STEP HEIGHT EFFECTS ON LOWER LIMB BIOMECHANICS AND BODY CENTRE OF MASS MOTION DURING ELLIPTICAL EXERCISE

Elliptical exercise (EE) has been shown to be beneficial for the development and maintenance of cardiorespiratory fitness. Despite these benefits, the feet are constrained by pedals to follow an elliptical trajectory, with the possibility of producing disadvantageous joint loads, body instability and potential musculoskeletal overuse injuries (Lu et al., 2007). Proper selection of step height during EE may help reduce these disadvantageous joint loads and instability. The purpose of the study was to study the effects of step height on the lower limb biomechanics and associated body center of mass (COM) motion during EE

A Microcantilever-based Gas Flow Sensor for Flow Rate and Direction Detection

The purpose of this paper is to apply characteristics of residual stress that causes cantilever beams to bend for manufacturing a micro-structured gas flow sensor. This study uses a silicon wafer deposited silicon nitride layers, reassembled the gas flow sensor with four cantilever beams that perpendicular to each other and manufactured piezoresistive structure on each micro-cantilever by MEMS technologies, respectively. When the cantilever beams are formed after etching the silicon wafer, it bends up a little due to the released residual stress induced in the previous fabrication process. As air flows through the sensor upstream and downstream beam deformation was made, thus the airflow direction can be determined through comparing the resistance variation between different cantilever beams. The flow rate can also be measured by calculating the total resistance variations on the four cantilevers.Comment: Submitted on behalf of EDA Publishing Association (http://irevues.inist.fr/handle/2042/16838

EFFECTS OF STEP LENGTH ON THE BIOMECHANICS OF LOWER LIMBS DURING ELLIPTICAL EXERCISE

Elliptical exercise (EE) has been developed as a low-impact aerobic exercise modality with increased popularity in fitness training and clinical applications over the last decade. During EE, the feet are constrained by pedals to follow an elliptical trajectory, with the possibility of producing disadvantageous joint loads and potential musculoskeletal overuse injuries (Lu et al., 2007). Therefore, proper selection of step length during EE may be helpful for the reduction of these disadvantageous joint loads. The purpose of the study was to study the effects of three different step lengths on biomechanics of the lower limbs during EE

Magnetic oxide semiconductors

Magnetic oxide semiconductors, oxide semiconductors doped with transition metal elements, are one of the candidates for a high Curie temperature ferromagnetic semiconductor that is important to realize semiconductor spintronics at room temperature. We review in this paper recent progress of researches on various magnetic oxide semiconductors. The magnetization, magneto-optical effect, and magneto-transport such as anomalous Hall effect are examined from viewpoint of feasibility to evaluate the ferromagnetism. The ferromagnetism of Co-doped TiO2 and transition metal-doped ZnO is discussed.Comment: 26 pages, 5 tables, 6 figure

The BCS-like gap in superconductor SmFeAsO_0.85F_0.15

Since the discovery of superconductivity in the cuprates two decades ago, it has been firmly established that the CuO_2 plane is consequential for high T_C superconductivity and a host of other very unusual properties. A new family of superconductors with the general composition of LaFeAsO_(1-x)F_x has recently been discovered but with the conspicuous lacking of the CuO_2 planes, thus raising the tantalizing questions of the different pairing mechanisms in these oxypnictide superconductors. Intimately related to pairing in a superconductor are the superconducting gap, its value, structure, and temperature dependence. Here we report the observation of a single gap in the superconductor SmFeAsO_0.85F_0.15 with T_C = 42 K as measured by Andreev spectroscopy. The gap value of 2Delta = 13.34+/-0.3 meV gives 2Delta/k_BT_C = 3.68, close to the BCS prediction of 3.53. The gap decreases with temperature and vanishes at T_C in a manner consistent with the Bardeen-Cooper-Schrieffer (BCS) prediction but dramatically different from that of the pseudogap behavior in the cuprate superconductors. Our results clearly indicate a nodeless gap order parameter, which is nearly isotropic in size across different sections of the Fermi surface, and are not compatible with models involving antiferromagnetic fluctuations, strong correlations, t-J model, and the like, originally designed for cuprates.Comment: 8 pages, 3 figure

Zn-doping effect on the magnetotransport properties of Bi_{2}Sr_{2-x}La_{x}CuO_{6+\delta} single crystals

We report the magnetotransport properties of Bi_{2}Sr_{2-x}La_{x}Cu_{1-z}Zn_{z}O_{6+\delta} (Zn-doped BSLCO) single crystals with z of up to 2.2%. Besides the typical Zn-doping effects on the in-plane resistivity and the Hall angle, we demonstrate that the nature of the low-temperature normal state in the Zn-doped samples is significantly altered from that in the pristine samples under high magnetic fields. In particular, we observe nearly-isotropic negative magnetoresistance as well as an increase in the Hall coefficient at very low temperatures in non-superconducting Zn-doped samples, which we propose to be caused by the Kondo scattering from the local moments induced by Zn impurities.Comment: 4 pages, 4 figures, final version (one reference added), published in Phys. Rev.

Generating scalable graph states in an atom-nanophotonic interface

Scalable graph states are essential for measurement-based quantum computation and many entanglement-assisted applications in quantum technologies. Generation of these multipartite entangled states requires a controllable and efficient quantum device with delicate design of generation protocol. Here we propose to prepare high-fidelity and scalable graph states in one and two dimensions, which can be tailored in an atom-nanophotonic cavity via state carving technique. We propose a systematic protocol to carve out unwanted state components, which facilitates scalable graph states generations via adiabatic transport of a definite number of atoms in optical tweezers. An analysis of state fidelity is also presented, and the state preparation probability can be optimized via multiqubit state carvings and sequential single-photon probes. Our results showcase the capability of an atom-nanophotonic interface for creating graph states and pave the way toward novel problem-specific applications using scalable high-dimensional graph states with stationary qubits.Comment: 5 figures with supplemental materia