Improvement in the Power Output of a Reverse Electrodialysis System by the Addition of Poly(sodium 4-styrenesulfonate)

Salinity gradient energy generated by the contact between seawater and river water is one of the promising renewable energies. In the reverse electrodialysis (RED), salinity gradient energy is directly translated into the electricity. The representative problem is a large electrical resistance of river water or dilute solutions. The dilute solutions are poor electrically conductive. This results in a huge energy loss when an electrical current passes through it. In this study, sodium chloride (NaCl) or poly(sodium 4-styrenesulfonate) (NaPSS) was added to the dilute solutions to increase the conductivities and enhance the power outputs of the RED cells. When NaCl was added, the power output reached 11.4 ± 0.6 µW. On the other hand, when NaPSS was added, the power output increased up to 19.6 ± 0.6 µW

The Redox Potential Measurements for Heme Moieties in Variants of d-Fructose Dehydrogenase Based on Mediator-assisted Potentiometric Titration

The effect of mutation on the redox potentials (E degrees') of the heme moieties in the variants of D-fructose dehydrogenase (FDH) was investigated by mediated spectroelectrochemical titrations. The replacement of the axial ligand of heme from methionine to glutamine changes the E degrees' value more negatively than that of the corresponding heme moiety in the recombinant (native) FDH (rFDH). The determined E degrees' values of non-targeted heme moieties in the variants were also shifted in a negative direction from that in rFDH. Thus, enzyme modification changes E degrees' of the heme moieties in unmodified protein regions. (C) The Author(s) 2021. Published by ECSJ

Development Perspective of Bioelectrocatalysis-Based Biosensors

Bioelectrocatalysis provides the intrinsic catalytic functions of redox enzymes to nonspecific electrode reactions and is the most important and basic concept for electrochemical biosensors. This review starts by describing fundamental characteristics of bioelectrocatalytic reactions in mediated and direct electron transfer types from a theoretical viewpoint and summarizes amperometric biosensors based on multi-enzymatic cascades and for multianalyte detection. The review also introduces prospective aspects of two new concepts of biosensors: mass-transfer-controlled (pseudo)steady-state amperometry at microelectrodes with enhanced enzymatic activity without calibration curves and potentiometric coulometry at enzyme/mediator-immobilized biosensors for absolute determination

Direct electron transfer-type bioelectrocatalysis of redox enzymes at nanostructured electrodes

Direct electron transfer (DET)-type bioelectrocatalysis, which couples the electrode reactions and catalytic functions of redox enzymes without any redox mediator, is one of the most intriguing subjects that has been studied over the past few decades in the field of bioelectrochemistry. In order to realize the DET-type bioelectrocatalysis and improve the performance, nanostructures of the electrode surface have to be carefully tuned for each enzyme. In addition, enzymes can also be tuned by the protein engineering approach for the DET-type reaction. This review summarizes the recent progresses in this field of the research while considering the importance of nanostructure of electrodes as well as redox enzymes. This review also describes the basic concepts and theoretical aspects of DET-type bioelectrocatalysis, the significance of nanostructures as scaffolds for DET-type reactions, protein engineering approaches for DET-type reactions, and concepts and facts of bidirectional DET-type reactions from a cross-disciplinary viewpoint

Direct electron transfer-type bioelectrocatalysis by membrane-bound aldehyde dehydrogenase from Gluconobacter oxydans and cyanide effects on its bioelectrocatalytic properties

The bioelectrocatalytic properties of membrane-bound aldehyde dehydrogenase (AlDH) from Gluconobacter oxydans NBRC12528 were evaluated. AlDH exhibited direct electron transfer (DET)-type bioelectrocatalytic activity for acetaldehyde oxidation at several kinds of electrodes. The kinetic and thermodynamic parameters for bioelectrocatalytic acetaldehyde oxidation were estimated based on the partially random orientation model. Moreover, at the multi-walled carbon nanotube-modified electrode, the coordination of CN‾ to AlDH switched the direction of the DET-type bioelectrocatalysis to acetate reduction under acidic conditions. These phenomena were discussed from a thermodynamic viewpoint

Amperometric biosensor based on reductive H2O2 detection using pentacyanoferrate-bound polymer for creatinine determination.

