63 research outputs found
Recommended from our members
Combinatorial Exploration of Novel Transparent Conducting Oxide Materials
High-throughput combinatorial approaches have been used for the discovery and optimization of transparent conducting oxide (TCO) materials for PV applications. We report on current investigations in In-Zn-O, In-Ti-O and In-Mo-O systems. The InZnO system is shown to be amorphous in the best conducting range with a conductivity of ~ 3000 Ω-cm-1 for 50%-70% In/Zn. The amorphous InZnO films are very smooth (2..ANG.. rms). In-Ti-O is found to be an excellent high-mobility TCO with mobilities of greater than 80 cm2/v-sec and conductivities of more than 6000 Ω-cm-1 for sputtered thin film materials
Recommended from our members
Compaction of spray-dried ceramic powders: An experimental study of the factors that control green density
The pressure-compaction response of a spray-dried, 94% alumina powder containing several percent of a polymeric binder was investigated as a function of die diameter and compact aspect ratio. The results show that the die fill density decreases markedly with decreasing die diameter and aspect ratio, while the final green density (at 120 MPa) decreases only slightly under the same conditions. These results suggest that the ratio of the initial compact dimensions to the size of the granules may be much more important than previously considered
Recommended from our members
Applied mechanics modeling of granulated ceramic powder compaction
In ceramic manufacturing processes such as dry-pressing, correlations between applied compacting pressure and resultant powder compact density are essential for defining reliable process conditions for ceramic components. Pressure-density diagrams have been developed as a tool for both process control and for understanding the compaction behavior of different powders. These types of diagrams, however, pertain only to the averag@ properties of a powder compact and do not address a significant issue in powder compaction processes: the formation of density gradients within the compact. Continuum-based mechanics models of varying complexity have addressed the influence of frictional forces acting at the powder-die wall interface which dissipate the applied pressure throughout the compact. Resulting pressure distribution models are then typically coupled with empirical functions relating pressure and density to obtain a green density distribution in the compact. All of these models predict similar trends; however, none predict the distribution with sufficient accuracy to be considered as a design tool for industrial applications
Recommended from our members
Ceramic compaction models: Useful design tools or simple trend indicators?
It is well-known that dry pressing of ceramic powders leads to density gradients in a ceramic compact resulting in non-uniform shrinkage during densification. This necessitates diamond grinding to final dimensions which, in addition to being an extra processing step, greatly increases the manufacturing cost of ceramic components. To develop methods to control and thus mitigate density variations in compacted powders, it has been an objective of researchers to better understand the mechanics of the compaction process and the underlying material and tooling effects on the formation of density gradients. This paper presents a review of models existing in the literature related to the compaction behavior of ceramic powders. In particular, this paper focuses on several well-known compaction models that predict pressure and density variations in powder compacts
Recommended from our members
Characterization techniques to validate models of density variations in pressed powder compacts
Techniques for characterizing density gradients generated during typical powder compaction processes are reviewed and several are evaluated. The techniques reviewed are ultrasonic velocity measurements, laser ultrasonic velocity measurements, x-ray radiography, autoradiography, computer tomography (CT), magnetic resonance imaging (MRI), and simple image analysis of polished cross-sections. Experimental results are reported for all of these techniques except autoradiography, CT and MRI. The test specimens examined were right circular cylinders of a high length/diameter ratio (to ensure significant density variation) pressed from commercial spray-dried alumina powders. Although the density gradients could be detected with all four techniques, ultrasonic velocity measurements gave the best contour map of gradients and is therefore most suitable for model validation. On the other hand, it was concluded that x-ray radiography is preferable in situations where cost and/or number of samples are more important that high resolution
Recommended from our members
Characterization of microstructure and crack propagation in alumina using orientation imaging microscopy (OIM). December 1996
A more complete description requires the lattice orientations of a statistically significant number of grains, coupled with morphology such as grain size and shape; this can be obtained using orientation imaging microscopy (OIM), which uses crystallographic orientation data from Backscattered Electron Kikuchi patterns (BEKP) collected using a SEM. This report describes the OIM results for alumina; these include image quality maps, grain boundary maps, pole figures, and lattice misorientations depicted on MacKenzie plot and in Rodrigues space. High quality BEKP were obtained and the images and data readily reveal the grain morphology, texture, and grain boundary misorientations, including those for cracked boundaries. A larger number of grains should be measured to make statistical comparisons between materials with different processing histories
- …