OC5 Project Phase II: Validation of Global Loads of the DeepCwind Floating Semisubmersible Wind Turbine

This paper summarizes the findings from Phase II of the Offshore Code Comparison, Collaboration, Continued, with Correlation project. The project is run under the International Energy Agency Wind Research Task 30, and is focused on validating the tools used for modeling offshore wind systems through the comparison of simulated responses of select system designs to physical test data. Validation activities such as these lead to improvement of offshore wind modeling tools, which will enable the development of more innovative and cost-effective offshore wind designs. For Phase II of the project, numerical models of the DeepCwind floating semisubmersible wind system were validated using measurement data from a 1/50th-scale validation campaign performed at the Maritime Research Institute Netherlands offshore wave basin. Validation of the models was performed by comparing the calculated ultimate and fatigue loads for eight different wave-only and combined wind/wave test cases against the measured data, after calibration was performed using free-decay, wind-only, and wave-only tests. The results show a decent estimation of both the ultimate and fatigue loads for the simulated results, but with a fairly consistent underestimation in the tower and upwind mooring line loads that can be attributed to an underestimation of waveexcitation forces outside the linear wave-excitation region, and the presence of broadband frequency excitation in the experimental measurements from wind. Participant results showed varied agreement with the experimental measurements based on the modeling approach used. Modeling attributes that enabled better agreement included: the use of a dynamic mooring model; wave stretching, or some other hydrodynamic modeling approach that excites frequencies outside the linear wave region; nonlinear wave kinematics models; and unsteady aerodynamics models. Also, it was observed that a Morison-only hydrodynamic modeling approach could create excessive pitch excitation and resulting tower loads in some frequency bands.This work was supported by the U.S. Department of Energy under Contract No. DEAC36- 08GO28308 with the National Renewable Energy Laboratory. Some of the funding for the work was provided by the DOE Office of Energy Efficiency and Renewable Energy, Wind and Water Power Technologies Office

Verification of a Numerical Model of the Offshore Wind Turbine From the Alpha Ventus Wind Farm Within OC5 Phase III

The main objective of the Offshore Code Comparison Collaboration Continuation, with Correlation (OC5) project, is validation of aero-hydro-servo-elastic simulation tools for offshore wind turbines (OWTs) through comparison of simulated results to the response data of physical systems. Phase III of the OC5 project analyzes the Senvion 5M wind turbine supported by the OWEC Quattropod from the alpha ventus offshore wind farm. This paper shows results of the verification of the OWT models (code-to-code comparison). A subsequent publication will focus on their validation (comparison of simulated results to measured physical system response data). Based on the available data, the participants of Phase III set up numerical models of the OWT in their simulation tools. It was necessary to verify and to tune these models. The verification and tuning were performed against an OWT model available at the University of Stuttgart - Stuttgart Wind Energy (SWE) and documentation provided by Senvion and OWEC Tower. A very good match was achieved between the results from the reference SWE model and models set up by OC5 Phase III participants

Numerical solution of the cable dynamic equations using the linearized equivalent damping force

Thesis (Ocean E.)--Massachusetts Institute of Technology, Dept. of Ocean Engineering, 1985.MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING.Bibliography: leaves 62-63.by Hyunkyoung Shin.Ocean E

Nonlinear cable dynamics

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Ocean Engineering, 1987.Bibliography: leaves 174-176.by Hyunkyoung Shin.Ph.D

Model test and numerical simulation of OC3 spar type floating offshore wind turbine

Nowadays, the study on Floating Offshore Wind Turbines (FOWTs) is being performed globally. Dozens of numerical simulation tools have been developed for designing FOWTs and simulating their performances in combined wave and wind environments. On the other hand, model tests are still required to verify the results obtained from numerical simulation tools. To predict seakeeping performance of the OC3-Hywind platform, a OC3 spar model moored by a 3-leg catenary spread mooring system with a delta connection was built with a 1/128 scale ratio. The model tests were carried out for various sea states, including rotating rotor effect with wind in the Ocean Engineering Wide Tank, University Of Ulsan (UOU). The model test results are compared with the numerical simulations by UOU in-house code and FAST. Keywords: UOU+FAST, Floating Offshore Wind Turbine (FOWT), Seakeeping performance, OC3 spar, Model test, RA

