Semiconductor THz Lasers and Their Applications in Spectroscopy of Explosives

Recently, applications of THz spectroscopy for detecting explosive agents have attracted much attention due to following reasons: many CBRNE agents have fingerprint-like features in the THz wavelength range; the THz spectroscopy provides an ability for remote and non-destructive identification of explosives; the THz radiation penetrates through many covering dielectric materials including paper, leather, fabric and so on. One of the most important components of THz spectroscopy setups is the source of THz radiation, which has to be high-power, tunable, low-cost and to have compact sizes. In this chapter, we are going to overview recent progress of wide variety of THz emitters considered as candidates for that role. We will pay a special attention to recent trends in engineering of spectral characteristics of THz quantum-cascade lasers and their tunability. Also we will describe the advantages and difficulties that accompany a THz spectroscopy of explosives

Femtosecond parabolic pulse shaping in normally dispersive optical fibers

Formation of parabolic pulses at femtosecond time scale by means of passive nonlinear reshaping in normally dispersive optical fibers is analyzed. Two approaches are examined and compared: the parabolic waveform formation in transient propagation regime and parabolic waveform formation in the steady-state propagation regime. It is found that both approaches could produce parabolic pulses as short as few hundred femtoseconds applying commercially available fibers, specially designed all-normal dispersion photonic crystal fiber and modern femtosecond lasers for pumping. The ranges of parameters providing parabolic pulse formation at the femtosecond time scale are found depending on the initial pulse duration, chirp and energy. Applicability of different fibers for femtosecond pulse shaping is analyzed. Recommendation for shortest parabolic pulse formation is made based on the analysis presented

Design of all-normal dispersion microstructured optical fiber on silica platform for generation of pulse‐preserving supercontinuum under excitation at 1550 nm

We investigated numerically the possibility of all normal dispersion fiber design for near-infrared supercontinuum generation based on a standard air-silica microstructure. The design procedure includes finding of target dispersion profile and subsequent finding of appropriate geometrical fiber design by inverse dispersion engineering. It was shown that the tailoring of dispersion profile could increase the spectral width of generated supercontinuum while maintaining perfect spectral flatness. Conditions necessary for wide and flat supercontinuum generation as well as restrictions imposed by chosen materials were discussed. As a result of design and optimization procedure, an air-silica design was found providing normal dispersion up to 3 μm. Simulation results with 10 nJ, 100 fs pulses demonstrate supercontinuum generation up to 1.3 octave; whereas pumping with 30 nJ, 100 fs pulses could provide 1.8 octave supercontinuum

Formation of ultrashort triangular pulses in optical fibers

Specialty shape ultrashort optical pulses, and triangular pulses in particular, are of great interest in optical signal processing. Compact fiber-based techniques for producing the special pulse waveforms from Gaussian or secant pulses delivered by modern ultrafast lasers are in demand in telecommunications. Using the nonlinear Schr¨odinger equation in an extended form the transformation of ultrashort pulses in a fiber towards triangular shape is characterized by the misfit parameter under variety of incident pulse shapes, energies, and chirps. It is shown that short (1-2 m) conventional single mode fiber can be used for triangular pulse formation in the steady-state regime without any pre-chirping if femtosecond pulses are used for pumping. The pulses obtained are stable and demonstrate linear chirp. The ranges and combinations of the pulse parameters found here will serve as a guide for scheduling the experiments and implementation of various all-fiber schemes for optical signal processing

Supercontinuum generation at 800 nm in all-normal dispersion photonic crystal fiber

We have numerically investigated the supercontinuum generation and pulse compression in a specially designed all-normal dispersion photonic crystal fiber with a flat-top dispersion curve, pumped by typical pulses from state of the art Ti:Sapphire lasers at 800 nm. The optimal combination of pump pulse parameters for a given fiber was found, which provides a wide octave-spanning spectrum with superb spectral flatness (a drop in spectral intensity of ~1.7 dB). With regard to the pulse compression for these spectra, multiple-cycle pulses (~8 fs) can be obtained with the use of a simple quadratic compressor and nearly single-cycle pulses (3.3 fs) can be obtained with the application of full phase compensation. The impact of pump pulse wavelength-shifting relative to the top of the dispersion curve on the generated SC and pulse compression was also investigated. The optimal pump pulse wavelength range was found to be 750nm < \u1d706\u1d45d < 850nm, where the distortions of pulse shape are quite small (< -3.3 dB). The influences of realistic fiber fabrication errors on the SC generation and pulse compression were investigated systematically. We propose that the spectral shape distortions generated by fiber fabrication errors can be significantly attenuated by properly manipulating the pump

Photonic Crystals: Physics and Practical Modeling

The great interest in photonic crystals and their applications in the past decade requires a thorough training of students and professionals who can practically apply the knowledge of physics of photonic crystals together with skills of independent calculation of basic characteristics of photonic crystals and modelling of various photonic crystal elements for application in all-optical communication systems. This book combines basic backgrounds in fiber and integrated optics with detailed analysis of mathematical models for 1D, 2D and 3D photonic crystals and microstructured fibers, as well as with descriptions of real algorithms and codes for practical realization of the models

Dispersion properties of Kolakoski-cladding hollow-core nanophotonic Bragg waveguide

A comprehensive analysis of guided modes of a novel type of a planar Bragg reflection waveguide that consists of a low refractive index guiding layer sandwiched between two finite aperiodic mirrors is presented. The layers in the mirrors are aperiodically arranged according to the Kolakoski substitution rule. In such a waveguide, light is confined inside the core by Bragg reflection, while dispersion characteristics of guided modes strongly depend on aperiodicity of the cladding. Using the transfer matrix formalism bandgap conditions, dispersion characteristics and mode profiles of the guided modes of such a waveguide are studied on the GaAs/AlAs and Si/SiO2 epitaxial platforms, which are compatible with hybrid and heteroepitaxial frameworks of silicon photonics