In situ synchrotron radiation diffraction investigation of the compression behaviour at 350 °C of ZK40 alloys with addition of CaO and Y

The evolution of the microstructure during compression is investigated with in situ synchrotron radiation diffraction in as-cast ZK40, ZK40-2CaO and ZK40-1Y Mg alloys. The specimens were compressed at 350 °C with a strain rate of 10−3 s−1 until 30% deformation. The Y containing alloy showed the highest 0.2% proof strength in compression of 35 MPa at 350 °C which is double that of the ZK40 alloy, while the CaO added alloy shows a moderate increment at 23 MPa. The Y containing alloy shows some work hardening, while the CaO modified and the ZK40 alloys do not show work hardening after yield. Synchrotron radiation diffraction timelines show that continuous and discontinuous dynamic recrystallization occurs during deformation of the ZK40 alloy while a small amount of dynamic recrystallization was observed in the ZK40-1Y alloy. However, dynamic recrystallization was not present in the ZK40-2CaO alloy. SEM-EBSD analysis conducted on the deformed samples shows a significantly high volume fraction of twins in the Y and CaO containing alloys which was absent in the ZK40 alloy. The modified deformation behaviours observed in the CaO and Y containing alloys were attributed to the presence of intermetallic particles found at the grain boundaries and to the role of Ca and Y in stabilising twinning.The authors acknowledge the Deutsches Elektronen-Synchro-tron for the provision of facilities within the framework of proposal I-20130434.RHBacknowledgesUniversityofSãoPaulofor granting the fellowship 'Bolsa Empreendedorismo'

On the influence of solution and ageing treatments on the microstructure of ZK40 alloys modified with Ca, Gd, Nd and y additions

Abstract As-cast ZK40 alloys, modified with the addition of CaO, Gd, Nd and Y were investigated. Solution heat treatments were performed based on differential thermal analysis results. The unmodified ZK40 alloy exhibited microstructure with nearly no intermetallic compound but with precipitates formed during the solution treatment. The modified ZK40 alloys exhibited a semi-dissolved network of intermetallic compounds along the grain boundaries and zones of intermetallic compounds within the grains. Interestingly, no precipitates were observed immediately next to the grain boundaries. The energy dispersive X-ray spectroscopy line scans showed an enrichment of Zn and Zr in the regions where the precipitates are found, suggesting that they are Zn-Zr precipitates. The ageing behaviour was compared between the as-cast and the solution treated materials and it was found that apart from the ZK40-Gd, ZK40-Nd and ZK40-Y aged at 200 °C after solution treatment, there is no notable ageing response for the investigated alloys.</jats:p

Thixomolded AZ91D and MRI153M magnesium alloys and their enhanced corrosion resistance

© 2020 The Authors. Materials and Corrosion published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim AZ91D and MRI153M alloys were produced by thixomolding. Their corrosion resistance is significantly higher than that of similar materials produced by ingot or die-casting. A corrosion rate smaller than 0.2 mm/year in 5 wt% NaCl solution is measured for the thixomolded AZ91D alloy. The corrosion behaviour was evaluated using immersion tests, electrochemical impedance spectroscopy, hydrogen evolution, glow discharge optical emission spectroscopy, and atomic emission spectroelectrochemistry. A bimodal microstructure is observed for both alloys, with the presence of coarse primary α-Mg grains, fine secondary α-Mg grains, β-phase, and other phases with a minor volume fraction. The amount of coarse primary α-Mg is significantly higher for the AZ91D compared with the MRI153M. The network of β-phase around the fine secondary α-Mg grains is better established in the thixomolded AZ91D alloy. A combination of several factors such as the ratio of primary to secondary α-Mg grains, localised corrosion or barrier effect due to other phases, as well as regions of preferential dissolution of the α-Mg due to chemical segregation, are thought to be responsible for the high corrosion resistance exhibited by the thixomolded AZ91D and MRI153M.German Ministry of Education and Research; Christian Doppler Societ