Hydrothermal Cobalt Doping of Titanium Dioxide Nanotubes towards Photoanode Activity Enhancement

Doping and modification of TiO2 nanotubes were carried out using the hydrothermal method. The introduction of small amounts of cobalt (0.1 at %) into the structure of anatase caused an increase in the absorption of light in the visible spectrum, changes in the position of the flat band potential, a decrease in the threshold potential of water oxidation in the dark, and a significant increase in the anode photocurrent. The material was characterized by the SEM, EDX, and XRD methods, Raman spectroscopy, XPS, and UV-Vis reflectance measurements. Electrochemical measurement was used along with a number of electrochemical methods: chronoamperometry, electrochemical impedance spectroscopy, cyclic voltammetry, and linear sweep voltammetry in dark conditions and under solar light illumination. Improved photoelectrocatalytic activity of cobalt-doped TiO2 nanotubes is achieved mainly due to its regular nanostructure and real surface area increase, as well as improved visible light absorption for an appropriate dopant concentration

The influence of photointercalaction and photochromism effects on the photocatalytic properties of electrochemically obtained maze-like MoO3 microstructures

Molybdenum oxide (α-MoO3) thin films with oriented crystalline facets were synthesised by anodization of Mo foils. The obtained samples were exposed to UV–Vis illumination in aqueous electrolytes providing different cations. The morphology and structure of modified samples were investigated. The effect of photointercalated alkali metal cations (Li+, Na+, K+) on optical and structural properties was studied using UV–vis and Raman spectroscopies, respectively. The observed energy band gap narrowing caused by the photochromic effect is found to affect the photocatalytic properties of the intercalated oxide. The photoactivity of obtained samples was tested during the photocatalytic process of methylene blue decomposition in the presence of 0.1 M Li2SO4, Na2SO4, K2SO4. After 2 h of continuous illumination, the photodecomposition efficiency of MB in the presence of K2SO4, Na2SO4 and Li2SO4 was 67%, 69% and 76%, respectively, whereas when no inorganic salt had been dissolved it reached only 57%.</p

Synergistic effects of nitrogen-doped carbon and praseodymium oxide in electrochemical water splitting

Abstract Hybrid materials featuring perovskite-type metal oxide in conjunction with heteroatom-doped graphene hold immense promise as alternatives to costly noble metal catalysts for electrochemical water splitting, facilitating the generation of environmentally friendly hydrogen. In this study, perovskite-type oxide containing praseodymium, barium, strontium, cobalt, and iron atoms dispersed in a carbon matrix as a catalyst is synthesized via annealing of the carbon material with substrates for the preparation of perovskite oxide. The mass ratio of reagents regulates the porous structure and elemental composition. The result of the hydrogen evolution reaction (HER), suggests that the hybrid catalysts exhibit intermediate HER kinetics compared to the commercial Pt/C and the catalyst without carbon. The Tafel slope for HER is lower for materials containing carbon, because of the improved reaction kinetics, facilitated proton transfer, and enhanced electrochemical surface area. Therefore, the study provides an effective strategy for the preparation of catalyst and their use as the active catalyst of water splitting

Improving the Performance of a Graphite Foil/Polyaniline Electrode Material by a Thin PEDOT:PSS Layer for Application in Flexible, High Power Supercapacitors

In this study, we present a novel strategy for enhancing polyaniline stability and thus obtaining an electrode material with practical application in supercapacitors. A promising (graphite foil/polyaniline/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) GF/PANI/PEDOT:PSS) electrode material was characterized and used in the construction of a symmetric supercapacitor that provides an outstanding high power density. For this purpose, the electropolymerization of PANI was carried out on a graphite foil and then a thin protective layer of PEDOT:PSS was deposited. The presence of the nanometer PEDOT:PSS layer made it possible to widen the electroactivity potential range of the electrode material. Moreover, the synergy between materials positively affected the amount of accumulated charge, and thus the thin PEDOT:PSS layer contributed to enhancing the specific capacity of the electrode material. The electrochemical performance of the GF/PANI/PEDOT:PSS electrode, as well as the symmetrical supercapacitor, was investigated by cyclic voltammetry and galvanostatic charge/discharge cycles in 1 M H2SO4 at room temperature. The fabricated electrode material shows a high specific capacitance (Csp) of 557.4 Fg−1 and areal capacitance (Careal) of 2600 mF·cm−2 in 1 M H2SO4 at a current density of 200 mA·cm−2 (~4 A·g−1). The supercapacitor performance was studied and the results show that a thin PEDOT:PSS layer enables cycling stability improvement of the device from 54% to 67% after 10,000 cycles, and provides a high specific capacity (159.8 F·g−1) and a maximum specific power (18,043 W·kg−1) for practical applications

An Easy and Ecological Method of Obtaining Hydrated and Non-Crystalline WO3−x for Application in Supercapacitors

