Extreme call amplitude from near-field acoustic wave coupling in the stridulating water insect Micronecta scholtzi (Micronectinae)

Underwater acoustic transducers, particularly at low frequencies, are beset by problems of scale and inefficiency due to the large wavelengths of sound in water. In insect mating calls, a high call volume is usually desirable, increasing the range of signal transmission and providing a form of advertisement of the signaller's quality to a potential mate; however, the strength of the call is constrained by body size and by the need to avoid predators who may be listening in. Male crickets and water boatmen avoid some of the limitations of body size by exploiting resonant structures, which produce sharply tuned species specific songs, but call frequency and volume remain linked to body size. Recently, the water boatman Micronecta scholtzi was found to circumvent this rule, producing a louder mating call than that of similar, but much larger, Corixa. The resonant structure in Corixidae and Micronectinae is believed to be the trapped air reserves around the insect as it dives, driven by a stridulatory apparatus. However, the method by which energy is transferred from the striated area to the bubble is unknown. Here, we present modelling of a system of near-field coupling of acoustic sources to bubbles showing an exponential increase in sound power gain with decreasing distance that provides a simple solution to the stimulus of the air bubbles in Corixidae and Micronectinae and explains the discrepancy of M. scholtzi's extreme call volume. The findings suggest a possible route to engineered systems using near-field coupling to overcome size constraints in low-frequency (less than 500 Hz) underwater transducers, where the input efficiency of a piezoelectric device can be coupled through the hydrodynamic field to the high radiative efficiency of a near-ideal monopole emitter

Housing influence on multi-band directional MEMS microphones inspired by Ormia ochracea

A new bio-inspired multi-band directional MEMS microphone based on the hearing properties of the fly Ormia ochracea is presented, together with the behavioral influence of 3D-printed housings. The multi-user foundry fabricated microphone operates on four frequency bands, all below 10 kHz and acts as a pressure gradient directional microphone with figure of eight polar pattern, or as an omni-directional microphone depending on the housing. The influence of an open or closed backside housing on the frequency response and directionality is shown, leading to the loss of directionality with no acoustic access to the backside of the fly-ear inspired microphone membrane

Additive manufacturing (AM) capacitive acoustic and ultrasonic transducers using a commercial direct light processing (DLP) printer

In recent years, there has been increasing interest in using additive manufacturing (3D printing) technology to fabricate sensors and actuators due to rapid prototyping, low-cost manufacturing processes, customized features and the ability to create complex geometries at micrometre scale. State of the art additive manufactured acoustic and ultrasonic transducers show limitations in miniaturization, repeatability (defects) and sensitivity. This new work encompasses the development of a capacitive acoustic and ultrasonic transducer, including its fabrication process using a commercial digital light processing printer and output signal characterization with a custom-made amplification circuit. A set of capacitive acoustic and ultrasonic transducers was fabricated and tested using different diaphragm diameters from 1.8 -2.2mm, for comparison, with central operating frequency between 19 -54 kHz, respectively. This capacitive transducer design has a receiving sensitivity of up to 0.4 mV/Pα at its resonant frequency, and a comparison with a commercial reference microphone is provided

Material stiffness variation in mosquito antennae

The antennae of mosquitoes are model systems for acoustic sensation, in that they obey general principles for sound detection, using both active feedback mechanisms and passive structural adaptations. However, the biomechanical aspect of the antennal structure is much less understood than the mechano-electrical transduction. Using confocal laser scanning microscopy, we measured the fluorescent properties of the antennae of two species of mosquito – Toxorhynchites brevipalpis and Anopheles arabiensis – and, noting that fluorescence is correlated with material stiffness, we found that the structure of the antenna is not a simple beam of homogeneous material, but is in fact a rather more complex structure with spatially distributed discrete changes in material properties. These present as bands or rings of different material in each subunit of the antenna, which repeat along its length. While these structures may simply be required for structural robustness of the antennae, we found that in FEM simulation, these banded structures can strongly affect the resonant frequencies of cantilever-beam systems, and therefore taken together our results suggest that modulating the material properties along the length of the antenna could constitute an additional mechanism for resonant tuning in these species

