Properties of jet-plated Ni coating on Ti alloy (Ti6Al4V) with laser cleaning pretreatment

The surface mechanical properties of the Selective Laser Melting (SLM) formed Ti6Al4V samples were improved by adopting a novel laser cleaning pretreatment process combined with a jet electrodeposition process. This paper aimed to investigate the effects of different laser powers on the morphologies and adhesions of the nickel coatings. The advantages of the laser cleaning process are no grinding, no contact, high efficiency and environmental protection. The morphologies, adhesion, wear resistance, and hardness of the coatings were characterized. The results indicate that when the laser energy density reached 20% (4 J/cm2), the contaminations on the substrate and the oxide layer were removed and the crystalline grain of the coating was 15.3 nm. The shallow pits generated by laser burning increased the adhesion of the coatings. In addition, when the laser energy density increased to 6 J/cm2, a yellow oxide layer was produced on the surface of the cleaned titanium alloy. Moreover, the wear resistance of the titanium alloy after the nickel plating was improved. The wear volume was only 0.046 mm3, and the hardness increased to 1967.6 N/mm2

Additive manufacturing of monolithic microwave dielectric ceramic filters via digital light processing

Microwave dielectric ceramics are employed in filters as electromagnetic wave propagation media. Based on additive manufacturing (AM) techniques, microwave dielectric ceramic filters with complex and precise structures can be fabricated to satisfy filtering requirements. Digital light processing (DLP) is a promising AM technique that is capable of producing filters with high accuracy and efficiency. In this paper, monolithic filters made from Al2O3 and TiO2, with a molar ratio of 9:1 (0.9 Al2O3-0.1 TiO2), were fabricated by DLP. The difference in the dielectric properties between the as-sintered and post-annealed samples at different temperatures was studied. The experimental results showed that when sintered at 1550 °C for 2 h and post annealed at 1000 °C for 5 h, 0.9 Al2O3-0.1 TiO2 exhibited excellent dielectric properties: εr = 12.4, Q × f = 111,000 GHz, τf = +1.2 ppm/°C. After comparing the measured results with the simulated ones in the passband from 6.5 to 9 GHz, it was concluded that the insertion loss (IL) and return loss (RL) of the filter meet the design requirements

Study on defect-free debinding green body of ceramic formed by DLP technology

Zirconia and hydroxyapatite(HA) are two typical implant materials, which have the advantages of excellent mechanical strength and good biological activity respectively. It was found that composite material had good biocompatibility and mechanical strength compared to the single material. In this paper, the porous scaffolds of ZrO2/HA composite were formed by digital light processing (DLP) technology and their performance were evaluated. Cell experiments showed that the addition of HA had a positive effect on cell proliferation and differentiation. Mechanical tests showed that the composite scaffold with 10 wt% HA had the best compressive capacity due to the pinning and bridging effect of a small amount of HA grains. When scaffolds were immersed in the simulated body fluid (SBF), the compressive strengths of the composite scaffolds decreased within the first 14 days and gradually increased after 14 days. The reason for this phenomenon was the degradation of calcium phosphate components and the deposition of apatite. By the 28th day, the compressive strengths of all the composite scaffolds increased to over 20 MPa, close to that of the zirconia scaffolds during the same period (25 MPa). The compressive strengths of all scaffolds met the requirement of cancellous bone during the entire soaking period, and the composite scaffolds have potential application value in bone repair

Robust estimation of bacterial cell count from optical density

Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data

Numerical Simulation and Experimental Investigation of Laser Ablation of Al2O3 Ceramic Coating

This paper presents an evaluation of the molten pool laser damage done to an Al2O3 ceramic coating. Mechanism analysis of the laser damage allowed for a 2D finite element model of laser ablation of the Al2O3 ceramic coating to be built. It consisted of heat transfer, laminar flow, and a solid mechanics module with the level set method. Results showed that the laser damage mechanisms through laser ablation were melting, gasification, spattering, and micro-cracking. The ablation depth and diameter increased with the increasing laser ablation time under continuous irradiation. The simulation profile was consistent with the experimental one. Additionally, the stress produced by the laser ablation was 3500–9000 MPa, which exceeded the tensile stress (350–500 MPa), and fracturing and micro-cracks occurred. Laser damage analysis was performed via COMSOL Multiphysics to predict laser damage morphology, and validate the 3D surface profiler and scanning electron microscope results

Effects of Rapid Quenching on Grain Boundary Microstructure and Mechanical Properties of an Al-Mg-Si-Cu Alloy

Precipitate free zones (PFZs) near grain boundaries generally soften alloys. The quenching rate after solution treatment is an important factor influencing the width of PFZs in Al-Mg-Si-Cu alloy. This study explored the effects of high quenching rates on the grain boundary microstructures and mechanical properties of an Al-Mg-Si-Cu alloy. Samples of various thickness were quenched in water at room temperature and in ethylene glycol at −40 °C, respectively. The results showed that the rapidly quenched samples at −40 °C exhibited better comprehensive mechanical properties than the water-quenched samples. Transmission electron microscopy studies revealed the rapidly quenched samples had wider PFZs, shorter intragranular precipitates, and larger grain boundary precipitates (GBPs) than water-quenched samples. It is proposed that when the quenching rate exceeds the critical cooling rate, e.g., in water quenching or rapid quenching, the formation of PFZs is controlled by the solute depletion mechanism rather than the vacancy depletion mechanism. The nucleation and growth of GBPs thus lead to the depletion of solute atoms, resulting in wider PFZs rather than thinner PFZs according to previous knowledge. This research provides valuable insights into the application of rapid quenching technology for modifying alloys’ microstructures and properties