Hybrid solar cells from water-soluble polymers

We report on the use of a water-soluble, light-absorbing polythiophene polymer to fabricate novel photovoltaic devices. The polymer is a water-soluble thiophene known as sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] or PTEBS. The intention is to take advantage of the properties of conjugated polymers (flexible, tunable, and easy to process) and incorporate the additional benefits of water solubility (easily controlled evaporation rates and environmentally friendly). The PTEBS polythiophene has shown significant photovoltaic response and has been found to be effective for making solar cells. To date, solar cells in three different configurations have been produced: titanium dioxide (TiO2) bilayer cells, TiO2 bulk heterojunction solar cells, and carbon nanotubes (CNTs) in bulk heterojunctions. The best performance thus far has been achieved with TiO2 bilayer devices. These devices have an open circuit voltage (Voc) of 0.84V, a short circuit current (Jsc) of 0.15 mA/cm2, a fill factor (ff) of 0.91, and an efficiency (η) of 0.15 %

Water-soluble polythiophene∕nanocrystalline TiO2 solar cells

We report the characteristics of polymer∕nanocrystalline solar cells fabricated using an environmentally friendly water-soluble polythiophene and TiO2 in a bilayer configuration. The cells were made by dropping the polymer onto a TiO2nanocrystallinefilm and then repeatedly sweeping a clean glass rod across the polymer as it dried. The devices showed an open circuit voltage of 0.81 V, a short circuit current density of 0.35mA/cm2, a fill factor of 0.4, and an energy conversion efficiency of 0.13%. The water-soluble polythiophene showed significant photovoltaic behavior and the potential for use in solar cells

Characteristics of water-soluble polythiophene: TiO2 composite and its application in photovoltaics

We have studied the characteristics of composites of an environmentally friendly water-soluble polythiophene sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] (PTEBS) and TiO2. We observed that the ultraviolet-visible absorption spectrum of low molecular weight PTEBS is redshifted possibly due to the formation of aggregates. Cyclic voltammetry reveals the values of highest occupied molecular orbitals and lowest unoccupied molecular orbitals for PTEBS. A factor of 7 in photoluminescence quenching indicates that the exciton dissociation and charge separation occur successfully at the PTEBS: TiO2 (1:1 by weight) interface. This enhances the possibility that the separated charges will reach the electrodes before recombining. Scanning electron micrograph images show how the PTEBS and TiO2 are interconnected and form paths to the electrodes to improve charge transport. Photovoltaic devices with TiO2:PTEBS composite achieved an energy conversion efficiency of η=0.015%, a short circuit current of JSC=0.22mA/cm2, an open circuit voltage of VOC=0.72V, and a fill factor of FF=0.29 under ∼300mW/cm2 white light illumination

Hybrid Solar Cells from Water-Soluble Polymers

We report on the use of a water-soluble, light-absorbing polythiophene polymer to fabricate novel photovoltaic devices. The polymer is a water-soluble thiophene known as sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] or PTEBS. The intention is to take advantage of the properties of conjugated polymers (flexible, tunable, and easy to process) and incorporate the additional benefits of water solubility (easily controlled evaporation rates and environmentally friendly). The PTEBS polythiophene has shown significant photovoltaic response and has been found to be effective for making solar cells. To date, solar cells in three different configurations have been produced: titanium dioxide (TiO 2 ) bilayer cells, TiO 2 bulk heterojunction solar cells, and carbon nanotubes (CNTs) in bulk heterojunctions. The best performance thus far has been achieved with TiO 2 bilayer devices. These devices have an open circuit voltage (V oc ) of 0.84 V, a short circuit current (J sc ) of 0.15 mA/cm 2 , a fill factor (ff ) of 0.91, and an efficiency (η) of 0.15%

Hybrid TiO2 Solar Cells Produced from Aerosolized Nanoparticles of Water-Soluble Polythiophene Electron Donor Layer