Model test of an inverted conical cylinder floating offshore wind turbine moored by a spring-tensioned-leg

A new 5-MW floating offshore wind turbine moored by a spring-tensioned-leg was proposed for installa­tion in about 50m water depth. Its substructure is a platform of the inverted conical cylinder type with massive ballast weight plate at the bottom. A 1:128 scale model was built for the preliminary engineering development. The model tests in waves and wind were carried out to estimate motion characteristics of this platform in the Ocean Engineering Wide Tank of the University of Ulsan. Its motions were measured and the RAOs were compared. The proposed floating off­shore wind turbine showed a good stability and decent responses in waves, wind and operation of the wind turbine

Experimental investigation of slamming impact acted on flat bottom bodies and cumulative damage

Most offshore structures including offshore wind turbines, ships, etc. suffer from the impulsive pressure loads due to slamming phenomena in rough waves. The effects of elasticity & plasticity on such slamming loads are investigated through wet free drop test results of several steel unstiffened flat bottom bodies in the rectangular water tank. Also, their cumulative deformations by consecutively repetitive free drops from 1000 mm to 2000 mm in height are measured. Keywords: Slamming phenomena, Impulsive pressure load, Wet free drop test, Flat bottom body, Cumulative damag

Optimized Supply Chain Management of Rice in South Korea: Location–Allocation Model of Rice Production

Planning for optimized farming with the aim of providing ideal site and cultivar selection is critical for a stable and sustainable supply of rice with sufficient quantity and quality to customers. In this study, a range of morphological characteristics and yield of eight rice cultivars that are commonly cultivated in Korea were investigated from 2005 to 2020. All morphological characteristics were significantly different among the eight rice cultivars. The dataset of morphological characteristics and yield was used to isolate groups of similar rice cultivars. The k-means clustering method was used to group the rice cultivars. Three groups (Group 1, Group 2, and Group 3) were created. Most cultivars were in Group 1. High-yielding rice cultivars were in Group 2, while the rice cultivars in Group 3 had the lowest rice grain yield. After grouping these rice cultivars, ideal farming locations for all three rice cultivar groups were identified to reduce transportation cost using an optimized location–allocation model. Simulation results suggested the following: (1) Group 1 should be produced in Jellanam-do (south west region), (2) Group 2 should be produced in Chungcheongnam-do (central west region), and (3) Group 3 should be mainly produced in the central west region of South Korea. Simulation results showed the potential to reduce transportation cost by around 0.014%. This can also reduce 21.04 tons of CO2 emission from a freight truck. Because these eight cultivars only make up 19.76% of the total rice production in South Korea, the cost reduction proportion was only 0.014% of total revenue. In future studies, more rice cultivars should be investigated to increase the efficiency of the model performance

Study on the Motion Characteristics of 10 MW Superconducting Floating Offshore Wind Turbine Considering 2nd Order Wave Effect

Recently, several countries have made commitments to move to a net-zero emission by the year 2050 in a response to climate change. Among various renewable energy systems to realize the target, wind energy system has been gaining much attention as a favorable alternative source to fossil fuel energy. In particular, many floating offshore wind turbines (FOWT) are expected to be installed because of vast installation resources without water depth limit conditions, stable and strong wind resources, relatively low constraints on noise emission, and space restriction compared to onshore wind turbines. In this study, a 10 MW superconducting floating offshore wind turbine was modeled with a 1/90 scale ratio and was experimentally tested at the Ocean Engineering Widetank of the University of Ulsan. The model calibration of the scaled model was performed with free decay test and showed a good correlation with simulation results calculated from FAST V8 of NREL. The motion characteristics of the 10 MW superconducting FOWT semi-submersible type platform was investigated under regular waves and irregular waves through the comparison of model test data and simulation results. The study on the motion characteristics of the model showed that the simulation considering the 2nd order wave effects to hydrodynamic forces and moments provided better accuracy close to the model test data