Odabrana kemijska i fizička svojstva drvne sječke od borovine inokulirane plijesnima Aspergillus i Penicillium

Mold fungi representing genera of Penicillium and Aspergillus commonly develop on the surface of freshly harvested wood chips during storage. As a result, they are often considered as low-quality material and intended for incineration. Thus, the aim of the present study was to investigate the effect of wood chips infestation with mold fungi representing genera of Aspergillus and Penicillium on their basic chemical and physical properties, such as: chemical structure (evaluated with FTIR spectroscopy), mass loss and hygroscopicity, after an incubation of 3, 6 and 9 weeks. Based on the visual assessment and ergosterol content analysis, it was found that inoculation of wood chips with molds led to the intense fungal development on their surface. However, as observed in FTIR spectra, the presence of molds caused no changes in wood chemical structure. Furthermore, no mass loss and no significant increase in the hygroscopicity of wood were observed. Therefore, pine wood chips overgrown by studied genera of fungi seem to be a valuable material for various applications.Plijesni rodova Aspergillus i Penicillium najčešće se razvijaju na površini svježe pripremljene drvne sječke tijekom skladištenja, zbog čega se takva sječka često smatra nekvalitetnim materijalom i spaljuje se. Stoga je cilj ovoga istraživanja bio istražiti utjecaj zaraženosti drvne sječke plijesnima rodova Aspergillus i Penicillium na njezina osnovna kemijska i fizička svojstva kao što su kemijska struktura (ispitano FTIR spektroskopijom), gubitak mase i higroskopnost nakon ikubacije od tri, šest i devet tjedana. Na temelju vizualne procjene i analize sadržaja ergosterola, utvrđeno je ddrvne sječke. Međutim, na FTIR spektrima je uočeno da plijesni nisu uzrokovale promjene u kemijskoj strukturi drva. Nadalje, nije uočen gubitak mase niti znatno povećanje higroskopnosti drva. Stoga se može zaključiti da je drvna sječka od borovine zaražena promatranim rodovima plijesni upotrebljiv materijal za različite primjenea je inokulacija drvne sječke plijesnima prouzročila intenzivan razvoj plijesni na površin

Diagnosis of tuberculous lymphadenitis based on the fineneedleaspirationsamplesanalysis

Tuberculous lymphadenitis is one of the most common extrapulmonary manifestations of tuberculosis. The most common lymph nodes involved are in the cervical region. Lymphadenitis due to M. tuberculosis generally presents with enlarging neck lymph nodes over weeks or months associated with fever, weight loss and fatigue. Fine needle aspiration (FNA) of affected lymph nodes has been shown to yield a high sensitivity and specificityinthe diagnosis of tuberculous lymphadenitis. Specimens should be examined cytologically, as well as by AFB smear and cultures. The time between the onset of symptoms, clinical presentation and final diagnosis is often too long.We present a case of 60 years old man with tuberculous lymphadenitis, initially suspected of lymphoproliferative disease

Filaggrin Gene Defects Are Independent Risk Factors for Atopic Asthma in a Polish Population: A Study in ECAP Cohort

