Limit of light coupling strength in solar cells

We introduce a limit for the strength of coupling light into the modes of solar cells. This limit depends on both a cell's thickness and its modal properties. For a cell with refractive index n and thickness d, we obtain a maximal coupling rate of 2c*sqrt(n^2-1)/d where c is speed of light. Our method can be used in the design of solar cells and in calculating their efficiency limits; besides, it can be applied to a broad variety of resonant phenomena and devices

Lightweight Carbon Fiber Mirrors for Solar Concentrator Applications

Lightweight parabolic mirrors for solar concentrators have been fabricated using carbon fiber reinforced polymer (CFRP) and a nanometer scale optical surface smoothing technique. The smoothing technique improved the surface roughness of the CFRP surface from ~3 {\mu}m root mean square (RMS) for as-cast to ~5 nm RMS after smoothing. The surfaces were then coated with metal, which retained the sub-wavelength surface roughness, to produce a high-quality specular reflector. The mirrors were tested in an 11x geometrical concentrator configuration and achieved an optical efficiency of 78% under an AM0 solar simulator. With further development, lightweight CFRP mirrors will enable dramatic improvements in the specific power, power per unit mass, achievable for concentrated photovoltaics in space.Comment: IEEE Photovoltaic Specialist Conference (PVSC), DC, USA, 201

Extremely broadband ultralight thermally emissive metasurfaces

We report the design, fabrication and characterization of ultralight highly emissive metaphotonic structures with record-low mass/area that emit thermal radiation efficiently over a broad spectral (2 to 35 microns) and angular (0-60 degrees) range. The structures comprise one to three pairs of alternating nanometer-scale metallic and dielectric layers, and have measured effective 300 K hemispherical emissivities of 0.7 to 0.9. To our knowledge, these structures, which are all subwavelength in thickness are the lightest reported metasurfaces with comparable infrared emissivity. The superior optical properties, together with their mechanical flexibility, low outgassing, and low areal mass, suggest that these metasurfaces are candidates for thermal management in applications demanding of ultralight flexible structures, including aerospace applications, ultralight photovoltaics, lightweight flexible electronics, and textiles for thermal insulation

Extremely broadband ultralight thermally emissive metasurfaces

We report the design, fabrication and characterization of ultralight highly emissive metaphotonic structures with record-low mass/area that emit thermal radiation efficiently over a broad spectral (2 to 35 microns) and angular (0–60°) range. The structures comprise one to three pairs of alternating nanometer-scale metallic and dielectric layers, and have measured effective 300 K hemispherical emissivities of 0.7 to 0.9. To our knowledge, these structures, which are all subwavelength in thickness are the lightest reported metasurfaces with comparable infrared emissivity. The superior optical properties, together with their mechanical flexibility, low outgassing, and low areal mass, suggest that these metasurfaces are candidates for thermal management in applications demanding of ultralight flexible structures, including aerospace applications, ultralight photovoltaics, lightweight flexible electronics, and textiles for thermal insulation

Enhanced light trapping in realistic thin film solar cells using one-dimensional gratings

Finding the optimal structure to enhance light trapping in thin film silicon solar cells has attracted much attention in the previous decades. However, because of problems in integrating theory and experiment, there are only few comprehensive contributions that provide guidelines for the optimal design of such structures. In this work, a realistic thin film solar cell with almost conformal layers based on a one-dimensional metallic grating back-reflector is investigated through experiment and theory. The external quantum efficiency of the cell is obtained with the aid of both theory and experiment for different angles of incidence and in both polarizations to validate the computational method and to show the impact of guided mode excitation. Different substrate shapes that are compatible with solar cell fabrication are then considered and the effect of geometrical parameters on the short circuit current density of the device is investigated. Calculations show that among the investigated shapes, trinagular gratings with a very sharp slope in one side, so called sawtooth gratings, are the most promising one-dimensional grating for light trapping. Furthermore, the role of material property is discussed specifically in the back-reflector by simulating aluminum and silver back-reflectors. It is shown that the blue response of the solar cells is similar almost regardless of the back-reflector material but their red response is viable to change due to variation in resonant properties of the structure

Light-trapping in the near field: the case for plasmonic thin-film solar cells

We study the plasmonic and the non-plasmonic regimes of operation of a thin-film amorphous-silicon solar cell. By rigorous calculation, we discuss the impact of the cell geometry on the nature of its optical resonances

Lightweight Carbon Fiber Mirrors for Solar Concentrator Applications

Lightweight parabolic mirrors for solar concentrators have been fabricated using carbon fiber reinforced polymer (CFRP) and a nanometer scale optical surface smoothing technique. The smoothing technique improved the surface roughness of the CFRP surface from ~3 μm root mean square (RMS) for as-cast to ~5 nm RMS after smoothing. The surfaces were then coated with metal, which retained the sub-wavelength surface roughness, to produce a high-quality specular reflector. The mirrors were tested in an 11x geometrical concentrator configuration and achieved an optical efficiency of 78% under an AM0 solar simulator. With further development, lightweight CFRP mirrors will enable dramatic improvements in the specific power, power per unit mass, achievable for concentrated photovoltaics in space

Extremely broadband ultralight thermally-emissive optical coatings

We report the design, fabrication, and characterization of ultralight highly emissive structures with a record-low mass per area that emit thermal radiation efficiently over a broad spectral (2 to 30 microns) and angular (0–60°) range. The structures comprise one to three pairs of alternating metallic and dielectric thin films and have measured effective 300 K hemispherical emissivity of 0.7 to 0.9 (inferred from angular measurements which cover a bandwidth corresponding to 88% of 300K blackbody power). To our knowledge, these micron-scale-thickness structures, are the lightest reported optical coatings with comparable infrared emissivity. The superior optical properties, together with their mechanical flexibility, low outgassing, and low areal mass, suggest that these coatings are candidates for thermal management in applications demanding of ultralight flexible structures, including aerospace applications, ultralight photovoltaics, lightweight flexible electronics, and textiles for thermal insulation