Effects of Hot Isostatic Pressing on the Properties of Laser-Powder Bed Fusion Fabricated Water Atomized 25Cr7Ni Stainless Steel

25Cr7Ni stainless steel (super duplex stainless steels) exhibits a duplex microstructure of ferrite and austenite, resulting in an excellent combination of high strength and corrosion resistance. However, Laser-Powder Bed Fusion fabrication of a water-atomized 25Cr7Ni stainless steel of novel chemical composition resulted in a purely ferritic microstructure and over 5% porosity. The current study investigated the effects of two hot isostatic pressing parameters on the physical, mechanical, and corrosion properties as well as microstructures of water-atomized 25Cr7Ni stainless steel of novel composition fabricated by L-PBF for the first time in the literature. The corrosion behaviour was studied using linear sweep voltammetry in a 3.5% NaCl solution. The Hot Isostatic Pressing-treated sample achieved over 98% densification with a corresponding reduction in porosity to less than 0.1% and about 3 similar to 4% in annihilation of dislocation density. A duplex microstructure of ferrite 60% and austenite 40%was observed in the X-Ray Diffraction and etched metallography of the HIP-treated samples from a purely ferritic microstructure prior to the HIP treatment. With the evolution of austenite phase, the HIP-treated samples recorded a decrease in Ultimate Tensile Strength, yield strength, and hardness in comparison with as-printed samples. The variation in the morphology of the evolved austenite grains in the HIP-treated samples was observed to have a significant effect on the elongation. With a reduction in porosity and the evolution of the austenite phase, the HIP-treated samples showed a higher corrosion resistance in comparison with the as-printed samples

Powder Injection Molding of Ceria-Stabilized, Zirconia-Toughened Mullite Parts for UAV Engine Components

Powder injection molding (PIM) of ceria-stabilized, zirconia-toughened mullite composites were investigated in the present article with the goal of obtaining performance enhancement in complex geometries for energy and transportation applications. A powder-polymer mixture (feedstock) was developed and characterized to determine its suitability for fabricating complex components using the PIM process. Test specimens were injection molded and subsequently debound and sintered. The sintered properties indicated suitable properties for engine component applications used in unmanned aerial vehicles (UAVs). The measured feedstock properties were used in computer simulations to assess the mold-filling behavior for a miniature turbine stator. The results from the measurements of rheological and thermal properties of the feedstock combined with the sintered properties of the ceria-stabilized, zirconia-toughened mullite strongly indicate the potential for enhancing the performance of complex geometries used in demanding operating conditions in UAV engines

The Effects of Nanoparticle Addition on Binder Removal from Injection Molded Aluminum Nitride

The effects of nanoparticle addition on the multi-step debinding of injection molded aluminum nitride (AlN) samples were studied. Experiments varying the solvent debinding conditions (time, temperature and aspect ratio) were performed on monomodal, microscale (μ) and bimodal, micro-nanoscale (μ-n) AlN samples. Variations in the solvent debinding kinetics as a result of the reduced particle size and increased powder content were examined. The bimodal μ-n AlN samples showed a slower solvent extraction of binder components compared to monomodal μ-AlN samples. The activation energy for solvent extraction estimated from diffusion coefficients (Arrhenius equation) was in close agreement with the value estimated by the master debinding curve (MDC) method. An activation value around 50 kJ/mole was estimated by both the methods for μ and μ-n AlN samples. The thermal debinding behavior of dewaxed samples was also studied and the trends correlated with the solvent debinding behavior.Keywords: Master debinding curves, Diffusion coefficients, Solvent debinding, Bimodal, Activation energy, Monomoda

The Effect of Nanoparticle Addition on SiC and AlN Powder-Polymer Mixtures: Part I. Packing & Flow Behavior

The development of methods to increase sintered density and improve dimensional tolerances is a crucial issue in powder metallurgy and ceramic processing. Increasing the packing density of starting powders is one effective route to achieve high sintered density and dimensional precision. The current paper presents an in-depth study on the effect of nanoparticle addition on the powder content of SiC and AlN powder-polymer mixtures. In particular, bimodal mixtures of nanoscale and sub-micrometer particles were found to have significantly increased powder volume fraction (solids loading) in the mixtures for injection molding. This observation to increasing packing density by using nanoparticles is surprising and novel since nanoparticles are known to inherently exhibit poor packing behavior. Additionally, for a given volume fraction of powder, the bimodal μ-n suspensions had a lower viscosity at any shear rate compared to the monomodal μ- suspensions. The ability to lower the suspension viscosity by adding nanoparticles to micron-sized particles has important implications for processing of particulate suspensions by powder injection molding (PIM), extrusion, slip casting and tape casting. Samples made from bimodal powders exhibited slower polymer removal during debinding and higher densification with lower shrinkage on sintering compared to the corresponding samples made from monomodal powder mixtures.Keywords: Rheology, Packing fraction, Aluminum nitride, Nanoparticles, Silicon carbide, Bimodal mixturesKeywords: Rheology, Packing fraction, Aluminum nitride, Nanoparticles, Silicon carbide, Bimodal mixture

