50 research outputs found
Microstructural, texture, plastic anisotropy and superplasticity development of ZK60 alloy during equal channel angular extrusion processing
In this study, equal channel angular pressing (ECAP) was exploited to refine the grain size of a ZK60 magnesium alloy in multi-processing steps, namely at temperatures of 250˚C, 200˚C and 150˚C, producing an ultrafine-grained (UFG) structure. The microstructural development and texture evolution during ECAP were systemically investigated by electron backscattered diffraction (EBSD) analysis. The microstructure of the ECAP processed alloy was remarkably refined to an average grain size of 600 nm. During ECAP process the original fiber texture of the as-extruded alloy was gradually weakened and eventually replaced by a stronger texture component coinciding with ECAP shear plane. The ECAP processed material showed a proper balance of tensile as well as compression strength and tensile ductility at room temperature. Yield strength of 273 and 253 MPa in tension and compression, respectively, ultimate tensile strength of 298 MPa and fracture elongation of about 30% were obtained in the UFG alloy. A transition from ductile–brittle to ductile fracture consisting of very fine and equiaxed dimples was also found in the ECAP processed material. Compared to the as-received alloy, a combination of grain refinement and texture development in the UFG alloy gave rise to a notable reduction in mechanical asymmetric behavior at room temperature. The superplastic behavior of the as-extruded and ECAP processed alloy was also investigated at 200˚C with strain rate of 1.0×10-3 s-1.
The concurrent effect of grain boundary sliding and favorable basal texture in the UFG alloy led to an achievement of elongation value of about 300% while, under similar testing conditions, the elongation of about 140% was obtained in the as-extruded alloy
Tailoring the mechanical and degradation performance of Mg-2.0Zn-0.5Ca-0.4Mn alloy through microstructure design
A novel Mg-2.0Zn-0.5Ca-0.4Mn alloy has been formulated and processed through melt spinning and hot extrusion to enhance its mechanical and degradation properties. Microstructural characterization of rapidly solidified alloy ribbons consolidated by extrusion revealed a fine and fully recrystallized microstructure with average size of 4 µm. The conventionally extruded alloy consisted of several course second-phase strips as coarse as 100 µm, while the extrusion-consolidated ribbons were devoid of any second phases larger than 100 nm. Rapid solidification followed by extrusion processing resulted in significantly randomized texture where the majority of the basal planes were tilted toward transverse and extrusion directions. Such a weak texture resulted in higher activity of basal planes and thereby considerably improved the fracture elongation from 4% to 19%, while retaining relatively high tensile strength of 294 MPa. In addition to high strength and ductility due to the reduced activity of deformation twining during compression, the extrusion-consolidated alloy ribbons showed lower yielding asymmetric ratio than that measured for the conventionally extruded alloy (1.25 versus 1.61). Electrochemical measurements and immersion tests indicated that application of rapid solidification followed by extrusion remarkably reduced the corrosion rate from 2.49 mm/year to 0.37 mm/year due to recrystallization completion and suppression of coarse second-phase formation
Towards revealing key factors in mechanical instability of bioabsorbable Zn-based alloys for intended vascular stenting
Zn-based alloys are recognized as promising bioabsorbable materials for cardiovascular stents, due to their biocompatibility and favorable degradability as compared to Mg. However, both low strength and intrinsic mechanical instability arising from a strong strain rate sensitivity and strain softening behavior make development of Zn alloys challenging for stent applications. In this study, we developed binary Zn-4.0Ag and ternary Zn-4.0Ag-xMn (where x = 0.2–0.6wt%) alloys. An experimental methodology was designed by cold working followed by a thermal treatment on extruded alloys, through which the effects of the grain size and precipitates could be thoroughly investigated. Microstructural observations revealed a significant grain refinement during wire drawing, leading to an ultrafine-grained (UFG) structure with a size of 700 nm and 200 nm for the Zn-4.0Ag and Zn-4.0Ag-0.6Mn, respectively. Mn showed a powerful grain refining effect, as it promoted the dynamic recrystallization. Furthermore, cold working resulted in dynamic precipitation of AgZn3 particles, distributing throughout the Zn matrix. Such precipitates triggered mechanical degradation through an activation of Zn/AgZn3 boundary sliding, reducing the tensile strength by 74% and 57% for Zn-4.0Ag and Zn-4.0Ag-0.6Mn, respectively. The observed precipitation softening caused a strong strain rate sensitivity in cold drawn alloys. Short-time annealing significantly mitigated the mechanical instability by reducing the AgZn3 fraction. The ternary alloy wire showed superior microstructural stability relative to its Mn-free counterpart due to the pinning effect of Mn-rich particles on the grain boundaries. Eventually, a shift of the corrosion regime from localized to more uniform was observed after the heat treatment, mainly due to the dissolution of AgZn3 precipitates.
