Large deformations of thin plates subjected to impulsive loading

Includes bibliographical references.The dynamic response of structures subjected to blast and impact loading has been obtained relatively simply using rigid-plastic or rigid-viscoplastic material idealisations. It is essential, however, that the predictions of these idealised theories should be checked against experimental results, and over the past twenty years several experimental studies have been carried out. This thesis describes a series of experiments on fully clamped Circular, square and rectangular steel plates. The final midpoint deflections measured were between 3 and 12 plate thicknesses: and the deflection time history was measured using a light interference technique. While the deflection-time history was being recorded. the impulse was simultaneously being measured by means of a ballistic pendulum upon which the plates were attached. The impulse was provided by sheet explosive which was arranged in such a way that the plate was subjected to a uniformly distributed impulse. In addition an extension of a mode approximation method, based on the assumption that membrane stresses predominate, is presented. This method assumes that the material behaviour can be modelled as rigid-viscoplastic. and that at any instant the shapes of the displacement and the velocity field are the same. Points on the plate surface were first assumed to displace perpendicular to the initial surface: this assumption was then relaxed to permit points to move perpendicular to the current surface. In both cases. the predicted transverse displacements agreed well with the experimental data. The predicted radial strain distribution exhibited trends similar to the experimental data in the case where lateral displacements were modelled

Experimental response of an optical sensor used to determine the moment of blast by sensing the flash of the explosion

The Council for Scientific and Industrial Research (CSIR) conducts research into the effect of underwater explosions on maritime structures and equipment. One of the parameters that are required to be measured to a large degree of accuracy is the shock wave velocity in close proximity (10 - 120 charge radii) of the explosion, without having to revert to the streak photography method. This distance is in the region where the near field crosses over to the far field, and it would be expected that the distance-time curve would not be linear. The streak photography method produces accuracy in the very near field of the explosion, but is not recommended for accurate measurements at distances beyond 20 charge radii. We investigated the response of an optical sensor constructed to measure the light flash of an underwater blast to determine the moment of explosion. By measurement of the time taken between this moment and the time when the shock wave reaches the pressure sensors, accurate measurements of the distance-time history (and hence shock wave velocity) could be calculated. Twelve general purpose phototransistors were used in a parallel configuration to enhance the sensitivity of the sensor. These transistors were connected directly to a conditioning amplifier which formed the interface between the transistors and the data acquisition equipment. The results that were obtained confirmed that the light intensity of the flash of the explosion increased to a maximum within several microseconds. Measurements of the average velocity of the shock wave propagation, based on the flash measurement as a marker, correlated to within 0.1%, meaning that this method of marking the moment of explosion to within several microseconds had been successful. This method can therefore be used in similar underwater blast measurement applications when a measurement marker of the moment of explosion is required

Thermodynamic optimization tools for power tracking in a multistage concentrated solar power Rankine plant

Abstract: The object of the study is to present a method of thermodynamic optimization of power generating plants, in a mode that consolidates and simplifies the analysis of data on heat-work interaction of the plant components. The optimization scheme identifies the technical and process parameters that can improve the thermodynamic performance of the plant with respect to an objective variable, and further, the required thermodynamic measures necessary to improve the operating condition of the plant. Simple but effective tools are used to evaluate the optimal and suboptimal power generating capacities vis-à-vis the fundamental variables—namely, the thermodynamic quantity ratio (TQR) and the power-energy quantity ratio (PQR)—without routing optimization procedures. Beyond the optimal value of the objective variable, the power generation capacity of the plant is affected. The determination of the optimal value of the objective variable can also be approached by computerization; for fixed prescriptions of the boiler, superheater, and turbine parameters, variables such as boiler pressure and temperature can be optimally selected. DOI: 10.1061/(ASCE)EY.1943-7897.0000367. © 2016 American Society of Civil Engineers

Perforated Plates as Passive Mitigation Systems

This paper presents the results of tests on fully-clamped circular plates subjected to blastloading directed down a tube. Four series of tests were performed. In one set of experiments,the blast wave was allowed to progress unhindered down the tube to impinge upon the plate,and in the other tests, perforated plates were placed in the path of the blast wave to hinderprogression down the tube, disrupting the blast and absorbing some of the kinetic energy.Results of the tests indicate that the perforated plates can be used as a form of passive mitigation

A study on the response of single and double circular plates subjected to localised blast loading

