Fabrication and characterization of biomimetic hydroxyapatite thin films for bone implants by direct ablation of a biogenic source

Biomimetic bone apatite coatings were realized for the first time by the novel Ionized Jet Deposition technique. Bone coatings were deposited on titanium alloy substrates by pulsed electron ablation of deproteinized bovine bone shafts in order to resemble bone apatite as closely as possible. The composition, morphology and mechanical properties of the coatings were characterized by GI-XRD, FT-IR, SEM-EDS, AFM, contact angle measurements, micro-scratch and screw-insertion tests. Different post-treatment annealing conditions (from 350 °C to 425 °C) were investigated. Bone apatite coatings exhibited a nanostructured surface morphology and a composition closely resembling that of the deposition target (i.e. natural bone apatite), also regarding the presence of magnesium and sodium ions. Crystallinity and composition of the coatings were strongly influenced by annealing temperature and duration; in particular, upon annealing at 400 °C and above, a crystallinity similar to that of bone was achieved. Finally, adhesion to the titanium substrate and hydrophilicity were significantly enhanced upon annealing, all characteristics being known to have a strong positive impact on promoting host cells attachment, proliferation and differentiation

A Comprehensive Microstructural and Compositional Characterization of Allogenic and Xenogenic Bone: Application to Bone Grafts and Nanostructured Biomimetic Coatings

Bone grafts and bone-based materials are widely used in orthopedic surgery. However, the selection of the bone type to be used is more focused on the biological properties of bone sources than physico-chemical ones. Moreover, although biogenic sources are increasingly used for deposition of biomimetic nanostructured coatings, the influence of specific precursors used on coating’s morphology and composition has not yet been explored. Therefore, in order to fill this gap, we provided a detailed characterization of the properties of the mineral phase of the most used bone sources for allografts, xenografts and coating deposition protocols, not currently available. To this aim, several bone apatite precursors are compared in terms of composition and morphology. Significant differences are assessed for the magnesium content between female and male human donors, and in terms of Ca/P ratio, magnesium content and carbonate substitution between human bone and different animal bone sources. Prospectively, based on these data, bone from different sources can be used to obtain bone grafts having slightly different properties, depending on the clinical need. Likewise, the suitability of coating-based biomimetic films for specific clinical musculoskeletal application may depend on the type of apatite precursor used, being differently able to tune surface morphology and nanostructuration, as shown in the proof of concepts of thin film manufacturing here presented

Magnetic Forces And Magnetized Biomaterials Provide Dynamic Flux Information During Bone Regeneration

The fascinating prospect to direct tissue regeneration by magnetic activation has been recently explored. In this study we investigate the possibility to boost bone regeneration in an experimental defect in rabbit femoral condyle by combining static magnetic fields and magnetic biomaterials. NdFeB permanent magnets are implanted close to biomimetic collagen/hydroxyapatite resorbable scaffolds magnetized according to two different protocols. Permanent magnet only or non-magnetic scaffolds are used as controls. Bone tissue regeneration is evaluated at 12 weeks from surgery from a histological, histomorphometric and biomechanical point of view. The reorganization of the magnetized collagen fibers under the effect of the static magnetic field generated by the permanent magnet produces a highly-peculiar bone pattern, with highly-interconnected trabeculae orthogonally oriented with respect to the magnetic field lines. In contrast, only partial defect healing is achieved within the control groups. We ascribe the peculiar bone regeneration to the transfer of micro-environmental information, mediated by collagen fibrils magnetized by magnetic nanoparticles, under the effect of the static magnetic field. These results open new perspectives on the possibility to improve implant fixation and control the morphology and maturity of regenerated bone providing “in site” forces by synergically combining static magnetic fields and biomaterials

Pulsed plasma deposition of zirconia thin films on UHMWPE: proof of concept of a novel approach for joint prosthetic implants