Effects of Hot Isostatic Pressing on the Properties of Laser-Powder Bed Fusion Fabricated Water Atomized 25Cr7Ni Stainless Steel

25Cr7Ni stainless steel (super duplex stainless steels) exhibits a duplex microstructure of ferrite and austenite, resulting in an excellent combination of high strength and corrosion resistance. However, Laser-Powder Bed Fusion fabrication of a water-atomized 25Cr7Ni stainless steel of novel chemical composition resulted in a purely ferritic microstructure and over 5% porosity. The current study investigated the effects of two hot isostatic pressing parameters on the physical, mechanical, and corrosion properties as well as microstructures of water-atomized 25Cr7Ni stainless steel of novel composition fabricated by L-PBF for the first time in the literature. The corrosion behaviour was studied using linear sweep voltammetry in a 3.5% NaCl solution. The Hot Isostatic Pressing-treated sample achieved over 98% densification with a corresponding reduction in porosity to less than 0.1% and about 3~4% in annihilation of dislocation density. A duplex microstructure of ferrite 60% and austenite 40%was observed in the X-Ray Diffraction and etched metallography of the HIP-treated samples from a purely ferritic microstructure prior to the HIP treatment. With the evolution of austenite phase, the HIP-treated samples recorded a decrease in Ultimate Tensile Strength, yield strength, and hardness in comparison with as-printed samples. The variation in the morphology of the evolved austenite grains in the HIP-treated samples was observed to have a significant effect on the elongation. With a reduction in porosity and the evolution of the austenite phase, the HIP-treated samples showed a higher corrosion resistance in comparison with the as-printed samples

Structure and thermal stability of cellulose nanocrystal/polysulfone nanocomposites

The thermal stability of nanocomposites of cellulose nanocrystals (CNC) dispersed in polysulfone (PSf) was studied to understand the influence of heating rate and CNC concentration using thermogravimetric analysis (TGA). While heating rate was found to have a positive influence on the degradation onset temperature and the maximum degradation rate (Tmax) of these nanocomposites. The influence of CNC concentration appeared to be relatively low on these parameters. PSf/CNC nanocomposites with up to 2 wt.% CNC were found to follow first order degradation kinetics and at higher concentrations, better fit was seen with second-order degradation kinetics. The activation energy associated with nanocomposites degradation, determined using Kissinger method, revealed strong stabilizing effect of PSf matrix on CNC filler. FTIR analysis showed signature peak shifts that correlated with PSf/CNC interactions. On the other hand, the CNC filler had marginal influence on the stability of PSf matrix. Master decomposition curve (MDC) and weight-time-temperature plots were constructed from the obtained activation energies to describe the time-temperature dependence of the PSf/CNC nanocomposite pyrolysis

Effects of Powder Characteristics and Chemical Composition on the Properties of 25Cr7Ni Stainless Steel Fabricated by Laser-Powder Bed Fusion and Evaluation of Process Simulation

The 25Cr7Ni stainless steel alloy system is gaining increasing interest in the oil and gas industry because of its combination of high strength and corrosion resistance properties. However, very few studies on the effects of starting powder attributes and chemical composition on the as-printed properties of 25Cr7Ni stainless steel fabricated through laser-powder bed fusion (L-PBF) exist in the literature. This study examined the influence of powder attributes and chemical composition on the samples from gas atomized and water atomized 25Cr7Ni stainless steel powders, fabricated through L-PBF, on their as-printed microstructure and properties. The mechanical properties that were examined included ultimate tensile strength (UTS), elongation (%), and hardness. The corrosion behavior was also studied using linear sweep voltammetry in 3.5 wt.% NaCl solution. The evolved phases were characterized using optical and scanning electron microscopy, as well as through X-ray diffraction. The gas atomized powders, with their spherical and uniform morphology, yielded as-printed parts of higher relative densities when compared to water atomized powders, with irregular morphology due to better powder bed compaction. The higher densification obtained in the L-PBF samples from gas atomized powders translated into the highest UTS, hardness, and yield strength among the L-PBF samples from water atomized powders and wrought–annealed 25Cr7Ni stainless steel. The presence of higher amounts of N and Mn in the chemical composition of the gas atomized powders over water atomized powders promoted the presence of retained austenite in the corresponding L-PBF samples. Higher amounts of Mo, combined with austenite content, yielded a higher corrosion resistance in the L-PBF samples from the gas atomized powder than in the L-PBF samples from the water atomized powders. The latter part of the work is focused on the evaluation of simulation parameters for analyzing the fabrication procedure for the L-PBF process using Simufact software. For a given set of process parameters, Simufact provides the distortion and internal stresses developed in the printed parts as output. The present study sought to evaluate the process simulation by comparing the experimental observations in terms of the part distortion achieved in a stainless steel cube fabricated through L-PBF with Simufact process simulation obtained using the same set of process parameters