Probing low-density carriers in a single atomic layer using terahertz parallel-plate waveguides

As novel classes of two-dimensional (2D) materials and heterostructures continue to emerge at an increasing pace, methods are being sought for elucidating their electronic properties rapidly, non-destructively, and sensitively. Terahertz (THz) time-domain spectroscopy is a well-established method for characterizing charge carriers in a contactless fashion, but its sensitivity is limited, making it a challenge to study atomically thin materials, which often have low conductivities. Here, we employ THz parallel-plate waveguides to study monolayer graphene with low carrier densities. We demonstrate that a carrier density of ~2 × 1011 cm−2, which induces less than 1% absorption in conventional THz transmission spectroscopy, exhibits ~30% absorption in our waveguide geometry. The amount of absorption exponentially increases with both the sheet conductivity and the waveguide length. Therefore, the minimum detectable conductivity of this method sensitively increases by simply increasing the length of the waveguide along which the THz wave propagates. In turn, enabling the detection of low-conductivity carriers in a straightforward, macroscopic configuration that is compatible with any standard time-domain THz spectroscopy setup. These results are promising for further studies of charge carriers in a diverse range of emerging 2D materials

Using the Plasmon Linewidth To Calculate the Time and Efficiency of Electron Transfer between Gold Nanorods and Graphene

We present a quantitative analysis of the electron transfer between single gold nanorods and monolayer graphene under no electrical bias. Using single-particle dark-field scattering and photoluminescence spectroscopy to access the homogeneous linewidth, we observe broadening of the surface plasmon resonance for gold nanorods on graphene compared to nanorods on a quartz substrate. Because of the absence of spectral plasmon shifts, dielectric interactions between the gold nanorods and graphene are not important and we instead assign the plasmon damping to charge transfer between plasmon-generated hot electrons and the graphene that acts as an efficient acceptor. Analysis of the plasmon linewidth yields an average electron transfer time of 160 ± 30 fs, which is otherwise difficult to measure directly in the time domain with single-particle sensitivity. In comparison to intrinsic hot electron decay and radiative relaxation, we furthermore calculate from the plasmon linewidth that charge transfer between the gold nanorods and the graphene support occurs with an efficiency of ∼10%. Our results are important for future applications of light harvesting with metal nanoparticle plasmons and efficient hot electron acceptors as well as for understanding hot electron transfer in plasmon-assisted chemical reactions

Bottom-up Approach toward Single-Crystalline VO₂‑Graphene Ribbons as Cathodes for Ultrafast Lithium Storage

Although lithium ion batteries have gained commercial success owing to their high energy density, they lack suitable electrodes capable of rapid charging and discharging to enable a high power density critical for broad applications. Here, we demonstrate a simple bottom-up approach toward single crystalline vanadium oxide (VO₂) ribbons with graphene layers. The unique structure of VO₂-graphene ribbons thus provides the right combination of electrode properties and could enable the design of high-power lithium ion batteries. As a consequence, a high reversible capacity and ultrafast charging and discharging capability is achieved with these ribbons as cathodes for lithium storage. A full charge or discharge is capable in 20 s. More remarkably, the resulting electrodes retain more than 90% of the initial capacity after cycling more than 1000 times at an ultrahigh rate of 190C, providing the best reported rate performance for cathodes in lithium ion batteries to date

ARTICLE Fracture toughness of graphene

Perfect graphene is believed to be the strongest material. However, the useful strength of large-area graphene with engineering relevance is usually determined by its fracture toughness, rather than the intrinsic strength that governs a uniform breaking of atomic bonds in perfect graphene. To date, the fracture toughness of graphene has not been measured. Here we report an in situ tensile testing of suspended graphene using a nanomechanical device in a scanning electron microscope. During tensile loading, the pre-cracked graphene sample fractures in a brittle manner with sharp edges, at a breaking stress substantially lower than the intrinsic strength of graphene. Our combined experiment and modelling verify the applicability of the classic Griffith theory of brittle fracture to graphene. The fracture toughness of graphene is measured as the critical stress intensity factor of 4:0 AE 0:6 MPa ffiffiffiffi m p and the equivalent critical strain energy release rate of 15.9 J m À 2 . Our work quantifies the essential fracture properties of graphene and provides mechanistic insights into the mechanical failure of graphene

Achieving Highly Efficient, Selective, and Stable CO2 Reduction on Nitrogen-Doped Carbon Nanotubes

