37 research outputs found
Electrolyte effects on polyacrylic acid-polyvinylpyrrolidone aqueous glycol mixtures for use as de-icing fluids
Rheological and wind tunnels measurements are presented for mixtures of polymers polyacrylic acid [PAA] and polyvinylpyrrolidone [PVP] polymers dispersed in water-1,2 propylene glycol mixture to examine their use as potential aircraft de-icing fluids. PAA solutions which form the basis of de-icing fluids are known to result in undesirable gelation which may lead to undesirable and catastrophic consequences in such applications. In this study, we examine the blending of PVP with PAA blends as alternative de-icing fluid formulations that can reduce the likelihood of forming such irreversible gel deposits. Through adjustment of the electrolyte concentration, the ratio of PAA to PVP as well as the molecular weight of PVP, it is possible to achieve a required viscosity profile to that exhibited by a model de-icing fluid across a range of appropriate temperatures. Wind tunnel tests indicate that the mixtures are capable of meeting the necessary requirements for boundary layer depletion as well as having sufficient capability of retaining a stable layer required during aircraft taxiing
Gas permeation and positron annihilation lifetime spectroscopy of poly(ether imides) containing main chain ethylene oxide segments
This article reports a study of four poly(ether imide)s with varying ethylene oxide (EO) segments lengths using positron annihilation lifetimes spectroscopy, wide angle X-ray diffraction, and gas transport measurements. The measured properties change with the length of the EO segment. Comparison of the poly(ether imide) containing a single ether linkage with those containing one and three EO units, show progressive changes of the permeability and diffusion coefficient with void size. However, when six EO units are incorporated into the polymer backbone certain of the observed trends are reversed. Incorporation of flexible EO segments in the polymer backbone allows changes in the chain-chain interactions which increases the packing density and changes the void size and influences the solubility coefficients leading to variation of the gas transport characteristics. Differences in the measured solubility parameters reflect the extent to which the gases molecules are able to interact with the polymer matrix. The highest values obtained for the gas separation for carbon dioxide and nitrogen is observed when EO has a value of three. Further increasing of the length of the EO segments in the poly(ether imide) leads to a reduction the gas transport properties and hence the extent to which gas separation would be achieved
Reconstruction of the spatial dependency of dielectric and geometrical properties of adhesively bonded structures
An inverse problem motivated by the nondestructive testing of adhesively bonded structures used in the aircraft industry is studied. Using transmission line theory, a model is developed which, when supplied with electrical and geometrical parameters, accurately predicts the reflection coefficient associated with such structures. Particular attention is paid to modelling the connection between the structures and the equipment used to measure the reflection coefficient. The inverse problem is then studied and an optimization approach employed to recover these electrical and geometrical parameters from experimentally obtained data. In particular the approach focuses on the recovery of spatially varying geometrical parameters as this is paramount to the successful reconstruction of electrical parameters. Reconstructions of structure geometry using this method are found to be in close agreement with experimental observations
Effect of surface treatments of titanium dioxide pigments on the cure of polyester/triglycidyl isocyanurate powder coatings
Titanium dioxide pigments will typically have an inorganic surface coating based on a blend of alumina and silica and an organic treatment. Both the organic and inorganic treatments can influence the cure characteristics of polyester powder coatings. This paper attempts to explore the connectivity between the nature of the coating and the cure behavior of a typical heat-cured epoxidized isocyanurate formulation. It is found that a high silica:alumina content in the inorganic pacification layer significantly retards the cure process, but is influenced by the nature of the organic treatment. The organic surface treatment may accelerate or retard the initial cure process and gelation times. Elemental analysis indicates that some of the pigments studied have a significantly higher zirconium content and exhibited enhanced cure rates compared with those with the lower zirconium content. This paper illustrates the potential effects of different grades of titanium dioxide on the cure of polyester powder coatings
The effect of alkalisation on the mechanical properties of natural fibres
A study on the effect of alkalisaton using 3% NaOH solution was carried out on Flax, Kenaf, Abaca and Sisal to observe the impact that the common pre-treatment process has on fibre mechanical properties. The result of the investigation indicated that over-treatment of natural fibres using NaOH could have a negative effect on the base fibre properties. It is concluded that a treatment time of less than 10 minutes is sufficient to remove hemicelluloses and to give the optimum effect
Vacuum infusion of natural fibre composites for structural applications
Numerous methods of manufacturing natural fibre composites have been reported in the literature, including compression moudling, often in conjunction with a hot press. Other forms of composite manufacture include 'Vacuum Assisted Resin Transfer Moulding' (VATRM) and the 'Seemann Composite Resin Infusion Moulding Process' (SCRIMP). These methods have been reported to produce natural fibre composies with reasonable mechanical properties [1-2]. In this paper, a vacuum infusion rig is described that has been developed to produce consistent quality composite plates for studies into optimising natural fibre composites. The process aims to harness the benefits of vacuum infusion and compression moulding, where vacuum infusion encourages the removal of trapped air in the system and hence avoid reduction, and additional compression moulding can help to achieve high volume fractions that are otherwise difficult in other processes
Mechanical testing of natural fibre reinforced polyester resin composites and Mode 1 fracture toughness testing of resin blocks
Recent European Parliament directive requires companies to achieve materials recycling greater than 80% in particular in the automotive sector [1]. The research on natural fibre based composite materials fits well into this ecological image. The advantages of natural fibres over synthetic materials include, low density, relative cheapness, availability and biodegradability. In this paper we explore the fabrication and mechanical testing of natural fibre composites and this is part of an on going study at Strathclyde University and describes the fabrication of composites using natural fibre and styrene polyester resin. The properties of the synthetic resin can be varied by changing the catalysts concentration and flexural (three point bending) and single-edged notched bending (SENB) properties are reported at different concentrations of the catalyst
Electrolyte effects on poly (acrylic acid)-based aircraft de-icing fluids
Poly (acrylic acid) [PAA]-based aircraft de-icing fluids are widely used commercially but are known to be subject to the formation of insoluble gel particles within wing structures. In this study, the rheological effects of the sodium chloride, potassium formate, and calcium acetate with commercially used PAA-based fluids are reported across the temperature range of â15 to 15 °C. Calcium ions have the potential to create gel particles, reflected in the shifts in the viscosityâtemperature profile, while PAA aggregation is influenced by the concentrations and compositions of sodium and potassium salts in the water used for dilution. From the data presented, it is possible to create de-icing fluid formulations with the necessary rheological characteristics from stock solutions by dilution using available water sources, providing that the ion concentration is known