8 research outputs found

    Ultra-stiff large-area carpets of carbon nanotubes

    Get PDF
    Herewith, we report the influence of post-synthesis heat treatment (≤2350 °C and plasma temperatures) on the crystal structure, defect density, purity, alignment and dispersibility of free-standing large-area (several cm2) carpets of ultra-long (several mm) vertically aligned multi-wall carbon nanotubes (VA-MWCNTs). VA-MWCNTs were produced in large quantities (20–30 g per batch) using a semi-scaledup aerosol-assisted chemical vapour deposition (AACVD) setup. Electron and X-ray diffraction showed that the heat treatment at 2350 °C under inert atmosphere purifies, removes residual catalyst particles, and partially aligns adjacent single crystals (crystallites) in polycrystalline MWCNTs. The purification and improvement in the crystallites alignment within the MWCNTs resulted in reduced dispersibility of the VA-MWCNTs in liquid media. High-resolution microscopy revealed that the crystallinity is improved in scales of few tens of nanometres while the point defects remain largely unaffected. The heat treatment also had a marked benefit on the mechanical properties of the carpets. For the first time, we report compression moduli as high as 120 MPa for VA-MWCNT carpets, i.e. an order of magnitude higher than previously reported figures. The application of higher temperatures (arc-discharge plasma, ≥4000 °C) resulted in the formation of a novel graphite–matrix composite reinforced with CVD and arc-dischargelike carbon nanotubes

    Interferometry-based micropipette aspiration allows to study of the nanoscale dynamic mechanical behavior of biomaterials

    No full text
    A novel, interferometry-based approach to micropipette aspiration overcomes the spatial resolution limit of current methods, simplifies data retrieval, and enables the study of the dynamic mechanical behavior of biomembranes at the nanoscale

    Opto-mechanical lab-on-fibre seismic sensors detected the Norcia earthquake

    No full text
    We have designed and developed lab-on-fibre seismic sensors containing a micro-opto-mechanical cavity on the fibre tip. The mechanical cavity is designed as a double cantilever suspended on the fibre end facet and connected to a proof mass to tune its response. Ground acceleration leads to displacement of the cavity length, which in turn can be remotely detected using an interferometric interrogation technique. After the sensors characterization, an experimental validation was conducted at the Italian National Institute of Geophysics and Volcanology (INGV), which is responsible for seismic surveillance over the Italian country. The fabricated sensors have been continuously used for long periods to demonstrate their effectiveness as seismic accelerometer sensors. During the tests, fibre optic seismic accelerometers clearly detected the seismic sequence that culminated in the severe Mw6.5 Norcia earthquake that struck central Italy on October 30, 2016. The seismic data provided by the optical sensors were analysed by specialists at the INGV. The wave traces were compared with state-of-the-art traditional sensors typically incorporated into the INGV seismic networks. The comparison verifies the high fidelity of the optical sensors in seismic wave detection, indicating their suitability for a novel class of seismic sensors to be employed in practical scenarios.Publishedid 66801IT. Reti di monitoraggioJCR Journa

    Interferometry-based micropipette aspiration allows to study of the nanoscale dynamic mechanical behavior of biomaterials

    No full text
    A novel, interferometry-based approach to micropipette aspiration overcomes the spatial resolution limit of current methods, simplifies data retrieval, and enables the study of the dynamic mechanical behavior of biomembranes at the nanoscale

    Optical interferometry based micropipette aspiration provides real-time sub-nanometer spatial resolution

    Get PDF
    Micropipette aspiration (MPA) is an essential tool in mechanobiology; however, its potential is far from fully exploited. The traditional MPA technique has limited temporal and spatial resolution and requires extensive post processing to obtain the mechanical fingerprints of samples. Here, we develop a MPA system that measures pressure and displacement in real time with sub-nanometer resolution thanks to an interferometric readout. This highly sensitive MPA system enables studying the nanoscale behavior of soft biomaterials under tension and their frequency-dependent viscoelastic response

    Platelet control of fibrin distribution and microelasticity in thrombus formation under flow

    Get PDF
    Objective—Platelet- and fibrin-dependent thrombus formation is regulated by blood flow and exposure of collagen and tissue factor. However, interactions between these blood-borne and vascular components are not well understood. Approach and Results—Here, we developed a method to assess whole-blood thrombus formation on microspots with defined amounts of collagen and tissue factor, allowing determination of the mechanical properties and intrathrombus composition. Confining the collagen content resulted in diminished platelet deposition and fibrin formation at high shear flow conditions, but this effect was compensated by a larger thrombus size and increased accumulation of fibrin in the luminal regions of the thrombi at the expense of the base regions. These thrombi were more dependent on tissue factor–triggered thrombin generation. Microforce nanoindentation analysis revealed a significantly increased microelasticity of thrombi with luminal-oriented fibrin. At a low shear rate, fibrin fibers tended to luminally cover the thrombi, again resulting in a higher microelasticity. Studies with blood from patients with distinct hemostatic insufficiencies indicated an impairment in the formation of a platelet–fibrin thrombus in the cases of dilutional coagulopathy, thrombocytopenia, Scott syndrome, and hemophilia B. Conclusions—Taken together, our data indicate that (1) thrombin increases the platelet thrombus volume; (2) tissue factor drives the formation of fibrin outside of the platelet thrombus; (3) limitation of platelet adhesion redirects fibrin from bottom to top of the thrombus; (4) a lower shear rate promotes thrombus coverage with fibrin; (5) the fibrin distribution pattern determines thrombus microelasticity; and (6) the thrombus-forming process is reduced in patients with diverse hemostatic defects
    corecore