Statement of Significance
Owing to its promising biodegradability, zinc has been recognized as a potential biodegradable material for stenting applications. However, Zn's poor strength alongside intrinsic mechanical instability have propelled researchers to search for Zn alloys with improved mechanical properties. Although extensive researches have been conducted to satisfy the mentioned concerns, no Zn-based alloys with stabilized mechanical properties have yet been reported. In this work, the mechanical properties and stability of the Zn-Ag-based alloys were systematically evaluated as a function of microstructural features. We found that the microstructure design in Zn alloys can be used to find an effective strategy to not only improve the strength and suppress the mechanical instability but also to minimize any damage by augmenting the corrosion uniformity
Ultrafine grained plates of Al-Mg-Si alloy obtained by Incremental Equal Channel Angular Pressing : microstructure and mechanical properties
In this study, an Al-Mg-Si alloy was processed using via Incremental Equal Channel Angular Pressing (I-ECAP) in order to obtain homogenous, ultrafine grained plates with low anisotropy of the mechanical properties. This was the first attempt to process an Al-Mg-Si alloy using this technique. Samples in the form of 3 mm-thick square plates were subjected to I-ECAP with the 90˚ rotation around the axis normal to the surface of the plate between passes. Samples were investigated first in their initial state, then after a single pass of I-ECAP and finally after four such passes. Analyses of the microstructure and mechanical properties demonstrated that the I-ECAP method can be successfully applied in Al-Mg-Si alloys. The average grain size decreased from 15 - 19 µm in the initial state to below 1 µm after four I-ECAP passes. The fraction of high angle grain boundaries in the sample subjected to four I-ECAP passes lay within 53-57 % depending on the examined plane. The mechanism of grain refinement in Al-Mg-Si alloy was found to be distinctly different from that in pure aluminium with the grain rotation being more prominent than the grain subdivision, which was attributed to lower stacking fault energy and the reduced mobility of dislocations in the alloy. The ultimate tensile strength increased more than twice, whereas the yield strength - more than threefold. Additionally, the plates processed by I-ECAP exhibited low anisotropy of mechanical properties (in plane and across the thickness) in comparison to other SPD processing methods, which makes them attractive for further processing and applications
Ultrafine-Grained Plates of Al-Mg-Si Alloy Obtained by Incremental Equal Channel Angular Pressing: Microstructure and Mechanical Properties
Fabrication, mechanical properties and in vitro degradation behavior of newly developed ZnAg alloys for degradable implant applications
Zn and Zn-based alloys have been recognized as highly promising biodegradable materials for orthopedic implants and cardiovascular stents, due to their proved biocompatibility and, more importantly, lower corrosion rates compared to Mg alloys. However, pure Zn has poor mechanical properties. In this study, Ag is used as a promising alloying element to improve the mechanical properties of the Zn matrix as well as its biocompatibility and antibacterial properties. Accordingly, we design three ZnAg alloys with Ag content ranging from 2.5 to 7.0wt% and investigate the influence of the Ag content on mechanical and corrosion behavior of the alloys. The alloys are developed by casting process and homogenized at 410°C for 6h and 12h, followed by hot extrusion at 250°C with extrusion ratio of 14:1. Degradation behavior is assessed by electrochemical and static immersion tests in Hank's modified solution. Microstructural analysis reveals that hot extrusion significantly reduces the grain size of the alloys. Zn-7.0%Ag alloy shows a reasonably equiaxed and considerably refined microstructure with mean grain size of 1.5μm. Tensile tests at room temperature suggest that increasing the Ag content steadily enhances the tensile strength, while it does not affect the tensile ductility significantly. Zn-7.0%Ag shows high yield strength and ultimate tensile strength of 236MPa and 287MPa, respectively, which is due to the grain refinement and high volume fraction of fine AgZn3 particles precipitating along the grain boundaries during the extrusion process. Among all these alloys, Zn-7.0%Ag displayed superplasticity over a wide range of strain rates (from 5×10(-4)s(-1) to 1.0×10(-2)s(-1)) providing the possibility of exploiting forming processes at rapid rates and/or even at lower temperatures. In addition, extruded alloys exhibit slightly faster degradation rate than pure Zn. X-ray diffraction results show the presence of ZnO and Zn(OH)2 on the degraded surfaces. Moreover, scanning electron microscopy imaging reveals that micro-galvanic corrosion is more pronounced on the alloys with higher Ag content due to the higher volume fraction of AgZn3 particles. [Abstract copyright: Copyright © 2017 Elsevier B.V. All rights reserved.