The response of single and double layered steel plates to localised air-blast loading was examined. Two configurations, both comprising fully clamped circular plates with a 200 mm exposed diameter, were considered: 4mm thick single and (2+2) mm double layered plates. The localised air-blast loading was applied by centrally detonating discs of PE4 plastic explosive. Similar failure modes were evident in the single and double plate configurations, namely, Mode I (large inelastic deformation) and Mode II (capping failure along with deformation) responses. The double plates exhibited larger midpoint deflections than the single plates, and partial tearing of the front plate in the double plates was observed at a lower impulse than in the single plates. However, complete capping of both plates in the double plate configuration occurred at the same charge mass as for the single plates, implying that both configurations offer equivalent protection from capping failure as a result of this type of localised blast loading. A metallographic study of the deformed and torn plate regions did not reveal any phase transformation in the steel. It was also found that the 2 mm thick plates exhibited larger increases in grain size than the 4 mm thick plates

Application of X-ray micro-computed tomography on high-speed cavitating diesel fuel flows

The flow inside a purpose built enlarged single-orifice nozzle replica is quantified using time-averaged X-ray micro-computed tomography (micro-CT) and high-speed shadowgraphy. Results have been obtained at Reynolds and cavitation numbers similar to those of real-size injectors. Good agreement for the cavitation extent inside the orifice is found between the micro-CT and the corresponding temporal mean 2D cavitation image, as captured by the high-speed camera. However, the internal 3D structure of the developing cavitation cloud reveals a hollow vapour cloud ring formed at the hole entrance and extending only at the lower part of the hole due to the asymmetric flow entry. Moreover, the cavitation volume fraction exhibits a significant gradient along the orifice volume. The cavitation number and the needle valve lift seem to be the most influential operating parameters, while the Reynolds number seems to have only small effect for the range of values tested. Overall, the study demonstrates that use of micro-CT can be a reliable tool for cavitation in nozzle orifices operating under nominal steady-state conditions

Experimental measurement of specific impulse distribution and transient deformation of plates subjected to near-field explosive blasts

The shock wave generated from a high explosive detonation can cause significant damage to any objects that it encounters, particularly those objects located close to the source of the explosion. Understanding blast wave development and accurately quantifying its effect on structural systems remains a considerable challenge to the scientific community. This paper presents a comprehensive experimental study into the loading acting on, and subsequent deformation of, targets subjected to near-field explosive detonations. Two experimental test series were conducted at the University of Sheffield (UoS), UK, and the University of Cape Town (UCT), South Africa, where blast load distributions using Hopkinson pressure bars and dynamic target deflections using digital image correlation were measured respectively. It is shown through conservation of momentum and Hopkinson-Cranz scaling that initial plate velocity profiles are directly proportional to the imparted impulse distribution, and that spatial variations in loading as a result of surface instabilities in the expanding detonation product cloud are significant enough to influence the transient displacement profile of a blast loaded plate

Development of a new assessment tool for cervical myelopathy using hand-tracking sensor: Part 1: validity and reliability

Purpose To assess the reliability and validity of a hand motion sensor, Leap Motion Controller (LMC), in the 15-s hand grip-and-release test, as compared against human inspection of an external digital camera recording. Methods Fifty healthy participants were asked to fully grip-and-release their dominant hand as rapidly as possible for two trials with a 10-min rest in-between, while wearing a non-metal wrist splint. Each test lasted for 15 s, and a digital camera was used to film the anterolateral side of the hand on the first test. Three assessors counted the frequency of grip-and-release (G-R) cycles independently and in a blinded fashion. The average mean of the three was compared with that measured by LMC using the Bland–Altman method. Test–retest reliability was examined by comparing the two 15-s tests. Results The mean number of G-R cycles recorded was: 47.8 ± 6.4 (test 1, video observer); 47.7 ± 6.5 (test 1, LMC); and 50.2 ± 6.5 (test 2, LMC). Bland–Altman indicated good agreement, with a low bias (0.15 cycles) and narrow limits of agreement. The ICC showed high inter-rater agreement and the coefficient of repeatability for the number of cycles was ±5.393, with a mean bias of 3.63. Conclusions LMC appears to be valid and reliable in the 15-s grip-and-release test. This serves as a first step towards the development of an objective myelopathy assessment device and platform for the assessment of neuromotor hand function in general. Further assessment in a clinical setting and to gauge healthy benchmark values is warranted