Wear of ultra-high molecular weight polyethylene (UHMWPE) has been recognized as the main cause for long-term revision in joint arthroplasty. A new approach to overcome this detrimental issue is here presented: zirconia (ZrO2) thin films were directly deposited onto the surface of UHMWPE by Pulsed Plasma Deposition (PPD) technique. The obtained films were structurally, morphologically and mechanically characterized by X-ray diffraction, scanning electron microscopy and nanoindentation tests, respectively. The critical fracture load was estimated by the analysis of the indenter footprints, while the adhesion degree was evaluated by a cross-cut tape test. Zirconia films exhibited a fully cubic structure, with densely packed grains, whereas mechanical tests showed that hard, tough and well-adherent films were deposited. These preliminary results suggested the feasibility of pursuing this alternative route to improve UHMPWE performances while preserving its well-established mechanical properties. © 2013 The Royal Society of Chemistry

NANOMECHANICAL CHARACTERIZATION of ZIRCONIA THIN FILMS DEPOSITED on UHMWPE by PULSED PLASMA DEPOSITION

Plastic deformation and wear of the ultra-high molecular weight polyethylene (UHMWPE) insert have been pointed out as major issues relating to the long-term stability of an orthopaedic implant. The deposition of protective hard, tough and well-adhered zirconia ( ZrO2) thin films directly on the surface of the UHMWPE component via the Pulsed Plasma Deposition (PPD) technique has been already demonstrated to be a feasible way to approach this problem. In the current study, the tribo-mechanical properties of ZrO2-coated UHMWPE with respect to pristine UHMWPE were investigated in detail. Specifically, strength to local plastic deformation, indentation work portioning and creep behavior were evaluated through nanoindentation and micro-scratch tests. Further, preliminary wear data (i.e., rate and volume) were obtained by tribology tests mating coated and pristine UHMWPE with an alumina ball under dry conditions. The results of the mechanical tests evidenced a strong reduction of plastic deformation under both normal and tangential local loads and a drop of the 80% of the creep phenomenon for coated UHMWPE compared to pristine UHMWPE. Despite tribological tests showed similar wear data for coated and pristine UHMWPE, a different wear mechanism was detected between the two groups. The reported results supported the possibility to pursue this novel approach of depositing ZrO2thin film to protect the UHWMPE insert and enhance the long-term stability of the orthopaedic implants.</jats:p

A Comprehensive Microstructural and Compositional Characterization of Allogenic and Xenogenic Bone: Application to Bone Grafts and Nanostructured Biomimetic Coatings

Bone grafts and bone-based materials are widely used in orthopedic surgery. However, the selection of the bone type to be used is more focused on the biological properties of bone sources than physico-chemical ones. Moreover, although biogenic sources are increasingly used for deposition of biomimetic nanostructured coatings, the influence of specific precursors used on coating&rsquo;s morphology and composition has not yet been explored. Therefore, in order to fill this gap, we provided a detailed characterization of the properties of the mineral phase of the most used bone sources for allografts, xenografts and coating deposition protocols, not currently available. To this aim, several bone apatite precursors are compared in terms of composition and morphology. Significant differences are assessed for the magnesium content between female and male human donors, and in terms of Ca/P ratio, magnesium content and carbonate substitution between human bone and different animal bone sources. Prospectively, based on these data, bone from different sources can be used to obtain bone grafts having slightly different properties, depending on the clinical need. Likewise, the suitability of coating-based biomimetic films for specific clinical musculoskeletal application may depend on the type of apatite precursor used, being differently able to tune surface morphology and nanostructuration, as shown in the proof of concepts of thin film manufacturing here presented

Plasma-assisted deposition of bone apatite-like thin films from natural apatite

In orthopedics and dentistry, novel approaches for fabricating biomimetic and mechanically robust bioactive coatings are highly desirable in order to truly improve the clinical results of coated implants compared to uncoated ones. In this paper, a biological-like apatite coating is deposited for the first time by plasma-assisted deposition of a natural apatite source. Specifically, we deposited bone apatite-like (BAL) thin films from bone apatite targets by pulsed electron deposition (PED). Morphology, composition, structure and mechanical properties of as-deposited and annealed BAL and stoichiometric hydroxyapatite (HA) films were investigated. While as-deposited BAL and HA films were poorly crystalline at room temperature, they crystallized to an extent very close to that of natural apatite when annealed at 400 °C. In addition, FTIR analysis pointed out that BAL films closely resembled the composition of the starting natural apatite target. Finally, nanoindentation tests indicated that BAL films with high mechanical properties could be deposited by PED