Output feedback control of linear multipass processes

An error actuated output feedback controller for a sub-class of linear multipass processes designated as 'differential unit memory' is defined. Further, the design of this controller for closed-loop stability is considered. In particular, a recently developed computationally feasible stability tesits used to present some preliminary work on this problem

A mechanism for high-frequency oscillation in ramjet combustors and afterburners

An experimental investigation was made of the behavior of a small two-dimensional combustion chamber, burning a uniform mixture of air and fuel vapor under conditions of high-frequency oscillation or screech. Measurements were made of the limits of stable screech, the amplitude and frequency of pressure oscillations over a wide range of mixture ratio, inlet air temperature, and combustor flow rate. Spark schlieren photographs and high-speed motion pictures taken of the combustion process showed, in agreement with other investigations, that the high-frequency oscillation is accompanied by vortices shed periodically from the flameholder lip with the same frequency as the oscillation. The following mechanism of exciting the oscillations is suggested. A mode of transverse oscillation is excited as the result of periodic transport of combustible material, associated with the vortices, into the hot wake of the flameholder. The vortices, in turn, are generated at the flameholder lips by the fluctuating transverse velocity. When the ignition time delay lies in the proper range, the phase relationship between oscillations in transverse velocity and combustion intensity is such that the oscillation is amplified

The sensitivity of a very long baseline interferometer

The theoretical sensitivity of various methods of acquiring and processing interferometer data are compared. It is shown that for a fixed digital recording capacity one bit quantization of single sideband data filtered with a rectangular bandpass and sampled at the Nyquist rate yields the optimum signal to noise ratio. The losses which result from imperfect bandpass, poor image rejection, approximate methods of fringe rotation, fractional bit correction, and loss of quadrature are discussed. Also discussed is the use of the complex delay function as a maximum likelihood fringe estimator

Phase and group delay calibration of a very long baseline interferometer by East Coast VLBI Group

Precisely timed pulses injected into the input of each receiver are used to calibrate the phase and group delay through each interferometer terminal. The short duration pulses are generated at a 1 MHz rate directly from the output of the frequency standard. The pulses are injected into the receiver at a level low enough to produce less than one percent increase in system temperature, yet can be extracted during processing with a high enough signal to noise ratio to determine the phase of the calibration rails within 1 degree in 1 second of integration. The calibration system also includes precise cable measurement electronics and a pulse echo for clock synchronization

Microwaves to megabits

Receiver and terminal characteristics of the Mark 3 very long baseline interferometry system are described in some detail. The Mark 3 system has 14 IF to video converters, each with built in synthesized local oscillators which have a range of 100 to 500 MHz covered in 10 kHz steps. In the normal wideband continuum mode, all 14 upper and all 14 lower sideband video outputs (each with 2 MHz bandwidth) are recorded with a total data rate of 112 Mbits/sec. In geodetic observations, two IF bands are simultaneously recorded from a dual band (5/X) receiver

Study to demonstrate the feasibility of and determine the optimum method of remote haze monitoring by satellite

There are no author-identified significant results in this report

A Behavioral Approach to the Control of Discrete Linear Repetitive Processes

This paper formulates the theory of linear discrete time repetitive processes in the setting of behavioral systems theory. A behavioral, latent variable model for repetitive processes is developed and for the physically defined inputs and outputs as manifest variables, a kernel representation of their behavior is determined. Conditions for external stability and controllability of the behavior are then obtained. A sufficient condition for stabilizability is also developed for the behavior and it is shown under a mild restriction that, whenever the repetitive system is stabilizable, a regular constant output feedback stabilizing controller exists. Next a notion of eigenvalues is defined for the repetitive process under an action of a closed loop controller. It is then shown how under controllability of the original repetitive process, an arbitrary assignment of eigenvalues for the closed loop response can be achieved by a constant gain output feedback controller under the above restriction. These results on the existence of constant gain output feedback controllers are among the most striking properties enjoyed by repetitive systems, discovered in this paper. Results of this paper utilize the behavioral model of the repetitive process which is an analogue of the 1D equivalent model of the dynamics studied in earlier work on repetitive processes

Amplification efficiency and thermal stability of qPCR instrumentation: Current landscape and future perspectives

This is a final draft version of the publication following acceptance by the journal.Quantitative polymerase chain reaction (qPCR) is a method of amplifying and detecting small samples of genetic material in real time and is in routine use across many laboratories. Speed and thermal uniformity, two important factors in a qPCR test, are in direct conflict with one another in conventional peltier‑driven thermal cyclers. To overcome this, companies are developing novel thermal systems for qPCR testing. More recently, qPCR technology has developed to enable its use in point‑of‑care testing (POCT), where the test is administered and results are obtained in a single visit to a health provider, particularly in developing countries. For a system to be suitable for POCT it must be rapid and reliable. In the present study, the speed and thermal uniformity of four qPCR thermal cyclers currently available were compared, two of which use the conventional peltier/block heating method and two of which use novel heating and cooling methods