Wave overtopping at near-vertical seawalls: Influence of foreshore evolution during storms

This work presents the results of an investigation on how wave overtopping at a near-vertical seawall at the back of a sandy foreshore is influenced by sequences of erosive storms. The experiments were carried out in the Large Wave Flume (GWK) at Leibniz University, Hannover (Germany). The tested layout consisted of a near-vertical 10/1 seawall and a sandy foreshore with an initial 1/15 slope. Three sequences of idealised erosive storms were simulated. Within each storm both the incident wave conditions and still water level were varied in time to represent high and low tide conditions. Each sequence started from a 1/15 configuration and the beach was not restored in between storms. The measurements included waves, beach profile, wave overtopping volumes. The profile of the beach was measured after each sea state tested. Wave overtopping at each stage of the tested storms was significantly influenced by bed changes. This was linked to the measured evolution of the beach. Measurements showed that a barred profile developed quickly at the start of each sequence, and scour developed at the toe of the structure during high water level conditions, while accretion or partial backfilling developed during low water level conditions. Due to these processes, the position of a sea state in the tested sequence is shown to be an important factor in determining the wave overtopping volume. Remarkably, when a weaker idealised storm followed a more energetic one, nearly the same level of overtopping was recorded. This is explained by the foreshore erosion, leading to increased water depths and wave heights at the toe of the structure. This finding allows to quantify and to explain the variability of wave overtopping in storms following one another at intervals shorter than the recovery time of the foreshore

Wave overtopping at near-vertical seawalls: Influence of foreshore evolution during storms

This work presents the results of an investigation on how wave overtopping at a near-vertical seawall at the back of a sandy foreshore is influenced by sequences of erosive storms. The experiments were carried out in the Large Wave Flume (GWK) at Leibniz University, Hannover (Germany). The tested layout consisted of a near-vertical seawall and a sandy foreshore with an initial slope. Three sequences of idealised erosive storms were simulated. Within each storm both the incident wave conditions and still water level were varied in time to represent high and low tide conditions. Each sequence started from a configuration and the beach was not restored in between storms. The measurements included waves, beach profile, wave overtopping volumes. The profile of the beach was measured after each sea state tested. Wave overtopping at each stage of the tested storms was significantly influenced by bed changes. This was linked to the measured evolution of the beach. Measurements showed that a barred profile developed quickly at the start of each sequence, and scour developed at the toe of the structure during high water level conditions, while accretion or partial backfilling developed during low water level conditions. Due to these processes, the position of a sea state in the tested sequence is shown to be an important factor in determining the wave overtopping volume. Remarkably, when a weaker idealised storm followed a more energetic one, nearly the same level of overtopping was recorded. This is explained by the foreshore erosion, leading to increased water depths and wave heights at the toe of the structure. This finding allows to quantify and to explain the variability of wave overtopping in storms following one another at intervals shorter than the recovery time of the foreshore

Large scale tests on foreshore evolution during storm sequences and the performance of a nearly vertical structure

This work presents the results of an experimental investigation on the effects of a sequence of storms on wave overtopping at a nearly vertical battered seawall at the back of a sandy foreshore. The experiments were carried out in the Large Wave Flume (GWK) at Leibniz Universität Hannover (Germany), as part of the research project ICODEP (Impact of Changing fOreshore on flood DEfence Performance), within the European Union programme Hydralab+. The layout consisted of a 10/1 battered seawall and a natural sandy foreshore with an initial 1:15 slope. The beach sand had a nominal diameter of 0.30 mm. Three storm sequences were simulated, where each consisted of three individual storms. Each storm was divided into six steps in which the wave conditions and still water level were varied to represent the peak of an actual storm. The six sea states were based on a JONSWAP spectral shape, with wave heights roughly between 0.6 m and 0.8 m. Two still water levels were tested. For the central two steps the level was such that the freeboard was only 0.14 m and almost all waves were overtopping. In the remaining steps low still water levels were employed, leaving a narrow swash zone. Two storm profiles were considered, the first one with a lower level of energy and the second one with a higher one. These were combined in the three different sequences. All the tested wave conditions were designed to be erosive for the beach, with no recovery in between. Each sequence started from a plain beach configuration and the beach was not restored in between storms. The measurements included waves, pressure and forces, sediment concentrations and flow velocity together with overtopping. The profile of the beach was measured after each sea state tested