In this work, we report the synthesis of hydrated and non-crystalline WO3 flakes (WO3&minus;x) via an environmentally friendly and facile water-based strategy. This method is described, in the literature, as exfoliation, however, based on the results obtained, we cannot say unequivocally that we have obtained an exfoliated material. Nevertheless, the proposed modification procedure clearly affects the morphology of WO3 and leads to loss of crystallinity of the material. TEM techniques confirmed that the process leads to the formation of WO3 flakes of a few nanometers in thickness. X-ray diffractograms affirmed the poor crystallinity of the flakes, while spectroscopic methods showed that the materials after exfoliation were abundant with the surface groups. The thin film of hydrated and non-crystalline WO3 exhibits a seven times higher specific capacitance (Cs) in an aqueous electrolyte than bulk WO3 and shows an outstanding long-term cycling stability with a capacitance retention of 92% after 1000 chronopotentiometric cycles in the three-electrode system. In the two-electrode system, hydrated WO3&minus;x shows a Cs of 122 F g&minus;1 at a current density of 0.5 A g&minus;1. The developed supercapacitor shows an energy density of 60 Whkg&minus;1 and power density of 803 Wkg&minus;1 with a decrease of 16% in Csp after 10,000 cycles. On the other hand, WO3&minus;x is characterized by inferior properties as an anode material in lithium-ion batteries compared to bulk WO3. Lithium ions intercalate into a WO3 crystal framework and occupy trigonal cavity sites during the electrochemical polarization. If there is no regular layer structure, as in the case of the hydrated and non-crystalline WO3, the insertion of lithium ions between WO3 layers is not possible. Thus, in the case of a non-aqueous electrolyte, the specific capacity of the hydrated and non-crystalline WO3 electrode material is much lower in comparison with the specific capacity of the bulk WO3-based anode material

Modification of TiO2 nanotubes by graphene–strontium and cobalt molybdate perovskite for efficient hydrogen evolution reaction in acidic medium

Abstract Herein, we demonstrate that modification of TiO2 nanotubes with graphene–strontium and cobalt molybdate perovskite can turn them into active electrocatalysts for hydrogen evolution reaction (HER). For this purpose, a simple method of hydrothermal synthesis of perovskites was developed directly on the TiO2 nanotubes substrate. Moreover, the obtained hybrids were also decorated with graphene oxide (GO) during one-step hydrothermal synthesis. The obtained materials were characterized by scanning electron microscopy with energy dispersive X-ray analysis, Raman spectroscopy, and X-ray diffraction analysis. Catalytic properties were verified by electrochemical methods (linear voltammetry, chronopotentiometry). The obtained hybrids were characterized by much better catalytic properties towards hydrogen evolution reaction compared to TiO2 and slightly worse than platinum. The optimized hybrid catalyst (decorated by GO) can drive a cathodic current density of 10 mA cm−2 at an overpotential of 121 mV for HER with a small Tafel slope of 90 mV dec−1 in 0.2 M H2SO4

Widening of the electroactivity potential range by composite formation – capacitive properties of TiO2/BiVO4/PEDOT:PSS electrodes in contact with an aqueous electrolyte

Composites based on the titania nanotubes were tested in aqueous electrolyte as a potential electrode material for energy storage devices. The nanotubular morphology of TiO2 was obtained by Ti anodization. TiO2 nanotubes were covered by a thin layer of bismuth vanadate using pulsed laser deposition. The formation of the TiO2/BiVO4 junction leads to enhancement of pseudocapacitance in the cathodic potential range. The third component, the conjugated polymer PEDOT:PSS, was electrodeposited from an electrolyte containing the monomer EDOT and NaPSS as a source of counter ions. Each stage of modification and deposition affected the overall capacitance and allowed for an expansion of the potential range of electroactivity. Multiple charge/discharge cycles were performed to characterize the electrochemical stability of the inorganic–organic hybrid electrode. Capacitance values higher than 10 mF·cm−2 were maintained even after 10000 galvanostatic cycles (ic = ia = 0.5 mA·cm−2)

Scaling Up the Process of Titanium Dioxide Nanotube Synthesis and Its Effect on Photoelectrochemical Properties

In this work, for the first time, the influence of scaling up the process of titanium dioxide nanotube (TiO2NT) synthesis on the photoelectrochemical properties of TiO2 nanotubes is presented. Titanium dioxide nanotubes were obtained on substrates of various sizes: 2 × 2, 4 × 4, 5 × 5, 6 × 6, and 8 × 8 cm2. The electrode material was characterized using scanning electron microscopy as well as Raman and UV–vis spectroscopy in order to investigate their morphology, crystallinity, and absorbance ability, respectively. The obtained electrodes were used as photoanodes for the photoelectrochemical water splitting. The surface analysis was performed, and photocurrent values were determined depending on their place on the sample. Interestingly, the values of the obtained photocurrent densities in the center of each sample were similar and were about 80 µA·cm2. The results of our work show evidence of a significant contribution to wider applications of materials based on TiO2 nanotubes not only in photoelectrochemistry but also in medicine, supercapacitors, and sensors

Controlling crystallites orientation and facet exposure for enhanced electrochemical properties of polycrystalline MoO3 films

Abstract This study focuses on the development and optimization of MoO3 films on commercially available FTO substrates using the pulsed laser deposition (PLD) technique. By carefully selecting deposition conditions and implementing post-treatment procedures, precise control over crystallite orientation relative to the substrate is achieved. Deposition at 450 °C in O2 atmosphere results in random crystallite arrangement, while introducing argon instead of oxygen to the PLD chamber during the initial stage of sputtering exposes the (102) and (011) facets. On the other hand, room temperature deposition leads to the formation of amorphous film, but after appropriate post-annealing treatment, the (00k) facets were exposed. The deposited films are studied using SEM and XRD techniques. Moreover, electrochemical properties of FTO/MoO3 electrodes immersed in 1 M AlCl3 aqueous solution are evaluated using cyclic voltammetry and electrochemical impedance spectroscopy. The results demonstrate that different electrochemical processes are promoted based on the orientation of crystallites. When the (102) and (011) facets are exposed, the Al3+ ions intercalation induced by polarization is facilitated, while the (00k) planes exposure leads to the diminished hydrogen evolution reaction overpotential