The ABC130 barrel module prototyping programme for the ATLAS strip tracker

For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100 % silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-25) and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests.Comment: 82 pages, 66 figure

First bulk and surface results for the ATLAS ITk stereo annulus sensors

A novel microstrip sensor geometry, the “stereo annulus”, has been developed for use in the end-cap of the ATLAS experiment’s strip tracker upgrade at the High-Luminosity Large Hadron Collider (HL- LHC). The radiation-hard, single-sided, ac-coupled, n + -in-p microstrip sensors are designed by the ITk Strip Sensor Collaboration and produced by Hamamatsu Photonics. The stereo annulus design has the potential to revolutionize the layout of end-cap microstrip trackers promising better tracking performance and more complete coverage than the contemporary configurations. These advantages are achieved by the union of equal length, radially oriented strips with a small stereo angle implemented directly into the sensor surface. The first-ever results for the stereo annulus geometry have been collected across several sites world- wide and are presented here. A number of full-size, unirradiated sensors were evaluated for their mechanical, bulk, and surface properties. The new device, the ATLAS12EC, is compared against its conventionally shaped predecessors, the ATLAS07 and ATLAS12, for realistic evaluation of the sensor design. The bulk character of the unirradiated sensors has been determined from IV curve, CV curve, and metrology studies. The leakage current and full depletion voltage characteristics have been obtained and compared with the strict specifications required by the next-generation tracker. Interstrip capacitance and resistance in the four segments of strips, each with equal length constituents and a constant angular pitch, have also been ascertained and are compared to expectations. Long-term leakage current stability tests under various humidity conditions have been conducted to investigate more closely the surface and edge processing. These also allow the determination of any high electric field gradients in the synthesis of stereo radial strips with a tracking coverage enhancing slim edge- width. The impact of the novel stereo annulus sensor geometry on the operation of the detector has been evaluated in these studies. The suitability of the optimized sensor shape for the ATLAS HL-LHC upgrade and future end-cap microstrip trackers will be discussed

First bulk and surface results for the ATLAS ITk Strip stereo annulus sensors

A novel microstrip sensor geometry, the stereo annulus, has been developed for use in the end-cap of the ATLAS experiment's strip tracker upgrade at the HL-LHC. Its first implementation is in the ATLAS12EC sensors a large-area, radiation-hard, single-sided, ac-coupled, \ninp design produced by the ITk Strip Sensor Collaboration and fabricated by Hamamatsu Photonics in early 2017. The results of the initial testing of two ATLAS12EC batches are presented here with a comparison to specification. The potential of the new sensor shape to reinvigorate endcap strip tracking is explained and its effects on sensor performance are isolated by comparing the bulk mechanical and electrical properties of the new sensor to the previous iteration of prototype, the conventional barrel ATLAS12A sensor. The surface properties of the new sensor are evaluated for full-size unirradiated sensors as well as for mini sensors unirradiated and irradiated with $p^{+}$ up to a fluence of $2.2 \times 10^{15}$\neqsq. The results show that the new stereo annulus ATLAS12EC sensors exhibit excellent performance and the expected irradiation evolution

The ABC130 barrel module prototyping programme for the ATLAS strip tracker

For the Phase-II Upgrade of the ATLAS Detector [1], its Inner Detector, consisting of silicon pixel, silicon strip and transition radiation sub-detectors, will be replaced with an all new 100% silicon tracker, composed of a pixel tracker at inner radii and a strip tracker at outer radii. The future ATLAS strip tracker will include 11,000 silicon sensor modules in the central region (barrel) and 7,000 modules in the forward region (end-caps), which are foreseen to be constructed over a period of 3.5 years. The construction of each module consists of a series of assembly and quality control steps, which were engineered to be identical for all production sites. In order to develop the tooling and procedures for assembly and testing of these modules, two series of major prototyping programs were conducted: an early program using readout chips designed using a 250 nm fabrication process (ABCN-250) [2,2] and a subsequent program using a follow-up chip set made using 130 nm processing (ABC130 and HCC130 chips). This second generation of readout chips was used for an extensive prototyping program that produced around 100 barrel-type modules and contributed significantly to the development of the final module layout. This paper gives an overview of the components used in ABC130 barrel modules, their assembly procedure and findings resulting from their tests