Development of an intense positron source using a crystal--amorphous hybrid target for linear colliders

In a conventional positron source driven by a few GeV electron beam, a high amount of heat is loaded into a positron converter target to generate intense positrons required by linear colliders, and which would eventually damage the converter target. A hybrid target, composed of a single crystal target as a radiator of intense gamma--rays, and an amorphous converter target placed downstream of the crystal, was proposed as a scheme which could overcome the problem.This paper describes the development of an intense positron source with the hybrid target. A series of experiments on positron generation with the hybrid target has been carried out with a 8--GeV electron beam at the KEKB linac. We observed that positron yield from the hybrid target increased when the incident electron beam was aligned to the crystal axis and exceeded the one from the conventional target with the converter target of the same thickness, when its thickness is less than about 2 radiation length. The measurements in the temperature rise of the amorphous converter target was successfully carried out by use of thermocouples. These results lead to establishment to the evaluation of the hybrid target as an intense positron source.Comment: 17pages, 10figure

Beam-Breakup Instability Theory for Energy Recovery Linacs

Here we will derive the general theory of the beam-breakup instability in recirculating linear accelerators, in which the bunches do not have to be at the same RF phase during each recirculation turn. This is important for the description of energy recovery linacs (ERLs) where bunches are recirculated at a decelerating phase of the RF wave and for other recirculator arrangements where different RF phases are of an advantage. Furthermore it can be used for the analysis of phase errors of recirculated bunches. It is shown how the threshold current for a given linac can be computed and a remarkable agreement with tracking data is demonstrated. The general formulas are then analyzed for several analytically solvable cases, which show: (a) Why different higher order modes (HOM) in one cavity do not couple so that the most dangerous modes can be considered individually. (b) How different HOM frequencies have to be in order to consider them separately. (c) That no optics can cause the HOMs of two cavities to cancel. (d) How an optics can avoid the addition of the instabilities of two cavities. (e) How a HOM in a multiple-turn recirculator interferes with itself. Furthermore, a simple method to compute the orbit deviations produced by cavity misalignments has also been introduced. It is shown that the BBU instability always occurs before the orbit excursion becomes very large.Comment: 12 pages, 6 figure

Experimental study of positron production from a 2.55-mm-thick silicon crystal target using 8-GeV channeling electron beams with high-bunch charges

We have investigated quenching phenomena of channeling radiation through positron production from a silicon crystal hit by a single-bunch electron beam with high-bunch charge at the 8-GeV electron/positron injector linac. The crystal axis, left angle bracket1 1 0right-pointing angle bracket, was aligned to the electron beam with a precise goniometer, and positrons produced in the forward direction with a momentum of 20 MeV/c were detected with a magnetic spectrometer. Positron yields were measured by varying the charge in a bunch with a typical bunch length of not, vert, similar10 ps from 0.1 nC to 2 nC. The corresponding instantaneous current density ranged from 0.15 × 104 to 1.2 × 104 A/cm2. The results show that, at these current densities, the positron yield is proportional to the bunch charge within the experimental accuracy, which implies that no non-linear phenomena are observed in channeling radiation

Enhancement of the Positron Intensity by a Tungsten Single Crystal Target at the KEKB Injector Linac

International audienceA new tungsten single-crystalline positron target has been successfully employed for generation of the intense positron beam at the KEKB injector linac in September 2006. The target is composed of a tungsten single-crystal with a thickness of 10.5 mm. The positron production target is bombarded at an incident electron energy of 4 GeV, and the produced positrons are collected and accelerated up to the final injection energy of 3.5 GeV in the succeeding sections. A conventional tungsten plate with a thickness of 14 mm has been used previously, and the conversion efficiency (Ne^+/Ne^-), the ratio between the number of positrons (Ne^+) captured in the positron capture section and the number of the incident electrons (Ne^-), was 0.20 on average. By replacing the tungsten plate with the tungsten crystal, it increased to 0.25 on average. The increase of the conversion efficiency has boosted the positron intensity to its maximum since the beginning of KEKB operation in 1999. Now this new positron source is stably operating and is contributing to increasing the integrated luminosity of the KEKB B-factory

Positron sources using channeling: A promising device for linear colliders

The need of intense and bright positron sources for linear colliders has urged the researches on polarized and unpolarized positrons. For 20 years, continuous theoretical and experimental investigations on unpolarized positron sources using axially channelled electrons in aligned monocrystals have pointed to efficient solutions concerning not only the source intensity, but also the minimization of the deposited energy. Simulations using the channelling programme of V. Strakhovenko associated to GEANT4, provided a description of such sources composed of tungsten crystals as photon radiators and amorphous tungsten as converters, the so-called hybrid source; the incident electron energies are taken between 5 and 10 GeV. Here, some applications are shown for CLIC, for which this source is the baseline, and also for ILC. The simulations are also concerning the test at KEK of such hybrid source, with a sweeping magnet separating the crystal radiator and an amorphous converter. Future developments on the simulation programme are also reported. The main issues for such sources are also analyzed

COMMISSIONING OF THE KEKB LINAC

Abstract The injector linac for the KEKB ring has been commissioned step by step since last autumn, while continuing the construction of the remaining parts as well as ordinary operation for beam injection into the Photon Factory. The commissioning has so far given quite satisfactory results: (1) A single-bunched beam with a charge of about 1.5 nC for direct injection into the ring was accelerated to the end of the linac (about 8 GeV)

OPTICS CORRECTION FOR KLYSTRON SWITCHING AT THE KEKB INJECTOR LINAC

Abstract For the high luminosity operation of the KEKB-factory, the beam injection time from the linac to the storage rings is desired to be short. However, the injection is sometimes interrupted by a temporary rf-trip of the klystron. In case of a serious failure, the klystron is switched to a spare one to compensate for the acceleration energy. After the switching, the injection is often degraded because of the beam optical mis-matching due to the change in the beam energy at each quadrupole. We have developed software which can estimate the beam energy at each quadrupole, calculate the optics so as to achieve the desired matching and change the settings of the relevant quadrupoles in short time. The experimental result of the recovery of the optical matching is also shown