45 research outputs found
La5Ti2Cu1-xAgxS5O7 photocathodes operating at positive potentials during photoelectrochemical hydrogen evolution under irradiation of up to 710 nm
A photoelectrochemical (PEC) cell based on a series-connected photocathode and photoanode made of particulate semiconductors is a potentially scalable and inexpensive device for renewable solar hydrogen production via PEC water splitting without any external power supply. The realisation of such PEC devices hinges on the development of photoelectrodes that operate at a small applied voltage. In this study, solid solutions of La5Ti2CuS5O7 (LTC) and La5Ti2AgS5O7 (LTA) were synthesised, and their physical, optical, and PEC properties in the water splitting reaction were discussed. LTC and LTA formed a La5Ti2Cu1-xAgxS5O7 solid solution (LTC(1-x)A(x)) over the whole compositional range. The indirect bandgap energy of LTC(1-x)A(x) changed nonlinearly with respect to composition, attaining its minimum value (ca. 1.8 eV) at a composition of x approximate to 0.16. Photoelectrodes of Al-doped LTC(1-x)A(x) solid solution powder fabricated using the particle transfer method exhibited a photocathodic response regardless of the Ag content. 1% Al-LTC(0.9)A(0.1) photocathodes exhibited the best PEC properties in the hydrogen evolution reaction and yielded a hypothetical half-cell solar-to-hydrogen energy conversion efficiency of 0.25% at +0.6 V vs. RHE, three times higher than the previously reported 1% Sc-LTC. In addition, 1% Al-LTC(0.9)A(0.1) photocathodes were fairly stable at + 0.7 V vs. RHE without any protective modifications. Owing to the positive operational electrode potential of 1% Al-LTC(0.9)A(0.1), unassisted PEC water splitting was accomplished using series-connected photoelectrodes made of 1% Al-LTC(0.9)A(0.1) and BaTaO2N, particulate semiconductors with absorption edge wavelengths of 710 and 660 nm, respectively, at a Faradaic efficiency of unity and a solar-to-hydrogen energy conversion efficiency of approximately 0.1%.ArticleEnergy & Environmental Science.8(11):3354-3362(2015)journal articl
Recommended from our members
La5 Ti2 Cu0.9 Ag0.1 S5 O7 Modified with a Molecular Ni Catalyst for Photoelectrochemical H2 Generation.
The stable and efficient integration of molecular catalysts into p-type semiconductor materials is a contemporary challenge in photoelectrochemical fuel synthesis. Here, we report the combination of a phosphonated molecular Ni catalyst with a TiO2 -coated La5 Ti2 Cu0.9 Ag0.1 S5 O7 photocathode for visible light driven H2 production. This hybrid assembly provides a positive onset potential, large photocurrents, and high Faradaic yield for more than three hours. A decisive feature of the hybrid electrode is the TiO2 interlayer, which stabilizes the oxysulfide semiconductor and allows for robust attachment of the phosphonated molecular catalyst. This demonstration of an oxysulfide-molecular catalyst photocathode provides a novel platform for integrating molecular catalysts into photocathodes and the large photovoltage of the presented system makes it ideal for pairing with photoanodes.Japan Society for the Promotion of Science (JSPS); Christian Doppler Research Association (Austrian Federal Ministry of Science, Research and Economy and the National Foundation for Research, Technology and Development); OMV group; EPSRC, Grants-in-Aids for Scientific Research and for Young Scientists from JSP
An Al-doped SrTiO3 photocatalyst maintaining sunlight-driven overall water splitting activity for over 1000 h of constant illumination
Photocatalytic water splitting is a viable approach to the large-scale production of renewable solar hydrogen. The apparent quantum yield for this reaction has been improved, but the lifespan of photocatalysts functioning under sunlight at ambient pressure have rarely been examined, despite the critical importance of this factor in practical applications. Herein, we show that Al-doped SrTiO3 (SrTiO3: Al) loaded with a RhCrOx (rhodium chromium oxide) cocatalyst splits water with an apparent quantum yield greater than 50% at 365 nm. Moreover, following the photodeposition of CoOOH and TiO2, this material maintains 80% of its initial activity and a solar-to-hydrogen energy conversion efficiency greater than or equal to 0.3% over a span of 1300 h under constant illumination by simulated sunlight at ambient pressure. This result is attributed to reduced dissolution of Cr in the cocatalyst following the oxidative photodeposition of CoOOH. The photodeposition of TiO2 further improves the durability of this photocatalyst. This work demonstrates a concept that could allow the design of longterm, large-scale photocatalyst systems for practical sunlight-driven water splitting.ArticleCHEMICAL SCIENCE.10(11):3196-3201(2019)journal articl
