Advances in Non-Contact Measurement of Creep Properties

As the required service temperatures for superalloys increases, so do the demands on testing for development of these alloys. Non-contact measurement of creep of refractory metals using electrostatic levitation has been demonstrated at temperatures up to 2300 C using samples of only 20-40 mg. These measurements load the spherical specimen by inertial forces due to rapid rotation. However, the first measurements relied on photon pressure to accelerate the samples to the high rotational rates of thousands of rotations per second, limiting the applicability to low stresses and high temperatures. Recent advances in this area extend this measurement to higher stresses and lower-temperatures through the use of an induction motor to drive the sample to such high rotational speeds. Preliminary results on new measurements on new materials will be presented

31st Annual Meeting and Associated Programs of the Society for Immunotherapy of Cancer (SITC 2016) : part two

Background The immunological escape of tumors represents one of the main ob- stacles to the treatment of malignancies. The blockade of PD-1 or CTLA-4 receptors represented a milestone in the history of immunotherapy. However, immune checkpoint inhibitors seem to be effective in specific cohorts of patients. It has been proposed that their efficacy relies on the presence of an immunological response. Thus, we hypothesized that disruption of the PD-L1/PD-1 axis would synergize with our oncolytic vaccine platform PeptiCRAd. Methods We used murine B16OVA in vivo tumor models and flow cytometry analysis to investigate the immunological background. Results First, we found that high-burden B16OVA tumors were refractory to combination immunotherapy. However, with a more aggressive schedule, tumors with a lower burden were more susceptible to the combination of PeptiCRAd and PD-L1 blockade. The therapy signifi- cantly increased the median survival of mice (Fig. 7). Interestingly, the reduced growth of contralaterally injected B16F10 cells sug- gested the presence of a long lasting immunological memory also against non-targeted antigens. Concerning the functional state of tumor infiltrating lymphocytes (TILs), we found that all the immune therapies would enhance the percentage of activated (PD-1pos TIM- 3neg) T lymphocytes and reduce the amount of exhausted (PD-1pos TIM-3pos) cells compared to placebo. As expected, we found that PeptiCRAd monotherapy could increase the number of antigen spe- cific CD8+ T cells compared to other treatments. However, only the combination with PD-L1 blockade could significantly increase the ra- tio between activated and exhausted pentamer positive cells (p= 0.0058), suggesting that by disrupting the PD-1/PD-L1 axis we could decrease the amount of dysfunctional antigen specific T cells. We ob- served that the anatomical location deeply influenced the state of CD4+ and CD8+ T lymphocytes. In fact, TIM-3 expression was in- creased by 2 fold on TILs compared to splenic and lymphoid T cells. In the CD8+ compartment, the expression of PD-1 on the surface seemed to be restricted to the tumor micro-environment, while CD4 + T cells had a high expression of PD-1 also in lymphoid organs. Interestingly, we found that the levels of PD-1 were significantly higher on CD8+ T cells than on CD4+ T cells into the tumor micro- environment (p < 0.0001). Conclusions In conclusion, we demonstrated that the efficacy of immune check- point inhibitors might be strongly enhanced by their combination with cancer vaccines. PeptiCRAd was able to increase the number of antigen-specific T cells and PD-L1 blockade prevented their exhaus- tion, resulting in long-lasting immunological memory and increased median survival

Extensional-flow-induced Crystallization of Polypropylene

A filament stretching extensional rheometer was used to investigate the effect of uniaxial flow on the crystallization of polypropylene. Samples were heated to a temperature above the melt temperature to erase their thermal and mechanical histories. The Janeschitz-Kriegl protocol was applied and samples were stretched at various extension rates to a final strain of e = 3.0. Differential scanning calorimetry was applied to crystallized samples to measure the degree of crystallinity. The results showed that a minimum extension rate, corresponding to a Weissenberg number of approximately Wi = 1, is required for an increase in percent crystallization to occur. Below this Weissenberg number, the flow is not strong enough to align the tubes of constrained polymer chains and as a result there is no change in the final percent crystallization. An extension rate was also found for which percent crystallization is maximized. The increase in crystallinity is likely due to flow-induced orientation and alignment of tubes of constrained polymer chains. Polarized-light microscopy verified an increase in number and decrease in size of spherulites with increasing extension rate. Small angle X-ray scattering showed a 7% decrease in inter-lamellar spacing at the transition to flow-induced increase in crystallization. Crystallization kinetics were examined by observing the time required for melts to crystallize under uniaxial flow. The crystallization time decreased with increasing extension rate, even for extension rates where no increase in percent crystallization was observed. These results demonstrate that the speed of crystallization kinetics is greatly enhanced by the application of extensional flow

Extensional-flow-induced Crystallization of Polypropylene

A filament stretching extensional rheometer was used to investigate the effect of uniaxial flow on the crystallization of polypropylene. Samples were heated to a temperature above the melt temperature to erase their thermal and mechanical histories. The Janeschitz-Kriegl protocol was applied and samples were stretched at various extension rates to a final strain of e = 3.0. Differential scanning calorimetry was applied to crystallized samples to measure the degree of crystallinity. The results showed that a minimum extension rate, corresponding to a Weissenberg number of approximately Wi = 1, is required for an increase in percent crystallization to occur. Below this Weissenberg number, the flow is not strong enough to align the tubes of constrained polymer chains and as a result there is no change in the final percent crystallization. An extension rate was also found for which percent crystallization is maximized. The increase in crystallinity is likely due to flow-induced orientation and alignment of tubes of constrained polymer chains. Polarized-light microscopy verified an increase in number and decrease in size of spherulites with increasing extension rate. Small angle X-ray scattering showed a 7% decrease in inter-lamellar spacing at the transition to flow-induced increase in crystallization. Crystallization kinetics were examined by observing the time required for melts to crystallize under uniaxial flow. The crystallization time decreased with increasing extension rate, even for extension rates where no increase in percent crystallization was observed. These results demonstrate that the speed of crystallization kinetics is greatly enhanced by the application of extensional flow.Master of Science (M.S.