Fabrication and characterization of a novel photoactive based (0-3) piezocomposite material with potential as a functional material for additive manufacturing of piezoelectric sensors

The development of 3D-printed sensors and actuators from piezocomposite materials has increased in recent years due to the ease of production, low-cost and improved functionality additive manufacturing provides. The piezocomposite material developed in this work has the potential to be used as a functional material in stereolithographic additive manufacturing by combining the optical, viscoelastic properties of NOA 65 and the piezoelectric properties of Barium Titanate. The new (0-3) piezocomposite material consists of Norland Optical Adhesive 65 (NOA 65) as the polymer matrix and Barium Titanate (BaTiO3) with particles sizes (100 nm, 200 nm and 500 nm) as the dielectric filler. We synthesized thin film samples of the (0-3) piezocomposite with 60% w/w BaTiO3 using solution mixing and spin coating method to produce samples with layer thickness of 100 μm. Fourier-transform infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM) techniques were used to analyze the microstructure of the piezocomposite to determine the effect of different particles sizes of BaTiO3 on the structural and mechanical properties of the composite. The longitudinal piezoelectric coefficient d33 was also measured using the laser vibrometer technique. Both single point scans and full surface scans were carried out to obtain the average piezoelectric coefficient d33 of the composite material. The results of the SEM confirmed the (0-3) structure of the piezocomposite material with isolated BaTiO3 nanoparticles. It further showed the uniform distribution of the BaTiO3 nanoparticles across each of the samples. FTIR analysis showed that the filler nanoparticles had no effect on the native structure of the polymer matrix. The longitudinal piezoelectric coefficient d33 of the piezocomposite material was observed to increase with increasing BaTiO3 particle sizes, while the indentation modulus of the composite investigated using the method of Oliver and Pharr was observed to decrease with an increase in particle size. Results from the single point scans showed the composite with BaTiO3 particle size 100 nm, 200 nm and 500 nm having an average d33 of 2.1 pm/V, 3.0 pm/V and 3.9 pm/V while the average d33 obtained from the full surface scan of 1430 scan points showed 1.4 pm/V, 6.1 pm/V, 7.2 pm/V

Engineered surfaces that promote capture of latent proteins to facilitate integrin-mediated mechanical activation of growth factors

Conventional osteogenic platforms utilize active growth factors to repair bone defects that are extensive in size, but they can adversely affect patient health. Here, an unconventional osteogenic platform is reported that functions by promoting capture of inactive osteogenic growth factor molecules to the site of cell growth for subsequent integrin-mediated activation, using a recombinant fragment of latent transforming growth factor beta-binding protein-1 (rLTBP1). It is shown that rLTBP1 binds to the growth-factor- and integrin-binding domains of fibronectin on poly(ethyl acrylate) surfaces, which immobilizes rLTBP1 and promotes the binding of latency associated peptide (LAP), within which inactive transforming growth factor beta 1 (TGF-β1) is bound. rLTBP1 facilitates the interaction of LAP with integrin β1 and the subsequent mechanically driven release of TGF-β1 to stimulate canonical TGF-β1 signaling, activating osteogenic marker expression in vitro and complete regeneration of a critical-sized bone defect in vivo

Shrinking wings for ultrasonic pitch production: hyperintense ultra-short-wavelength calls in a new genus of neotropical katydids (Orthoptera: tettigoniidae)

This article reports the discovery of a new genus and three species of predaceous katydid (Insecta: Orthoptera) from Colombia and Ecuador in which males produce the highest frequency ultrasonic calling songs so far recorded from an arthropod. Male katydids sing by rubbing their wings together to attract distant females. Their song frequencies usually range from audio (5 kHz) to low ultrasonic (30 kHz). However, males of Supersonus spp. call females at 115 kHz, 125 kHz, and 150 kHz. Exceeding the human hearing range (50 Hz–20 kHz) by an order of magnitude, these insects also emit their ultrasound at unusually elevated sound pressure levels (SPL). In all three species these calls exceed 110 dB SPL rms re 20 µPa (at 15 cm). Males of Supersonus spp. have unusually reduced forewings (<0.5 mm2). Only the right wing radiates appreciable sound, the left bears the file and does not show a particular resonance. In contrast to most katydids, males of Supersonus spp. position and move their wings during sound production so that the concave aspect of the right wing, underlain by the insect dorsum, forms a contained cavity with sharp resonance. The observed high SPL at extreme carrier frequencies can be explained by wing anatomy, a resonant cavity with a membrane, and cuticle deformation