Hybrid solar cells (HSCs) with water soluble polythiophene sodium poly[2-(3-thienyl)-ethyloxy-4-butylsulfonate] (PTEBS) thin films produced using electrospray deposition (ESD) were fabricated, tested, and modeled and compared to devices produced using conventional spin coating. A single device structure of FTO/TiO2/PTEBS/Au was used to study the effects of ESD of the PTEBS layer on device performance. ESD was found to increase the short circuit current density (Jsc) by a factor of 2 while decreasing the open circuit voltage (Voc) by half compared to spin coated PTEBS films. Comparable efficiencies of 0.009% were achieved from both device construction types. Current-voltage curves were modeled using the characteristic solar cell equation and showed a similar increase in generated photocurrent with an increase by two orders of magnitude in the saturation current in devices from ESD films. Increases in Jsc are attributed to an increase in the interfacial contact area between the TiO2 and PTEBS layers, while decreases in Voc are attributed to incomplete film formation from ESD

Electrokinetic separation of co-solutes into bimodal fibers by electrospinning

Composite and chemically/physically distinct fibers of sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] (PTEBS) and polyethylene oxide (PEO) were formed by electrospinning from a homogeneous aqueous solution containing PTEBS and PEO co-solutes. Composite nanofibers of diameter of ∼60nm were electrospun from an aqueous solution. The addition of ammonium hydroxide (NH4OH) to the water solution resulted in “bimodal” electrospun fibers consisting of distinct large diameter white PEO fiber segments and small diameter black PTEBS fiber segments. The optical absorptionspectrum of the composite PTEBS/PEO nanofibers did not exhibit the characteristic peak around 460nm, which is present in the bulk spectrum

Nanostructured solid-state hybrid photovoltaic cells fabricated by electrostatic layer-by-layer deposition

We report on the fabrication of hybrid organic/inorganic photovoltaic cells utilizing layer-by-layer deposition of water-soluble polyions and nanocrystals. A bulk heterojunction structure was created consisting of alternating layers of the p-conductive polythiophene derivative poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] and n-conductive TiO2nanoparticles. We fabricated working devices with the heterostructure sandwiched between suitable charge carrier blocking layers and conducting oxide and metal electrodes, respectively. We analyzed the influence of the thickness and nanostructure of the active layer on the cell performance and characterized the devices in terms of static and transient current response with respect to illumination and voltage conditions. We observed reproducible and stable photovoltaic behavior with photovoltages of up to 0.9 V

Electrospun Polymer-Fiber Solar Cell

A novel electrospun polymer-fiber solar cell was synthesized by electrospinning a 1 : 2.5 weight% ratio mixture of poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) and [6,6]-phenyl C61 butyric acid methyl ester (PCBM) resulting in bulk heterojunctions. Electrospinning is introduced as a technique that may increase polymer solar cell efficiency, and a list of advantages of the technique applied to solar cells is discussed. The device achieved a power conversion efficiency of η = 3.08 x 10-7%. The absorption and photoluminescence of MEH-PPV nanofibers are compared to thin films of the same material. Electrospun nanofibers are discussed as a favorable structure for application in polymer solar cells

Hydrothermal Preparation of Gd+3 -Doped Titanate Nanotubes: Magnetic Properties and Photovoltaic Performance

Pure and Gd+3 -doped titanate nanotubes (TNTs) materials were synthesized by a hydrothermal method. Their morphology, optical properties, thermal stability, and magnetic properties were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), UV-Vis spectroscopy, thermal analysis, and magnetic measurements. It was found that doping renders Gd+3-TNT visible light active and results in smaller crystallite size and larger surface area as well as higher thermal stability compared to pure titanate nanotubes. The estimated magnetic moments point to presence of weak antiferromagnetic interaction. Application of the prepared Gd+3-TNT for modifying conventional photoanodes in polymer solar cells was attempted. Preliminary results show slightly improved photovoltaic energy conversion efficiency in the devices containing the newly designed Gd+3 -doped nanotubes

DIAGONAL-FLOW, GAP-PICKUP GENERATOR ROTOR HEAT TRANSFER MODEL

ABSTRACT A computational model of the temperature distribution in a hydrogen-cooled, diagonal-flow, gap-pickup generator rotor has been developed. The model will aid in the analysis of the uprate capabilities of turbo-generators during steam turbine upgrades. Under certain operating conditions, knowledge of hot-spot temperatures and the temperature profile in the rotor windings is indispensable in determining the proper rating levels and loading limits. Following a general description of gap-pickup generator rotors and the advantages associated with their use, a description of the methods used in analyzing the hydrogen flow and heat transfer characteristics are presented. The development of the computer model is described with an overview of the design options available. Finally, a sample calculation is presented with an interpretation of the significance of the results