Running characteristics of aerodynamic bearing with self-lifting capability at low rotational speed

This article has been made available through the Brunel Open Access Publishing Fund - Copyright @ 2011 Tadeusz Adam Stolarski.An aerodynamic journal bearing that is capable of self-generating squeeze-film pressure is presented and its dynamic characteristics investigated numerically and experimentally. A numerical method based on a time-marching static model was applied to assess the orbit trajectory path of the rotor upon a perturbation. Experimental results were obtained to validate the effect of the self-generated squeeze-film pressure on the stability of the rotor. Analyzing the Fast Fourier Transform (FFT) responses of the rotor orbits enabled identification of self-excited whirling instabilities. Both numerical and experimental results showed that increasing the squeeze-film effect of the bearing could raise the threshold speed of instability

Comparative performance of squeeze film air journal bearings made of aluminium and copper

This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and the source are credited. Copyright @ 2012 The Authors - The article can be accessed from the links below.This article has been made available through the Brunel Open Access Publishing Fund.Two tubular squeeze film journal bearings, made from Al 2024 T3 and Cu C101, were excited by driving the single-layer piezoelectric actuators at a 75-V AC with a 75-V DC offset. The input excitation frequencies were coincident with the 13th modal frequency, at 16.32 and 12.18 kHz for the respective Al and Cu bearings, in order to produce a ‘triangular’ modal shape. The paper also provided a CFX model, used to solve the Reynolds equation and the equation of motion, to explain the squeeze film effect of an oscillating plate with pressure end leakage. The dynamic characteristics of both bearings were studied in ANSYS and then validated by experiments with respect to their squeeze film thickness and load-carrying capacity. It was observed that whilst both bearings did levitate a load when excited at mode 13, the Al bearing showed a better floating performance than Cu bearing. This is due to the fact that the Al bearing had a higher modal frequency and a greater amplitude response than the Cu bearing.This article is made available through the Brunel Open Access Publishing Fund

Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact

Commonly used four-ball testing configuration when used to investigate rolling contact behavior of polyetheretherketone (PEEK) produced some unexpected peculiarities, namely direct contact between ceramic balls. Direct contact between lower three balls is normally not expected to take place when elastic materials (ferrous or ceramics) are tested. However, due to the viscoelastic nature of PEEK surface damage of the ceramic balls were observed leading to the production of wear debris which in turn facilitated premature failure of PEEK components of the assembly. It is postulated that caution is required when using the four-ball testing configuration to assess rolling contact performance of viscoelastic materials, such as engineering polymers.Gdansk University of Technology, Gdansk, Poland(Grant DS-2012)

Use of near field acoustic levitation sliding contact

This paper presents an investigation into producing self-levitation effect using piezo-electric actuators (PZT). Self-levitation has been demonstrated and results are presented and discussed. A relationship between the levitation distance and weight of the levitating sample has been found. In addition the orientation and position of the PZTs has been found to affect the levitation distance. Modal shapes of the vibration plates used have been produced through modelling annd found to accurately correlate with the experimental results found. Additional evidence suggests that the type of vibration plate material affects the separation distance, possibly due to the material's properties of acoustic reflection

Acoustic Journal Bearing with Changeable Geometry and Built-in Flexibility

The influence of embodiment flexibility on the performance of an acoustic journal bearing is presented. Two completely different embodiments of the bearing were investigated using three criteria of performance assessment that is torque at the start-up, amount of separation due to squeeze film pressure and motion stability of the shaft running at speed. The embodiment with built-in flexibility proved to perform far better that the bearing which overall flexibility was much less. However, considerations pertinent to the easy of machining and fatigue endurance mitigate the ranking of performance of the two embodiments investigated.National Centre of Scienc

Search for new phenomena in final states with an energetic jet and large missing transverse momentum in pp collisions at √ s = 8 TeV with the ATLAS detector