So Small, So Loud: Extremely High Sound Pressure Level from a Pygmy Aquatic Insect (Corixidae, Micronectinae)

To communicate at long range, animals have to produce intense but intelligible signals. This task might be difficult to achieve due to mechanical constraints, in particular relating to body size. Whilst the acoustic behaviour of large marine and terrestrial animals has been thoroughly studied, very little is known about the sound produced by small arthropods living in freshwater habitats. Here we analyse for the first time the calling song produced by the male of a small insect, the water boatman Micronecta scholtzi. The song is made of three distinct parts differing in their temporal and amplitude parameters, but not in their frequency content. Sound is produced at 78.9 (63.6–82.2) SPL rms re 2.10−5 Pa with a peak at 99.2 (85.7–104.6) SPL re 2.10−5 Pa estimated at a distance of one metre. This energy output is significant considering the small size of the insect. When scaled to body length and compared to 227 other acoustic species, the acoustic energy produced by M. scholtzi appears as an extreme value, outperforming marine and terrestrial mammal vocalisations. Such an extreme display may be interpreted as an exaggerated secondary sexual trait resulting from a runaway sexual selection without predation pressure

Volcanic ash as a resource for future research on Earth and the Moon

When a volcano erupts, it is often associated with destruction, particularly damage to infrastructure and loss of life. But these natural events also offer unexpected research opportunities, leading to serendipitous discoveries. This was the case for the volcanic events that made the headlines during 19 September to 25 December 2021, on the Canarian Island of La Palma. Rather than viewing the voluminous ash that erupted as a waste material needing to be removed as soon as possible, we saw the many possibilities that this remarkable material could offer science and engineering. Sustainability is a word that is commonly used in connection with geology these days. Here we present some possibilities of how the La Palma ash can be re‐purposed for use on this planet but also help us to develop new ideas for the future living on the Moon

Developing and investigating a nanovibration intervention for the prevention/reversal of bone loss following spinal cord injury

Osteoporosis disrupts the fine-tuned balance between bone formation and resorption, leading to reductions in bone quantity and quality and ultimately increasing fracture risk. Prevention and treatment of osteoporotic fractures is essential for reductions in mortality, morbidity, and the economic burden, particularly considering the aging global population. Extreme bone loss that mimics time-accelerated osteoporosis develops in the paralyzed limbs following complete spinal cord injury (SCI). In vitro nanoscale vibration (1 kHz, 30 or 90 nm amplitude) has been shown to drive differentiation of mesenchymal stem cells toward osteoblast-like phenotypes, enhancing osteogenesis and inhibiting osteoclastogenesis simultaneously. Here, we develop and characterize a wearable device designed to deliver and monitor continuous nanoamplitude vibration to the hindlimb long bones of rats with complete SCI. We investigate whether a clinically feasible dose of nanovibration (two 2 h/day, 5 days/week for 6 weeks) is effective at reversing the established SCI-induced osteoporosis. Laser interferometry and finite element analysis confirmed transmission of nanovibration into the bone, and microcomputed tomography and serum bone formation and resorption markers assessed effectiveness. The intervention did not reverse SCI-induced osteoporosis. However, serum analysis indicated an elevated concentration of the bone formation marker procollagen type 1 N-terminal propeptide (P1NP) in rats receiving 40 nm amplitude nanovibration, suggesting increased synthesis of type 1 collagen, the major organic component of bone. Therefore, enhanced doses of nanovibrational stimulus may yet prove beneficial in attenuating/reversing osteoporosis, particularly in less severe forms of osteoporosis