Transport of small anionic and neutral solutes through chitosan membranes: Dependence on cross-linking and chelation of divalent cations

Chitosan membranes were prepared by solvent casting and cross-linked with glutaraldehyde at several ratios under homogeneous conditions. The cross-linking degree, varying from 0 to 20%, is defined as the ratio between the total aldehyde groups and the amine groups of chitosan. Permeability experiments were conducted using a side-by-side diffusion cell to determine the flux of small molecules of similar size but with different chemical moieties, either ionized (benzoic acid, salicylic acid, and phthalic acid) or neutral (2-phenylethanol) at physiological pH. The permeability of the different model molecules revealed to be dependent on the affinity of those structurally similar molecules to chitosan. The permeability of the salicylate anion was significantly enhanced by the presence of metal cations commonly present in biological fluids, such as calcium and magnesium, but remained unchanged for the neutral 2-phenylethanol. This effect could be explained by the chelation of metal cations on the amine groups of chitosan, which increased the partition coefficient. The cross-linking degree was also correlated with the permeability and partition coefficient. The change in the permeation properties of chitosan to anionic solutes in the presence of these metallic cations is an important result and should be taken into consideration when trying to make in vitro predictions of the drug release from chitosan-based controlled release systems

Kitozanski umetci za periodontitis: Utjecaj količine lijeka, plastifikatora i umrežavanja na oslobađanje metronidazola in vitro

Chitosan based metronidazole (MZ) inserts were fabricated by the casting method and characterized with respect to mass and thickness uniformity, metronidazole loading and in vitro metronidazole release kinetics. The fabricated inserts exhibited satisfactory physical characteristics. The mass of inserts was in the range of 5.63 ± 0.42 to 6.04 ± 0.89 mg. The thickness ranged from 0.46 ± 0.06 to 0.49 ± 0.08 mm. Metronidazole loading was in the range of 0.98 ± 0.09 to 1.07 ± 0.07 mg except for batch CM3 with MZ loading of 2.01 ± 0.08 mg. The inserts exhibited an initial burst release at the end of 24 h, irrespective of the drug to polymer ratio, plasticizer content or cross-linking. However, further drug release was sustained over the next 6 days. Cross-linking with 10% (m/m) of glutaraldehyde inhibited the burst release by ~30% and increased the mean dissolution time (MDT) from 0.67 to 8.59 days. The decrease in drug release was a result of reduced permeability of chitosan due to cross-linking.Umetci metronidazola na bazi kitozana napravljeni su kasting metodom. Proučavana je ujednačenost mase i debljine, količina ljekovite tvari i kinetika oslobađanja metronidazola in vitro. Fizičke karakteristike umetaka bile su zadovoljavajuće: masa je bila u rasponu 5,63 ± 0,42 – 6,04 ± 0,89 mg, debljina od 0.46 ± 0.06 – 0.49 ± 0.08 mm with, količina metronidazola od 0,98 ± 0,09 – 1,07 ± 0,07 mg. Nakon 24 h iz svih umetaka, neovisno o omjeru ljekovite tvari i polimera, količini plastifikatora ili umrežavanju, dio metronidazola se naglo oslobodio. Međutim, daljnje oslobađanje je bilo polagano tijekom 6 dana. Umrežavanje s 10% (m/m) otopinom glutaraldehida spriječilo je naglo oslobađanje za ~30% i povećalo je srednje vrijeme oslobađanja (MDT) s 0,67 na 8,59 dana. Smanjenje u oslobađanju ljekovite tvari posljedica je smanjenja permeabilnosti umreženog kitozana

The Sorption of Ketotifen Fumarate by Chitosan

The purpose of this investigation was to determine the mechanism of interaction between ketotifen fumarate and chitosan at different pH values. The specific surface area of chitosan was determined using gas sorption analyzer. The sorption experiments were conducted at pH 7 and 10 using two different particle size ranges of chitosan. The solutions were prepared at constant ionic strength and buffer concentration, with only varying the pH. The rotating bottle method was used for measuring the sorption. The average specific surface areas for the two different particle size ranges of chitosan were found to be 4.56 and 0.74 m2/g. The Langmuir-like equation and a model independent equation were both applied to the sorption experimental data. The extent of ketotifen uptake at pH 7 for small and large particles of chitosan was found to be 1,073 and 2,204 mg/g respectively. While the extent of ketotifen uptake at pH 10 for small and large particles of chitosan was found to be 4 and 11 mg/g respectively. The aforementioned results indicated that sorption of ketotifen fumarate at pH 7 is extremely high compared to pH 10 and that the sorption increases by decreasing the specific surface area of chitosan. Based on the results obtained, the following conclusions were reached. Ketotifen might be absorbed into the bulk structure of chitosan in addition to being adsorbed on the surface and the ability of chitosan to swell at pH 7 has a significant role in increasing its uptake

Development and in vitro evaluation of chitosan-Eudragit RS 30D composite wound dressings

The purpose of this research was to design and evaluate chitosan-based films intended for wound dressing application. Required properties for successful wound dressing, such as liquid uptake, vapor and oxygen penetration, bioadhesiveness, and film elasticity, were examined. Water uptake and vapor penetration of the films were determined gravimetrically, while oxygen penetration was determined by Winkler’s method. The bioadhesive properties were determined with an in-house pulley system instrument using a pig gut model. Film elasticity was determined with a stretch test using an Instron apparatus. The results showed that pure chitosan films exhibited relatively high liquid uptake and the adsorption tended to decrease with the addition of Eudragit RS 30D. Moisture vapor and oxygen were found to be able to penetrate through all film formulations in comparable amounts. The bioadhesiveness test tended to show lower bioadhesive properties with the addition of Eudragit RS 30D. The formulation containing only chitosan exhibited low elongation of the film at 2 N, but the film elasticity increased with the addition of Eudragit RS 30D. In conclusion, the addition of Eudragit RS 30D could improve a film’s mechanical properties but lower its bioadhesiveness