BACKGROUND: FLG null variants of which 2282del4 and R501X are the most frequent in Caucasians are established risk factors for atopic dermatitis (AD) with an effect probably mediated through impairment of epidermal barrier. Among subjects with AD FLG defects are also consistently associated with asthma and allergic rhinitis (AR) but it is less clear to what extent these associations are also present independently from skin disease. The aim of the present study was to evaluate the role of 2282del4 and R501X in predisposing to these allergic phenotypes in a Polish population. METHODOLOGY: 2282del4 and R501X were typed among 3,802 participants of the Epidemiology of Allergic Diseases in Poland (ECAP) survey, a cross-sectional population-based study using ECRHS II and ISAAC questionnaires, and ambulatory examination. PRINCIPAL FINDINGS: The FLG null variants were associated with AD (OR = 2.01, CI: 1.20-3.36, P = 0.007), allergic rhinitis (in particular persistent form, OR = 1.69, CI:1.12-2.54, P = 0.011), and asthma (in particular atopic asthma, OR = 2.22, CI:1.24-3.96, P = 0.006). Association with atopic asthma (but not persistent allergic rhinitis) was also present in the absence of AD, (OR = 2.02, CI: 1.07-3.81, P = 0.027) as well as in the absence of AD and history of broadly defined inflammatory skin disease (OR = 2.30, CI: 1.07-4.93, P = 0.03). Association to atopic asthma would have not been found if diagnosis was made by questionnaire only (OR = 1.15, CI: 0.58-2.32, P = 0.8). We did not observe an association between FLG variants and allergic sensitizations (P = 0.8) or total IgE. (P = 0.6). CONCLUSIONS/SIGNIFICANCE: In a Polish population FLG 2282del4 and R501X carriage increases risk for development of AD and atopic asthma (also in the absence of AD or history thereof). This suggests that interventions aimed at restoring epidermal barrier may have a general role in asthma prophylaxis/treatment

Aktywność rybocyklibu i hormonoterapii u chorych na zaawansowanego, luminalnego HER2-ujemnego raka piersi w praktyce klinicznej — opisy przypadków

Selektywne inhibitory kinaz zależnych od cyklin CDK4 i CDK 6 (iCDK4/6, cyclin-dependent kinase inhibitors) — palbocyklib, rybocyklib i abemacyklib — stanowią nową grupę leków zmniejszających proliferację przez zahamowanie przejścia komórek w cyklu komórkowym z fazy G1 do S. Leki te są obecnie standardem postępowania u chorych na miejscowo zaawansowanego lub uogólnionego raka piersi z ekspresją receptorów estrogenowych (ER, estrogen receptor) i progesteronowych (PR, progesterone receptor) bez nadekspresji receptora naskórkowego czynnika wzrostu typu 2 (HER2, human epidermal growth factor receptor type 2) w skojarzeniu z jednym z inhibitorów aromatazy lub fulwestrantem w pierwszej linii leczenia lub po niepowodzeniu wcześniejszej hormonoterapii. W niniejszym opracowaniu przedstawiono opisy przypadków chorych na raka piersi leczonych rybocyklibem w skojarzeniu z hormonoterapią w ramach programu rozszerzonego dostępu (MAP, managed access program)

Properties of Rigid Polyurethane Foam Filled with Sawdust from Primary Wood Processing

In this study, the possibility of using sawdust, a by-product of primary wood processing, as a filler (WF) for rigid polyurethane (PUR) foams was investigated. The effects of the addition of 5, 10, 15 and 20% of WF particles to the polyurethane matrix on the foaming process, cell structure and selected physical-mechanical properties such as density, thermal conductivity, dimensional stability, water absorption, brittleness, compressive and bending strengths were evaluated. Based on the results, it was found that the addition of WF in the amount of up to 10% does not significantly affect the kinetics of the foam foaming process, allowing the reduction of their thermal conductivity, significantly reducing brittleness and maintaining high dimensional stability. On the other hand, such an amount of WF causes a slight decrease in the compressive strength of the foam, a decrease in its bending strength and an increase in water absorption. However, it is important that in spite of the observed decrease in the values of these parameters, the obtained results are satisfactory and consistent with the parameters of insulation materials based on rigid PUR foam, currently available on the market

Morphological Features of PUR-Wood Particle Composite Foams

The aim of this study was to apply waste wood particles (WP) with different sizes from primary wood processing as a filler for open-cell PUR foams. For this purpose, various wood particle sizes were added as a filler for polyurethane foams (PUR). The effects of the addition of of 0.05–1.25–2.0 of WP to the polyurethane matrix on the density, the kinetics of PUR foaming, the cell structure, and the morphology were investigated. Scanning electron microscope (SEM) and X-ray computer tomography were used. Based on the results, it was found that the addition of WP in the amount of 10% leads to an increase in density with an increase in particle size. The research shows that the morphology of the PUR-WP foam is influenced by its particle size. The difference in the number and size of cells in PUR-WP composites depends on the wood particle size. The addition of dust causes the formation of cells of much smaller sizes; confirmed by SEM images. Moreover, computer tomography clearly demonstrates that the WP are well-dispersed within the foams’ structures

