Способы функционализации титановых имплантатов наночастицами серебра

Работа посвящена поиску оптимального метода функционализации металлическихтитановых подложек наночастицами серебра для формирования антибактериального интерфейса на поверхности экспериментальных образцов

Influence of Anodization Time and Voltage on the Parameters of TiO[2] Nanotubes

A vertically aligned titania nanotube layer was obtained by electrochemical anodic oxidation in the electrolyte contained 0.4 wt% solution of NH[4]F in 54 ml of ethylene glycol and 5 ml of deionized water, after titanium was chemically cleaned/etched with a mixture of HCl, H[2]O and HNO[3] solution for removing the natural oxide films. The morphology and composition of the titania nanotube layer were examined by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The anodization of TiO[2] nanotubes was done using 60 V for 240 min and 30 min, and 30 V for 30 min. The diameter of the titania nanotubes was about 52-156 nm, the wall thickness about 32-53 nm and the height about 0.9-6.3 [mu]m. The pore size of TiO[2] nanotubes influences the dissolution rate of CaP thin films and Young's modulus, which is significantly lower than that of the Ti substrate. Our future challenge will be investigation of the microstructure and mechanical behavior of titania nanotubes with CaP film

Effect of the SR-containing hydroxyapatite nanoparticles doping on the polymer fiber morphology within the 3-D artificial scaffolds for bone tissue regeneration

Functionalized 3-D scaffolds based on polycaprolactone (PCL) with strontium-containing hydroxyapatite (Sr-HA) were prepared via electrospinning technique. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) were used to investigate the structure and morphology of the scaffolds. The experimental results revealed that due to incorporation of Sr-HA particles into the polymer fibers, the surface of PCL/Sr-HA hybrid 3-D polymer scaffolds possessed porous and rough structure, which potentially should provide stimulation of adhesion and growth of bone cells

Synthesis of positively and negatively charged silver nanoparticles and their deposition on the surface of titanium

Bacterial infections related to dental implants are currently a significant complication. A good way to overcome this challenge is functionalization of implant surface with Ag nanoparticles (NPs) as antibacterial agent. This article aims at review the synthesis routes, size and electrical properties of AgNPs. Polyvinyl pyrrolidone (PVP) and polyethyleneimine (PEI) were used as stabilizers. Dynamic Light Scattering, Nanoparticle Tracking Analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDX) have been used to characterize the prepared AgNPs. Two types of NPs were synthesized in aqueous solutions: PVP-stabilized NPs with a diameter of the metallic core of 70 ± 20 nm, and negative charge of -20 mV, PEI-stabilized NPs with the size of the metallic core of 50 ± 20 nm and positive charge of +55 mV. According to SEM results, all the NPs have a spherical shape. Functionalization of the titanium substrate surface with PVP and PEI-stabilized AgNPs was carried out by dropping method. XRD patterns revealed that the AgNPs are crystalline with the crystallite size of 14 nm

Surface functionalization of titanium with silver nanoparticles

This study aims to investigate the most efficient ways for metallic samples functionalization with silver nanoparticles (AgNPs). Three different techniques of surface functionalization have been used for the coating of titanium metal, i.e. the sessile drop method (evaporation), dip-coating and electrophoretic deposition (EPD). AgNPs stabilized with polyvinylpyrrolidone had a spherical shape and the metallic core diameter, charge and polydispersity index were 70±20 nm, -15 mV and 0.192, respectively. SEM analysis revealed that AgNPs were homogeneously distributed over the entire surface and did not form the particle agglomerates only in case of EPD. Thus, EPD method and spherical AgNPs can be used for further investigation concerning the preparation of biocomposites with antibacterial and bioactive properties

Formation and Characterization of Crystalline Hydroxyapatite Coating with the (002) Texture

This study reports the effect of titanium (Ti) microstructure on the mechanical properties and surface wettability of thin (<800 nm) hydroxyapatite (HA) coating deposited via radio-frequency (RF) magnetron sputtering. It was revealed that the sand-blasting (SB) and acid etching (AE) of Ti prior deposition led to a wide range of surface roughness in nano/micro scale. After nanostructured HA coating deposition such physico-mechanical characteristics as nanohardness H, Young's modulus E, H/E ratio and H[3]/E[2] were significantly improved. Moreover, HA coatings exhibited improved wear resistance, lower friction coefficient and ability of the coating to wetting

Stydying of morphology and elemental composition of the calcium phosphate layer after treatment by impulse electron beam

One of the effective ways to improve the adhesive properties of biocompatible coatings on implants is using electron-beam melting of the surface, accompanied by a partial or complete mixing area "coating- substrate". The surface of the titanium substrate bearing calcium phosphate coating received by RF magnetron sputter is processed by a pulsed electron beam having an energy density of 0.8 - 8 J/cm2. After treatment by a pulsed electron beam under different regimes significant changes in the topography of the formed surface were observed. Treatment regimes with an energy density of 0.8 J/cm{2} and 3 lead to the thermal annealing of the coating. The use of a beam having an energy density of 8 and 6.5 J/cm{2} leads to partial vaporization and mixing of the coating material with a titanium matrix