The challenge in the electrosynthesis of fuels from CO2 is to achieve durable and active performance with cost-effective catalysts. Here, we report that carbon nanotubes (CNTs), doped with nitrogen to form resident electron-rich defects, can act as highly efficient and, more importantly, stable catalysts for the conversion of CO2 to CO. The unprecedented overpotential (-0.18 V) and selectivity (80%) observed on nitrogen-doped CNTs (NCNTs) are attributed to their unique features to facilitate the reaction, including (i) high electrical conductivity, (ii) preferable catalytic sites (pyridinic N defects), and (iii) low free energy for CO2 activation and high barrier for hydrogen evolution. Indeed, DFT calculations show a low free energy barrier for the potential-limiting step to form key intermediate COOH as well as strong binding energy of adsorbed CON and weak binding energy for the adsorbed CO. The highest selective site toward CO production is pyridinic N, and the NCNT-based electrodes exhibit no degradation over 10 h of continuous operation, suggesting the structural stability of the electrode

Anomalous high capacitance in a coaxial single nanowire capacitor

International audienc

Bottom-up Approach toward Single-Crystalline VO₂‑Graphene Ribbons as Cathodes for Ultrafast Lithium Storage

Although lithium ion batteries have gained commercial success owing to their high energy density, they lack suitable electrodes capable of rapid charging and discharging to enable a high power density critical for broad applications. Here, we demonstrate a simple bottom-up approach toward single crystalline vanadium oxide (VO₂) ribbons with graphene layers. The unique structure of VO₂-graphene ribbons thus provides the right combination of electrode properties and could enable the design of high-power lithium ion batteries. As a consequence, a high reversible capacity and ultrafast charging and discharging capability is achieved with these ribbons as cathodes for lithium storage. A full charge or discharge is capable in 20 s. More remarkably, the resulting electrodes retain more than 90% of the initial capacity after cycling more than 1000 times at an ultrahigh rate of 190C, providing the best reported rate performance for cathodes in lithium ion batteries to date

Nitrogen-Doped Graphene with Pyridinic Dominance as a Highly Active and Stable Electrocatalyst for Oxygen Reduction

The nitrogen-doped graphene (NG) with dominance of the pyridinic-N configuration is synthesized via a straightforward process including chemical vapor deposition (CVD) growth of graphene and postdoping with a solid nitrogen precursor of graphitic C₃N₄ at elevated temperature. The NG fabricated from CVD-grown graphene contains a high N content up to 6.5 at. % when postdoped at 800 °C but maintains high crystalline quality of graphene. The obtained NG exhibits high activity, long-standing stability, and outstanding crossover resistance for electrocatalysis of oxygen reduction reaction (ORR) in alkaline medium. The NG treated at 800 °C shows the best ORR performance. Further study of the dependence of ORR activity on different N functional groups in these metal-free NG electrodes provides deeper insights into the origin of ORR activity. Our results reveal that the pyridinic-N tends to be the most active N functional group to facilitate ORR at low overpotential via a four-electron pathway

Achieving Highly Efficient, Selective, and Stable CO2 Reduction on Nitrogen-Doped Carbon Nanotubes

The challenge in the electrosynthesis of fuels from CO2 is to achieve durable and active performance with cost-effective catalysts. Here, we report that carbon nanotubes (CNTs), doped with nitrogen to form resident electron-rich defects, can act as highly efficient and, more importantly, stable catalysts for the conversion of CO2 to CO. The unprecedented overpotential (-0.18 V) and selectivity (80%) observed on nitrogen-doped CNTs (NCNTs) are attributed to their unique features to facilitate the reaction, including (i) high electrical conductivity, (ii) preferable catalytic sites (pyridinic N defects), and (iii) low free energy for CO2 activation and high barrier for hydrogen evolution. Indeed, DFT calculations show a low free energy barrier for the potential-limiting step to form key intermediate COOH as well as strong binding energy of adsorbed CON and weak binding energy for the adsorbed CO. The highest selective site toward CO production is pyridinic N, and the NCNT-based electrodes exhibit no degradation over 10 h of continuous operation, suggesting the structural stability of the electrode

Graphene-Based Standalone Solar Energy Converter for Water Desalination and Purification

Harvesting solar energy for desalination and sewage treatment has been considered as a promising solution to produce clean water. However, state-of-the-art technologies often require optical concentrators and complicated systems with multiple components, leading to poor efficiency and high cost. Here, we demonstrate an extremely simple and standalone solar energy converter consisting of only an as-prepared 3D cross-linked honeycomb graphene foam material without any other supporting components. This simple all-in-one material can act as an ideal solar thermal converter capable of capturing and converting sunlight into heat, which in turn can distill water from various water sources into steam and produce purified water under ambient conditions and low solar flux with very high efficiency. High specific water production rate of 2.6 kg h^–1 m^–2 g^–1 was achieved with near ∼87% under 1 sun intensity and >80% efficiency even under ambient sunlight (<1 sun). This scalable sheet-like material was used to obtain pure drinkable water from both seawater and sewage water under ambient conditions. Our results demonstrate a competent monolithic material platform providing a paradigm change in water purification by using a simple, point of use, reusable, and low-cost solar thermal water purification system for a variety of environmental conditions