The Possibility to Use Pine Timber Pieces with Small Size in the Production of Glulam Beams

Engineered wood products, such as glulam beams, attract much attention from the building industry in recent years. Therefore, there is a constant necessity to seek new models of structural beams, which assume the use of outsized sawn wood pieces as an alternative for the standard construction timber. Three variants of glulam beams, composed of the main yield and side boards arranged in various structures, were proposed. Moreover, the usefulness of wedge-jointed, small-sized timber pieces was also investigated. The manufactured beams were tested, in terms of their mechanical properties, such as bending strength, elastic energy, modulus of elasticity, and resilience. The outcomes have shown that the beams manufactured using wedge-bonded timber of lower grade do not deviate considerably from beams produced from homogeneous lamellas. Furthermore, the results of modulus of elasticity, in the case of the three-layered beams composed of both small-sized non-homogenous main yield and side boards, exceeded the requirements from EN 14080. It allowed us to classify the obtained materials as GL 32c, which is the highest grade specified within the standard

The Effect of the Tree Dieback Process on the Mechanical Properties of Pine (Pinus sylvestris L.) Wood

As a result of the progressing climate changes, there is an increase in the volume of pine deadwood harvested each year from Polish forests. Its presence is an important part of the forest ecosystem; however, there are some indications that the material obtained from dying trees can be characterized by lower quality and properties. Taking into account the growing issue of tree dieback, the volume of pine wood annually harvested in Poland, and the importance of wooden products from an economic standpoint, preliminary research aimed at recognizing the process and its effect on the mechanical properties was conducted. Model trees in Brzeg Forest District were selected based on the crown defoliation. The properties of wood obtained from trees representing three different categories of soundness were determined according to the relevant standards. Based on the results of density, modulus of elasticity, bending strength, and compressive strength, it was found that there were statistically significant differences in wood quality depending on the condition of the tree. The results were particularly interesting in the case of compressing strength, where a healthy tree of lower density showed a similar strength to a dying tree with a much higher density

The Application of Various Bark Species as a Fillers for UF Resin in Plywood Manufacturing

The aim of the presented study was to apply various bark species (birch, beech, maple, pine and spruce) as fillers for urea-formaldehyde (UF) resin in three-layer plywood manufacturing. For this purpose, all types of bark were ground and added to the adhesive mixture. The resultant plywood was subjected to investigations of the following: tensile strength, modulus of elasticity (MOE), bending strength (MOR) and formaldehyde emission. The results indicate a reduction in the tensile strength. Moreover, the lack of significant improvement in strength parameters can be explained by too high a load of the filler (20 wt%). In the case of formaldehyde emissions, a reduction was observed for birch (B-1), beech (B-2), maple (B-3) and pine bark (B-4). In addition, an increase in the emission of formaldehyde was recorded only for spruce bark

The Possibility of Using Pine Bark Particles in the Chipboard Manufacturing Process

This research evaluated the possibility of using sawmill by-products from the roundwood-processing line in the production of wood-based panels. Due to its number of favorable properties, interesting chemical composition and large reserves resulting from the lack of industrial applications, the research focused particularly on the use of bark. Manufactured variants of boards differed in the proportions of wood chips to bark (70:30, 60:40, 50:50). Moreover, the boards containing only wood chips and a mixture of chips and sawdust were used as references. Urea-formaldehyde adhesive mixed with ammonium nitrate as a hardener was applied as a binding agent for the boards. Based on the mechanical properties (modulus of elasticity, modulus of rupture, internal bonding), physical properties (density, thickness swelling, water absorption) and content and emission of formaldehyde, it was found that it is possible to produce boards characterized by good properties from sawmill by-products without advanced processing. Moreover, the use of bark instead of sawdust in order to increase the homogeneity of the cross-section allows one to obtain panels with significantly lower formaldehyde emission and water uptake