Addressing Criticality in Rare Earth Elements via Permanent Magnets Recycling

Rare earth elements (REEs) are critical for many advanced technologies and are faced with potential supply disruptions. Recycling of permanent magnets (PMs) can be good sources for REEs which can help minimize global dependence on freshly mined REEs, but PMs are rarely recycled. Recycling of PMs has been discussed with respect to improving REEs resource sustainability. Some challenges to be addressed in order to establish industrially deployable technologies for PMs recycling have also been discussed, including profitability, energy efficiency and environmental impacts. Key considerations for promoting circular economy via PMs recycling is proposed with the focus on deciding the target points in the supply chain at which the recycled products will be inserted. Important technical considerations for recycling different forms of waste PMs, including swarfs, slags, shredded and intact hard disk drives magnets, have been presented. The aspects of circular economy considered include reusing magnets, remanufacturing magnets and recovering of REEs from waste PMs

Barkhausen spectroscopy: Non-destructive characterization of magnetic materials as a function of depth

In this study, we conceptually divided a ferromagnetic specimen into layers along its depth. For each layer, we derived a non-linear integral equation that describes the attenuation with frequency and distance of magnetic Barkhausen emissions coming from that layer. We postulate that the Barkhausen spectrum measured at the surface by an induction coil can be expressed as the sum of the individual layer spectra. We show how a non-linear least squares algorithm can be used to recover the properties in individual layers. These are related to stress using an extension to the theory of ferromagnetic hysteresis. We found that the quality of the fit is influenced by the sensitivity of the ferromagnetic material to strain, as well as by the sensor-specimen coupling. The proposed method can be used for the non-destructive characterization of stress as a function of depth in magnetic materials

A model for the Barkhausen frequency spectrum as a function of applied stress

We derive a two parameter multi-exponential model to describe the frequency spectrum ofBarkhausen noise in bulk steel under high excitation rates and applied tensile stress. We show how the amplitude and shape of the frequency spectrum depend on two directly measurable quantities, Barkhausen voltage and effective magnetic permeability, respectively, and how these change with stress. By incorporating frequency and depth dependence components into our model, we provide a framework for identifying stress variations along depth, which can be used for the purposes of non-destructive characterization

Ultrahigh Sensitivity of Anomalous Hall Effect Sensor Based on Cr-Doped Bi2Te3 Topological Insulator Thin Films

Anomalous Hall effect (AHE) was recently discovered in magnetic element-doped topological insulators (TIs), which promises low power consumption and high efficiency spintronics and electronics. This discovery broadens the family of Hall sensors. In this paper, AHE sensors based on Cr-doped Bi2Te3 topological insulator thin films are studied with two thicknesses (15 and 65 nm). It is found, in both cases, that ultrahigh Hall sensitivity can be obtained in Cr-doped Bi2Te3. Hall sensitivity reaches 1666 Ω/T in the sensor with the 15 nm TI thin film, which is higher than that of the conventional semiconductor HE sensor. The AHE of 65 nm sensors is even stronger, which causes the sensitivity increasing to 2620 Ω/T. Furthermore, after comparing Cr-doped Bi2Te3 with the previously studied Mn-doped Bi2Te3 TI Hall sensor, the sensitivity of the present AHE sensor shows about 60 times higher in 65 nm sensors. The implementation of AHE sensors based on a magnetic-doped TI thin film indicates that the TIs are good candidates for ultrasensitive AHE sensors

Microstructure and Magnetic Properties of Grain Refined Pr2Co14B Melt-Spun Ribbons

The correlation between the grain refining effect of TiC on the microstructure of Pr2Co14B melt-spun ribbons and the magnetic properties is presented in this study. TiC enabled greater control of microstructure both in the as-spun and heat treated Pr2Co14B, compared with the material without TiC. As a result, coercivity of the sample with TiC was nearly twice that of the sample without TiC. In addition to Pr2Co14B, two other phases were found in the sample with TiC: one rich in Co and the other having a composition near PrCo2. TiC was found near the grain boundaries and at triple junctions. Also no Ti or C was found in the matrix phase indicating extreme low solubility of the elements when both are present with Pr2Co14B. As expected, both the samples with and without TiC have similar anisotropy field but the presence of room temperature non-ferromagnetic phases (TiC and PrCo2), caused a small decrease in magnetization of the sample with TiC although the romance of the isotropic materials were comparable

Structural, magnetic, and magnetoelastic properties of magnesium substituted cobalt ferrite

The effects of substituting Mg on the structural, magnetic, and magnetostrictive properties ofcobalt ferrite have been investigated. Comparable values of lattice parameter were obtained for the Mg-substituted samples. Saturation magnetization continuously decreased with increase inMg concentration. Peak-to-peak magnetostriction amplitude and strain sensitivity had a similar dependence on Mg concentration