Results of a search for new phenomena in final states with an energetic jet and large missing transverse momentum are reported. The search uses 20.3 fb−1 of √ s = 8 TeV data collected in 2012 with the ATLAS detector at the LHC. Events are required to have at least one jet with pT > 120 GeV and no leptons. Nine signal regions are considered with increasing missing transverse momentum requirements between Emiss T > 150 GeV and Emiss T > 700 GeV. Good agreement is observed between the number of events in data and Standard Model expectations. The results are translated into exclusion limits on models with either large extra spatial dimensions, pair production of weakly interacting dark matter candidates, or production of very light gravitinos in a gauge-mediated supersymmetric model. In addition, limits on the production of an invisibly decaying Higgs-like boson leading to similar topologies in the final state are presente

Measurement of the cross-section and charge asymmetry of WW bosons produced in proton-proton collisions at s=8\sqrt{s}=8 TeV with the ATLAS detector

This paper presents measurements of the $W^+ \rightarrow \mu^+\nu$ and $W^- \rightarrow \mu^-\nu$ cross-sections and the associated charge asymmetry as a function of the absolute pseudorapidity of the decay muon. The data were collected in proton--proton collisions at a centre-of-mass energy of 8 TeV with the ATLAS experiment at the LHC and correspond to a total integrated luminosity of 20.2~\mbox{fb^{-1}}. The precision of the cross-section measurements varies between 0.8% to 1.5% as a function of the pseudorapidity, excluding the 1.9% uncertainty on the integrated luminosity. The charge asymmetry is measured with an uncertainty between 0.002 and 0.003. The results are compared with predictions based on next-to-next-to-leading-order calculations with various parton distribution functions and have the sensitivity to discriminate between them.Comment: 38 pages in total, author list starting page 22, 5 figures, 4 tables, submitted to EPJC. All figures including auxiliary figures are available at https://atlas.web.cern.ch/Atlas/GROUPS/PHYSICS/PAPERS/STDM-2017-13

Search for direct stau production in events with two hadronic tau-leptons in root s=13 TeV pp collisions with the ATLAS detector

A search for the direct production of the supersymmetric partners ofτ-leptons (staus) in final stateswith two hadronically decayingτ-leptons is presented. The analysis uses a dataset of pp collisions corresponding to an integrated luminosity of139fb−1, recorded with the ATLAS detector at the LargeHadron Collider at a center-of-mass energy of 13 TeV. No significant deviation from the expected StandardModel background is observed. Limits are derived in scenarios of direct production of stau pairs with eachstau decaying into the stable lightest neutralino and oneτ-lepton in simplified models where the two staumass eigenstates are degenerate. Stau masses from 120 GeV to 390 GeV are excluded at 95% confidencelevel for a massless lightest neutralino

Search for chargino-neutralino production with mass splittings near the electroweak scale in three-lepton final states in √s=13 TeV pp collisions with the ATLAS detector

A search for supersymmetry through the pair production of electroweakinos with mass splittings near the electroweak scale and decaying via on-shell W and Z bosons is presented for a three-lepton final state. The analyzed proton-proton collision data taken at a center-of-mass energy of √s=13  TeV were collected between 2015 and 2018 by the ATLAS experiment at the Large Hadron Collider, corresponding to an integrated luminosity of 139  fb−1. A search, emulating the recursive jigsaw reconstruction technique with easily reproducible laboratory-frame variables, is performed. The two excesses observed in the 2015–2016 data recursive jigsaw analysis in the low-mass three-lepton phase space are reproduced. Results with the full data set are in agreement with the Standard Model expectations. They are interpreted to set exclusion limits at the 95% confidence level on simplified models of chargino-neutralino pair production for masses up to 345 GeV

Measurement of VH, H → b b ¯ production as a function of the vector-boson transverse momentum in 13 TeV pp collisions with the ATLAS detector

Cross-sections of associated production of a Higgs boson decaying into bottom-quark pairs and an electroweak gauge boson, W or Z, decaying into leptons are measured as a function of the gauge boson transverse momentum. The measurements are performed in kinematic fiducial volumes defined in the `simplified template cross-section' framework. The results are obtained using 79.8 fb-1 of proton-proton collisions recorded by the ATLAS detector at the Large Hadron Collider at a centre-of-mass energy of 13 TeV. All measurements are found to be in agreement with the Standard Model predictions, and limits are set on the parameters of an effective Lagrangian sensitive to modifications of the Higgs boson couplings to the electroweak gauge bosons