Pentacyanoferrate-bound poly(1-vinylimidazole) (PVI[Fe(CN)5]) was selected as a mediator for amperometric creatinine determination based on the reductive H2O2 detection. Creatinine amidohydrolase (CNH), creatine amidohydrolase (CRH), sarcosine oxidase (SOD), peroxidase (POD), and PVI[Fe(CN)5] were crosslinked with poly(ethylene glycol) diglycidyl ether (PEGDGE) on a glassy carbon (GC) electrode for a creatinine biosensor fabrication. Reduction current was monitored at −0.1 V in the presence of creatinine and O2. It is revealed that PVI[Fe(CN)5] is suitable as a mediator for a bioelectrocatalytic reaction of POD, since PVI[Fe(CN)5] neither reacts with reactants nor works as an electron acceptor of SOD. The amounts of PVI[Fe(CN)5], PEGDGE, and enzymes were optimized toward creatinine detection. Nafion as a protecting film successfully prevented the enzyme layer from interferences. The detection limit and linear range in creatinine determination were 12 μM and 12–500 μM (R[2]= 0.993), respectively, and the sensitivity was 11 mA cm[−2] M[−1], which is applicable for urine creatinine tests. The results of the creatinine determination for four urine samples measured with this proposed method were compared with Jaffe method, and a good correlation was obtained between the results

Application of the powder of porous titanium carbide ceramics to a reusable adsorbent for environmental pollutants

The aim of this study is to investigate the utilization of the powder of porous titanium carbide (TiC) ceramics as a novel adsorbent or a material for solid-phase extraction (SPE). The adsorption and elution of inorganic and organic pollutants, Pb(II), 2,4,6-trichlorophenol (TCP), perfluorooctane sulfonate (PFOS), and perfluorooctanoic acid (PFOA), to the material were evaluated. The cartridge packed with TiC ceramics powder was used for the extraction test of pollutants. The solution containing pollutants at 1.0 mu g mL(-1) was passed through the TiC cartridge, and the substances were almost quantitatively removed. Furthermore, the pollutants retained in the cartridge were eluted with 3 N HCl for Pb(II) and with methanol for organic pollutants. The recoveries of pollutants were over 80%. In addition, we used the TiC cartridge for the solid-phase extraction of water samples (500 mL each of the distilled water and the river water) by adding pollutants at determined concentrations. Every pollutant was adsorbed almost quantitatively, and eluted by 3 N HCl or methanol. From these results, we concluded that the powder of porous TiC ceramics is a useful reusable adsorbent for the water cleanup and solid-phase extraction.ArticleJOURNAL OF HAZARDOUS MATERIALS. 185(2-3):725-731 (2011)journal articl

Role of a non-ionic surfactant in direct electron transfer-type bioelectrocatalysis by fructose dehydrogenase

A heterotrimeric membrane-bound fructose dehydrogenase (FDH) from Gluconobacter japonicus NBRC3260 contains FAD in subunit I and three heme C moieties in subunit II as the redox centers, and is one of the direct electron transfer (DET)-type redox enzymes. FDH-catalyzed current density of fructose oxidation at hydrophilic mercaptoethanol (MEtOH)-modified Au electrode is much larger than that at hydrophobic mercaptoethane (MEtn)-modified Au electrode. Addition of a non-ionic surfactant Triton® X-100 (1%) completely quenches the catalytic current at the MEtn-modified Au electrode, while only small competitive effect is observed at the MEtOH-modified Au electrode. Quartz crystal microbalance measurements support the adsorption of FDH and Triton® X-100 on both of the modified electrodes. We propose a model to explain the phenomenon as follows. The surfactant forms a monolayer on the hydrophobic MEtn-modified electrode with strong hydrophobic interaction, and FDH adsorbs on the surface of the surfactant monolayer. The monolayer inhibits the electron transfer from FDH to the electrode. On the other hand, the surfactant forms a bilayer on the hydrophilic MEtOH-modified electrode. The interaction between the surfactant bilayer and the hydrophilic electrode is relatively weak so that FDH replaces the surfactant and is embedded in the bilayer to communicate electrochemically with the hydrophilic electrode

Mass Measurement of the Decaying Bino at the LHC

In some class of supersymmetric (SUSY) models, the neutral Wino becomes the lightest superparticle and the Bino decays into the Wino and standard-model particles. In such models, we show that the measurement of the Bino mass is possible if the short charged tracks (with the length of O(10 cm)) can be identified as a signal of the charged-Wino production. We pay particular attention to the anomaly-mediated SUSY-breaking (AMSB) model with a generic form of K\"ahler potential, in which only the gauginos are kinematically accessible superparticles to the LHC, and discuss the implication of the Bino mass measurement for the test of the AMSB model.Comment: 13 pages, 3 figures, 1 tabl