Thermal spray coatings for electromagnetic wave absorption and interference shielding: a review and future challenges

This review paper aims to consolidate scattered literature on thermally sprayed coatings with non-ionising electromagnetic (EM) wave absorption and shielding over specific wavelengths potentially useful in diverse applications (e.g., microwave to millimeter wave, solar selective, photocatalytic, interference shielding, thermal barrier-heat/emissivity). Materials EM properties such as electric permittivity, magnetic permeability, electrical conductivity, and dielectric loss are critical due to which a material can respond to absorbed, reflected, transmitted, or may excite surface electromagnetic waves at frequencies typical of electromagnetic radiations. Thermal spraying is a standard industrial practice used for depositing coatings where the sprayed layer is formed by successive impact of fully or partially molten droplets/particles of a material (used in the form of powder or wire) exposed to high or moderate temperatures and velocities. However, as an emerging novel application of an existing thermal spray techniques, some special considerations are warranted for targeted development involving relevant characterisation. Key potential research areas of development relating to material selection and coating fabrication strategies and their impact on existing practices in the field are identified. The study shows a research gap in the feedstock materials design and doping (including hollow and yolk-shelled structure types) and their complex selection covered by thermally sprayed coatings that can be critical to advancing applications exploiting their electromagnetic propertie

Large-scale manufacturing route to metamaterial coatings using thermal spray techniques and their response to solar radiation

Metamaterials, an artificial periodic two-or three-dimensional configuration can change propagation characteristics of electromagnetic waves (i.e., reflection, transmission, absorption). The current challenges in the field of metamaterial coatings are their manufacturing in large scale and large length scale. There is a clear need to enhance process technologies and scalability of these. Thermal spraying is a method used to deposit small to large scale coatings where the sprayed layer is typically formed by successive impact of fully or partially molten particles of a material exposed to various process conditions. This work aims to investigate the feasibility to manufacture large scale metamaterial coatings using the thermal spray technique and examine their response to solar radiation. Two types of coatings namely, Cr2O3 and TiO2 were deposited onto various substrates (e.g., steel, aluminium, glass, indium tin oxide (ITO) coated glass) with a fine wire mesh (143 µm and 1 mm aperture sizes) as the masking sheet to manipulate the surface pattern using suspension high-velocity oxy-fuel thermal spraying (S-HVOF) and atmospheric plasma-sprayed (APS) methods, respectively. Post deposition, their responses subjected to electromagnetic wave (between 250 nm to 2500 nm or Ultraviolet (UV)-Visible (Vis)-Infrared (IR) region) were characterised. The additional microstructural characterisation was performed using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), three-dimensional profilometry and optical spectroscopy. It is demonstrated that through novel application of thermal spray techniques, large scale manufacturing of metamaterial coating is possible, and such material can affect the electromagnetic wave propagation. Comparison between Cr2O3 and TiO2 coatings on aluminium substrates showed reduced three orders of reduced reflectance for Cr2O3 coatings (for 1 mm aperture size) throughout the spectrum. It was concluded that for a similar bandgap, Cr2O3 coatings on aluminium substrate will yield improved optical performance than TiO2 coating, and hence more useful to fabricate opto-electronic devices

A comprehensive 1000 Genomes-based genome-wide association meta-analysis of coronary artery disease

Existing knowledge of genetic variants affecting risk of coronary artery disease (CAD) is largely based on genome-wide association study (GWAS) analysis of common SNPs. Leveraging phased haplotypes from the 1000 Genomes Project, we report a GWAS meta-analysis of ∼185,000 CAD cases and controls, interrogating 6.7 million common (minor allele frequency (MAF) > 0.05) and 2.7 million low-frequency (0.005 < MAF < 0.05) variants. In addition to confirming most known CAD-associated loci, we identified ten new loci (eight additive and two recessive) that contain candidate causal genes newly implicating biological processes in vessel walls. We observed intralocus allelic heterogeneity but little evidence of low-frequency variants with larger effects and no evidence of synthetic association. Our analysis provides a comprehensive survey of the fine genetic architecture of CAD, showing that genetic susceptibility to this common disease is largely determined by common SNPs of small effect size. © 2015 Nature America, Inc

Garantenstellung des Wohnungsinhabers bei Angriffen auf einen Gast

Garantenstellung des Wohnungsinhabers bei Angriffen auf einen Gast. - In: Juristische Schulung. 18. 1978. S. 308-31