirus drugs and vaccines could be developed in the future.This study was supported by a grant (2014R1A2A2A01004292) of the Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Science, ICT and Future Planning, Bio-industry Technology Development Program (315021-04) through the Korea Institute of Planning and Evaluation for Technology in Food, Agriculture, Forestry and Fisheries (iPET) funded by the Ministry of Agriculture, Food and Rural Affairs, and Korea Basic Science Institute grant (C33730), Republic of Korea. IG is a Wellcome Senior Fellow supported by the Wellcome Trust (097997/Z/11/Z). Chonnam National University provided funding to Mun-Il Kang (2012). The Mab against SV-A capsid protein was received as a generous gift from Dr. M. Dauber (Friedrich-Loeffler Institute, Germany).This is the accepted version of the article. The final version is available from the Microbiology Society via http://dx.doi.org/10.1099/jgv.0.00057

Transient voltage control of a DFIG-based wind power plant for suppressing overvoltage using a reactive current reduction loop

This paper proposes a transient voltage control scheme of a doubly fed induction generator (DFIG)-based wind power plant (WPP) using a reactive current reduction loop to suppress the overvoltage at a point of interconnection (POI) and DFIG terminal after a fault clearance. The change of terminal voltage of a DFIG is monitored at every predefined time period to detect the fault clearance. If the voltage change exceeds a set value, then the reactive current reduction loop reduces the reactive current reference in the DFIG controller using the step function. The reactive current injection of DFIGs in a WPP is rapidly reduced, and a WPP can rapidly suppress the overvoltage at a fault clearance because the reactive current reference is reduced. Using an electromagnetic transients program–released version (EMTP–RV) simulator, the performance of the proposed scheme was validated for a model system comprising 20 units of a 5-MW DFIG considering various scenarios, such as fault and wind conditions. Test results show that the proposed scheme enables a WPP to suppress the overvoltage at the POI and DFIG terminal within a short time under grid fault conditions

Development of 6 U CubeSat’s Deployable Solar Panel with Burn Wire Triggering Holding and Release Mechanism

In the present work, a deployable solar panel based on a burn wire triggering holding and release mechanism was developed for use of 6 U CubeSat. The holding and release mechanism was designed based on a nichrome burn wire cutting method widely used for CubeSat applications. However, it provides a high loading capability, reliable wire cutting, multiplane constraints, and handling simplicity during the tightening process of wire. A demonstration model of a printed circuit board-based solar panel stiffened by a high-pressure fiberglass-laminated G10 material was fabricated and tested to validate the effectiveness of the design and functionality of the mechanism under various test conditions. The structural safety of the solar panel combined with the mechanism in a launch vibration environment was verified through sine and random vibration tests at qualification level

Synthesis of Rare-Earth-Doped Strontium Tungstate Phosphor at Room Temperature and Applied Flexible Composite

In this study, we successfully synthesized rare-earth-doped crystalline SrWO4 at room temperature by co-precipitation. The results from the X-ray diffraction analysis showed a main diffraction peak related to the (112) plane. Phosphors doped with either Dy3+ or Sm3+ ions showed strong light absorption in the UV region and blue-yellow and red light emission. To synthesize a white light phosphor, Dy3+ and Sm3+ ions were co-doped to produce a SrWO4:[Sm3+]/[Dy3+] phosphor. When the Sm3+ ion concentration was increased and the Dy3+ concentration was maintained, the red light intensity increased while the blue-yellow light intensity decreased. The composites were combined with polydimethylsiloxane (PDMS), and a flexible composite material was fabricated. The composite exhibited various luminescence properties under UV and visible light, which suggested its potential for use as an LED color filter

Characteristics of 3D Printed Plastic Scintillator

Digital Light Processing (DLP) 3D printing technique can be a powerful tool to fabricate plastic scintillator with a geometrically desired shape in innovatively fast time. Plastic scintillator with the size of 30 mm × 30 mm × 10 mm was fabricated by using the plastic resin and the DLP 3D printer (ASIGA, Pico2HD). The characteristics of decay time, energy resolution, intrinsic detection efficiency were analyzed and compared between the fabricated 3D printing plastic scintillator and a commercial plastic scintillator BC408 (Saint-Gobain Crystal). Decay time profile of the tested plastic scintillators was measured for 137Cs Compton maximum electron 477 keV by using a modified time correlated single photon counting (TCSPC) setup. The time profile was fitted by reconvolution function, and each decay time component and contribution was analyzed. For energy resolution of plastic scintillator, the Gaussian spectrum for 137Cs Compton maximum electron 477 keV was selectively measured by using the γ-γ coincidence experimental setup. As a result, it was confirmed that the 3D printing plastic scintillator showed average decay time 15.6 ns and energy resolution 15.4%. These characteristics demonstrates the feasibility of 3D printing plastic scintillator as a radiation detector