Kinetic Assessment and Numerical Modeling of Photocatalytic Water Splitting toward Efficient Solar Hydrogen Production
Photocatalytic water splitting has been studied extensively as a promising technology for scalable and cost-efficient hydrogen production using solar energy. Although overall water splitting has been achieved under visible light irradiation, significant progress in reaction efficiencies at longer wavelengths is needed to enable practical solar energy conversion. This article reports recent advancements in kinetic investigation and numerical modeling of photocatalytic water splitting to understand problems with existing photocatalysts and develop strategies to boost the reaction efficiency. Kinetic investigation based on cocatalyst loading, light intensity, hydrogen/deuterium isotopes, and reaction temperature suggests that the majority of photoexcited carriers recombine before contributing to the water splitting reaction on the surface in most cases, and that improvement in semiconducting properties of photocatalysts by decreasing defect and donor concentrations is beneficial to boost photocatalytic performance. It is demonstrated that an appropriate material design to suppress generation of donor species actually improves photocatalytic activity. Numerical modeling of steady state carrier concentrations suggests that an asymmetric built-in potential in photocatalyst particles enhances charge separation and thus extends the lifetimes of photoexcited carriers. On the basis of the recent findings, we suggest strategies to improve the reaction efficiency of photocatalytic water splitting
Chalcopyrite Thin Film Materials for Photoelectrochemical Hydrogen Evolution from Water under Sunlight
Copper chalcopyrite is a promising candidate for a photocathode material for photoelectrochemical (PEC) water splitting because of its high half-cell solar-to-hydrogen conversion efficiency (HC-STH), relatively simple and low-cost preparation process, and chemical stability. This paper reviews recent advances in copper chalcopyrite photocathodes. The PEC properties of copper chalcopyrite photocathodes have improved fairly rapidly: HC-STH values of 0.25% and 8.5% in 2012 and 2015, respectively. On the other hand, the onset potential remains insufficient, owing to the shallow valence band maximum mainly consisting of Cu 3d orbitals. In order to improve the onset potential, we explored substituting Cu for Ag and investigate the PEC properties of silver gallium selenide (AGSe) thin film photocathodes for varying compositions, film growth atmospheres, and surfaces. The modified AGSe photocathodes showed a higher onset potential than copper chalcopyrite photocathodes. It was demonstrated that element substitution of copper chalcopyrite can help to achieve more efficient PEC water splitting
Effects of Se Incorporation in La5Ti2CuS5O7 by Annealing on Physical Properties and Photocatalytic H-2 Evolution Activity
Oxysulfoselenide semiconductor photocatalysts absorb light at longer wavelengths than the corresponding oxysulfides. However, the synthesis of oxysulfoselenides is challenging due to excessive particle growth and the limited availability of metal selenide precursors. In this study, a La5Ti2CuS5O7 (LTCSO) oxysulfide was annealed with Se powder in sealed, evacuated quartz tubes to obtain LTCSO:Se photocatalysts, and the properties of these materials were investigated. Se was found to be incorporated into the LTCSO upon heating at 973 K or higher, and the Se/(S + Se) ratio was increased to a maximum of 0.3 upon repeating the heat treatment twice. The addition of Se extended the absorption edge of the LTCSO and thus increased its photocatalytic H-2 evolution activity at longer wavelength. Even so, the apparent quantum yield at shorter wavelengths was reduced, which is similar to the results obtained for La5Ti2Cu(S1-xSe)(5)O-7(LTCS1-xSexO) solid solutions. Overall water splitting was achieved by constructing photocatalyst sheets using LTCSO:Se and LTCS1-xSexO as hydrogen evolution photocatalysts and BiVO4 as an oxygen evolution photocatalyst. Heat treatment with Se is evidently an effective method for the transformation of oxysulfide photocatalysts to oxysulfoselenides that promote photocatalytic H-2 evolution and have longer absorption edge wavelengths